Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Masalta MFG10 Series
Summary of Contents for Masalta MFG10 Series
-
Page 2: Table Of Contents
■ NEVER operate this equipment under the Ⅰ RULES FOR SAFE OPERATION influence or drugs or alcohol. General Safety …………………………………….1-2 ■ NEVER use accessories or attachments, Diamond Blade Safety ……………………….……..2 which are not recommended by MASALTA Transportation Safety ………………………….……2 this equipment. Damage Emergencies …………………………………………3 equipment and/or injury to user may result. -
Page 3: Diamond Blade Safety
and cleanliness before mounting blade. ■ NEVER use fuel as a cleaning agent. Blade should fit snugly on the shaft and ■ ALWAYS read, understand, and follow procedures in against the inside/outside blade flanges. operator’s Manual before attempting to operate ■... -
Page 4: Emergencies
EMERGENCIES ■ ALWAYS know the location of the nearest fire extinguisher and first aid kit. Know the location of the nearest telephone. Also know the phone numbers of the nearest ambulance, doctor and fire department. This information will be invaluable in the case of an emergency. MAINTENANCE SAFETY ■... -
Page 5: Safety Label
SAFETY LABLES: MASALTA machines use international pictorial labels where needed. These labels are described below: Label Meaning DANGER! Engines emit carbon monoxide; operate only in well-ventilated area. Read the Operation Manual for machine information. No sparks, flames, or burning objects near the machine. -
Page 6: Ⅱ Operation
Label Meaning WARNING! All displacement of the machine outside the cutting area shall be carried out with the tool not in rotation. WARNING! Cutting hazard. Always replace blade guard! of this unit is essential. Read the manual in its Ⅱ OPERATION entirety and follow the instructions carefully. -
Page 7: Blade Removal And Replacement
diamond blade. 3. Outside Blade Flange (Collar) – Ensure that the 6. Use the provided blade nut and blade shaft outside blade flange is placed flush against the locking wrenches to install the diamond diamond blade. The inside surface of the flange must blade. -
Page 8: Stopping The Engine
4. Place the Chock Lever in the “CLOSED” 4. Place the fuel valve lever to the OFF position. position. 5. Rotate the throttle lever halfway between Fast and Slow for starting. All sawing is done at GUARDS, COVERS & V-BELTS full throttle. - Page 9 Ⅲ MAINTAINENACE - TROUBLESHOOTING BLADE TROUBLESHOOTING SYMPTOM POSSIBLE PROBLEM SOLUTION Consult Dealer for correct blade. Try Blade too hard for the material cutting very soft material (sandstone, silica being cut? brick, cinder block) to "Redress" the blade. Engine torque diminished Tighten and/or replace V-Belt.
- Page 10 Ⅲ MAINTAINENACE - TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE SOLUTION Check gap, insulation or replace Spark plug bridging? spark plug. Difficult to start, "fuel is Carbon deposit on spark plug? Clean or replace spark plug. available, but no SPARK at spark Check spark plug insulation, replace Short circuit due to deficient plug".
-
Page 11: Troubleshooting
Ⅲ MAINTAINENACE - TROUBLESHOOTING TROUBLESHOOTING (ENGINE, CONTINUED) SYMPTOM POSSIBLE CAUSE SOLUTION Air cleaner not clean? Clean or replace air cleaner. "Weak in power" Check float adjustment. Improper level in carburetor? compression is Rebuild carburetor. proper and does not misfire. Defective spark plug? Clean or replace spark plug. -
Page 12: Ⅳ Specification
Nameplate: Ⅴ SEPECIFICATION Motor MFG10-3 Petrol, Robin EX17 4.2kw output MFG10-4 Petrol, Honda GX160 4.0kw output Operation Weight MFG10-3 47kgs MFG10-4 50kgs Max. Cutting Depth - - - - - - - - 82.6mm (3.25 in) Acoustic Noise (According to 2000/14/EC) Blade size - - - - - - - - - - - - - - - - - 250mm (10in) MFG10-3/4 Measured sound power level... -
Page 13: Ⅴ Warranty
WARRANTY WARRANTY WARRANTY WARRANTY These products are covered by warranty for a period of six (6) months from the date of purchase against defects in material or workmanship provided that: · The product concerned has been operated and maintained in accordance with the operating instructions. ·... -
Page 14: Ⅶ Ec Declaration
CE-KONFORMITÄTSERKLÄUNG DECLARACIÓN DE CONFORMIDAD DE LA CE DÉCLARATION DE CONFORMITÉ C.E. MASALTA ENGINEERING CO., LTD Weisi Road, Baohe Industrial Estate, HeFei 230051, China hereby certifies that the construction equipment specified hereunder / bescheinigt, da. das Bauger.t / certifica que la máquina de construcción / atteste que le matériel : Category / Art / Categoría / Catégorie:... - Page 15 Distributed By MASALTA ENGINEERING CO., LTD Add: Weisi Road, Baohe Industrial Estate, Hefei 230051, Tel: 86-551-4846601, 4846580 Fax: 86-551-4846616, 4846626 E-mail: sales@masalta.com.cn, masalta@mail.hf.ah.cn http://www.masalta.com.cn Version: 01/09/01...