Table of Contents
Advertisement
Quick Links
R
OPERATION MANUAL
FLOOR SAW MFS 14
!
WARNING
To reduce the risk of injury, all operators and maintenance personnel must read and understand these
instructions before operating, changing accessories, or performing maintenance on Masalta power
equipment. All possible situations cannot be covered in these instructions. Care must be exercised
by everyone using, Maintaining or working near this equipment.
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for Masalta MFS 14
Summary of Contents for Masalta MFS 14
- Page 1 To reduce the risk of injury, all operators and maintenance personnel must read and understand these instructions before operating, changing accessories, or performing maintenance on Masalta power equipment. All possible situations cannot be covered in these instructions. Care must be exercised...
-
Page 2: Table Of Contents
Table of Contents 1. SAFETY INFORMATION. ……………………………………………………………………..2 1.1 Safety Precautions …………………..………………………………………………………. 2 1.2 Operating Safety……………………………………………………………………………. . .3 1.3 Blade Safety …………………………………………………..……………………..………..4 1.4 Transportation Safety …………………………………………………………………………4 1.5 Service Safety …………………………………………………………………………..……. 4 1.6 Safety Labels……………………………..………………….………………….…………...5-6 2. OPERATION ………………………………………………………….….…………….….……... 7 2.1 Controls & Components ………………………………………………...…………………… 7 2.2 Application…………………………………………………………….……………………..……….8 2.3 Operating Principle ………………………………………………………………………………….8 2.4 Assembling the blade .…………………………………………….………………...……..……..8... -
Page 3: Safety Information
SAFETY INFORMATON 1.1 Safety Precautions Before using this equipment, study the entire owner’s manual to become familiar with its operation. Do not allow untrained or unauthorized personnel, especially children, to operate this equipment. Use only factory authorized parts for service. This manual contains DANGER, WARNING, CAUTION callouts which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service. -
Page 4: Operating Safety
■ NEVER operate this equipment when not feeling well due to fatigue, illness or under the influence of drugs or alcohol. ■ NEVER use accessories or attachments, which are not recommended by MASALTA for this equipment. Damage to the equipment and/or injury to user may result. -
Page 5: Blade Safety
SAFETY INFORMATON 1.3 Blade Safety ■ Use appropriate steel centered diamond blades manufactured for use on concrete saws. ■ ALWAYS inspect diamond blades before each use. The blade should exhibit no cracks, dings, or flaws in the steel centered core and/or rim. Center (arbor) hole must be undamaged and true. -
Page 6: Safety Labels
SAFETY INFORMATON Safety Labels MASALTA machines use international pictorial labels where needed. These labels are described below: Label Meaning DANGER! Engines emit carbon monoxide; operate only in well-ventilated area. Read the Operation Manual for machine information. No sparks, flames, or burning objects near the machine. - Page 7 SAFETY INFORMATION Label Meaning WARNING! Hot surface! WARNING! WARNING! Be care of your hand and foot when cutting. WARNING! A nameplate listing the model number and serial number is attached to each unit. Please record the information found on this plate so it will be available if the nameplate lost or damaged.
