Filter Replacement - TESY AC 96 HCIUV Usage And Storage Instructions

the others do not light up.
EN
In the standby state, touch the "switch" button, the
"switch" button displays green, and the default enters
Power
the "automatic" mode.
Button
a. Boot, light detection is off by default, only in the
automatic mode, long press "sleep button + timing
button" 3S, turn on the light detection mode,
Automatic
b. After the light detection mode is turned on, after
Button
30 seconds in the automatic mode (the running time
is not within this 30 seconds), when the light is weak,
enter the "automatic sleep" mode, only the automatic
button and the sleep button are on, and the other
displays are off. When the light is strong, the "auto
sleep" mode is exited, and the previous mode and
state are restored.
C. When "Auto Sleep" is active, the [sleep] button light
and [Auto button light are simultaneously lit green
(used to distinguish between "auto sleep" mode and
"manual sleep" mode), and other lights are turned off.
d. When "Auto Sleep" is valid, press any key alone to
temporarily exit (after pressing the key, the light is
weak after 30 seconds, and then enter the automatic
sleep mode again.
e. When the light detection is turned on, only in the
automatic mode or the automatic sleep mode, long
press the "sleep button + timing button" 3S to exit
the light detection mode.
f. When the light detection is turned on, the power
is turned off again, and the light detection mode is
exited by default.
When the power is turned on by default, the smart
mode is turned on, and the gear position will change
automatically during the running. Touch this button
Wind
to exit the smart mode, and the wind speed button
Speed
small icon Light up, the digital display shows the cur-
Button
rent wind speed gear position, continuously operate
this button, the wind speed gear position is: 2->3->
4->5->1->2. Cycle switching, stop the PM2.5 value
display and returned after 3 seconds of operation.
Touch this button in the running state to enter the
sleep mode, the product runs at a low speed state,
and the timing is effective after entering sleep. If
Sleep
you press other function buttons at this time, exit
Button
the sleep mode and return to the normal working
setting mode.
In the power on or standby state, touch the "Timer" but-
ton, one button sound, the digital display shows the
timing time and the
Timer
button is illuminated. Тhe touch button is effective within
Button
3 seconds, the timing time can be changed, by pressing
the "Timer" button again. When there is a set time, press
and hold the time button for 3 seconds to cancel the
timing function.
In the power-on state, the child lock button indicator does
not light, long press the "child lock" button for 3 seconds
to open the child lock function, when the child lock is
Child Lock
Button
activated,
tons are invalid. Press and hold the "child lock" for 3
seconds to exit the child lock function, and the
indicator is off. (Only in the power on state Under can
open or close the child lock)
This button is to control the LED lamp. Touch it to switch
off/ on the LED light.
LED light
Button
When under auto mode, press "SLEEP" and "TIMER" button
3s, on/off the light mode.
a.When turn on the light mode, after 30s, the device will
+
only adjust the mode between sleep or auto mode auto-
matically according to the current ambient light, when
light is brightness, turn on auto mode, when darkness,
turn on sleep mode.
Sleep +
b.The device is starting running as light function is off.
Timer =
c.Under light mode, press "SLEEP"+ "TIMER" button to
Light
turn off the light mode, or reboot the device to off the
Button
light mode.
10
Instructions for use and maintenance
indicator light of the timing
The indicator light is on, all the touch but-
Indication Particulate Matter (PM2.5)
Color PM2.5 Concentration
Indicator
blue PM2.5≤50mg/m³
green 51≤PM2.5≤100mg/m³
yellow 101≤PM2.5≤150mg/m³
red PM2.5>151mg/m³
Duping and opening safety protection:
1. The device will stop working automatically for safety
protection when open the right & left door or slop over 30
degree.
2. The device will re-work normal when close the
right&left door or turn back to horizontal position.

FILTER REPLACEMENT

"Speed" + "Auto" = "Filter reset button"
When the filter life is out, the "ON/OFF" button will shining
and with "di di di" sound to reminder users to replace the
new filter.
1. When filter life is out of time, press "SPEED"+ "AUTO"
button 3s to reset the filter life, the "ON/OFF" button will
stop shining and sound after reset the filter life.
2. When filter life is not out of time, press "SPEED"+
"AUTO" button 10s to force to reset the filter life.
3. The device filter life is setting as 3000 hours, record
by each hour.
• Shut down and power off the main unit.
Note: Turn on the air to turn off the air purifier. The air
purifier is in standby mode. You need to unplug the power
plug to cut off the power of the main unit.
• Open the lid cover, catch the button of the lid cover, and
pull it out.
Air Quality
Excellent
Good
Poor
Extremely Poor