Subscribe to Our Youtube Channel
Related Manuals for JETWAY JBC420U11 Series
Summary of Contents for JETWAY JBC420U11 Series
- Page 1 Quick Installation Guide NO. G03-JC420MU11QIG-F Rev: 1.0 Release Date: 2022-1-19 Notice: The photos in this file are for illustration purpose only. The model may not be the latest version. Please refer to the product you purchased for actual specification.
- Page 2 I/O Outlets...
- Page 3 Dimension and Outlines I. To Dissemble the Chassis 1. Locate the screws at the spots marked on this side of the system and unscrew them one by one.
- Page 4 2. Lift the cover up to open the chassis. II. To Install SO-DIMM to the board 1. Locate the SO-DIMM slot on the board.
- Page 5 2. Insert the gold-figure side of the compatible SO-DIMM into the slot at a 30 degree angle. See to it that the break of the module fit into the notch of the slot and the golden-finger side should be fully plugged into the slot.
- Page 6 III. To Install M.2 E-Key (2230) PCIe Card 1. Locate the M.2 E-Key PCIe (2230) slot on the board. Prepare compatible M.2 PCIe, type- 2230 card. 2. To install compatible card, please remove the screw post and nut fixed in the marked spot at first.
- Page 7 3. Insert the gold-figure side of the compatible card into the slot and press down. See to it that the golden-finger side should be fully plugged into the slot. 4. Secure the card to the board by tightening up the screw to the marked spot. *Note: The screw post and nut fixed at location MH1 for either installing M.2 E-key type-2230 or M.2 M-key type-2242 card (If you use M.2 M-key type-2242 card, M.2 E-key type-2230 is not available;...
- Page 8 5. Locate the reserved antenna holes on the rear panel. Remove the dust-proof plugs on the marked spots from the panel to install the antenna. 6. Push this antenna screw head into antenna hole of the rear panel from the backside of the panel.
- Page 9 The washer ① & the hexagonal screw nut ②. Push the washer ① through the antenna head. 7. And then lock the antenna screw head to the front side of the rear panel with the hexagonal screw nut② and tighten it up.
- Page 10 8. Press the metal hat on the end of the antenna string to corresponding antenna slot on the card as showed. 9. Repeat step 6 to 8, to finish installation of the other antenna.
- Page 11 10. Connect the external Wi-Fi receiver antenna to the antenna screw head on the rear panel. IV. To Install M.2 M-Key SATA (2242) card 1. Locate the M.2 M-Key SATA (2242) slot on the board. Prepare compatible M.2 SATA, type -2242 card.
- Page 12 2. To install compatible card, please remove the screw in the marked spot at first. 3. Insert compatible M.2 M-Key, type-2242 card into the slot. See to it that the golden-finger side should be fully plugged into the slot.
- Page 13 4. Tighten up the screw removed before to the marked spot to secure the card. *Note: The screw post and nut fixed at location MH1 for either installing M.2 E-key type-2230 or M.2 M-key type-2242 card (If you use M.2 M-key type-2242 card, M.2 E-key type-2230 is not available; vice versa). V.
- Page 14 3. Unlock the reserved screws for VESA mount on the back cover of the monitor. 4. Adjust the chassis with VESA mount rack to the back cover of the monitor and lock it to the monitor by tightening up the above marked screws. 5.
- Page 15 2. Place the rack upon the cover in the direction as the photo shows. Tighten up compatible screws to lock the chassis to the rack. 3. Adjust the chassis with wall mount rack to the wall and lock it to pre-punched holes in the wall by tightening up the above marked screws on the top side.
- Page 16 VII. To Install DIN Rail Mounting Clips 1. Find the DIN rail mounting clip in the attached accessories package. Place the clip upon VSEA mount rack, in the direction as the photo shows. 2. The screw holes on the back side of the clip should match those of the rack, as the photo shows. 3.
Need help?
Do you have a question about the JBC420U11 Series and is the answer not in the manual?
Questions and answers