-
Page 8: Operation
OPERATION 2. OPERATION 2.1 Controls & Components Ref. Description Ref. Description Refueling Trolley wheel Handle for Blade high Adjustment Splash Guard Throttle Control Blade Guard Water Tank Filling Diamond Blade Handle for Operating Pointer Wheel... -
Page 9: Application
OPERATION 2.2 Application Floor saw has been specifically designed as the ideal machine for the professional contractor who is engaged in concrete and asphalt flat cutting. It is the most common type of diamond blade cutting. it is possible to cut both concrete (green or cured, with or without rebar) or asphalt with a floor saw. -
Page 10: Cutting
OPERATION 6. If the engine has started, while listening to explosion sounds, return the choke lever slowly to full-open position. Be sure to perform a warm-up run for the period 3 to 5 minutes at low speed, while paying careful attention to gasoline leakage or abnormal sound. 7. -
Page 11: Maintenance
MAINTENANCE 3. MAINTENANCE 3.1 Blade Removal and Replacement 1. Disconnect the water hose coupler. 2. Ensure the Engine ON/OFF switch on the engine are turned to the “OFF“ position. 3. Place the PMF14 Saw on a stable level working surface. 4. -
Page 12: Troubleshooting
MAINTENANCE 3.4 Troubleshooting 3.4.1 Blade Troubleshooting SYMPTOM POSSIBLE PROBLEM SOLUTION Consult Dealer for correct blade. Try Blade too hard for the cutting very soft material (sandstone, silica material being cut? brick, cinder block) to "Redress" the blade. Engine torque diminished Blade slows Tighten and/or replace V-Belt. -
Page 13: Engine Troubleshooting
MAINTENANCE 3.4.2 Engine Troubleshooting SYMPTOM POSSIBLE CAUSE SOLUTION Check gap, insulation or replace Spark plug bridging? spark plug. Difficult to start, Carbon deposit spark "fuel is Clean or replace spark plug. plug? available, but no SPARK at spark Check spark plug insulation, replace Short circuit due to deficient plug". - Page 14 MAINTENANCE SYMPTOM POSSIBLE CAUSE SOLUTION Fuel not available in fuel Fill with correct type of fuel. tank? No fuel present Fuel filter clogged? Replace fuel filter. at the carburetor. Fuel tank cap breather hole Clean or replace fuel tank cap. clogged? Air in fuel line? Bleed fuel line.
-
Page 15: Transporting
MAINTENANCE 3.5 Transporting 1. Shutdown engine for transportation. 2. The blade must be removed from the saw during all transport and lifting. 3. For transportation, tighten fuel tank cap securely to prevent fuel from spilling. 4. Use the parking brake during transportation 5. -
Page 16: Technical Data
TECHNICAL DATA 4. TECHNICAL DATA Model MFS14-1 MFS14-3 MFS14-4 Engine type Kipor170 Robin EX17 Lombardini LD225 Power kw(hp) 3.1(4.2) 4.2(5.7) 4.0(5.5) Weight kg(lb) 83(183) 70(154) 70(154) Max cutting depth cm(in) 18.5(7.2) Blade size cm(in) 30-35(12-14) Depth adjustment Handle rotation Driving Manual push Water tank capacity (L) Dimension:... -
Page 17: Warranty
WARRANTY MASALTA products are covered by warranty for a period of twelve (12) months from the date of purchase against defects in material or workmanship provided that: The product concerned has been operated and maintained in accordance with the operating instructions. -
Page 18: Maintenance Record
MAINTENANCE RECORD PREVENTATIVE MAINTENANCE AND ROUTINE SERVICE PLAN MASTERPAC green concrete saw has been assembled with care and will provide years of service. Preventative maintenance and routine service are essential to the long life of your saw. After reading through this manual thoroughly, you will find that you can do some of the regular maintenance yourself. -
Page 19: Ec Declaration
CE-KONFORMITÄTSERKLÄUNG DECLARACIÓN DE CONFORMIDAD DE LA CE DÉCLARATION DE CONFORMITÉ C.E. MASALTA ENGINEERING CO., LTD Weisi Road, Baohe Industrial Estate, HeFei 230051, China hereby certifies that the construction equipment specified hereunder / bescheinigt, da. das Bauger.t / certifica que la máquina de construcción / atteste que le matériel : Category / Art / Categoría / Catégorie:... - Page 20 Distributed By MASALTA ENGINEERING CO., LTD Add: 20 Dalian Road, Baohe Industrial Estate, Hefei, China Tel: 86-551-64846601, 64846580 Fax: 86-551-64846616, 64846626 E-mail: sales@masalta.com.cn, masalta@mail.hf.ah.cn Http://www.masalta.com.cn Version: 01/15/01...
Need help?
Do you have a question about the MFS 14 and is the answer not in the manual?
Questions and answers