Download Print this page

Litepanels GEMINI 2X1 HARD Series User Manual

Studio full color lensed panel led fixture

Advertisement

Quick Links

STUDIO FULL COLOR LENSED PANEL LED FIXTURE (940-2001)
SAFETY INFORMATION
To clean the GEMINI 2X1 HARD, wipe with a clean, dry, non-abrasive cloth only.
Weight (including Yoke, not including accessories): 12.3 kg [27.1 lb]
Dimensions (including Yoke, not including accessories): W = 74.8 cm [29.4 in], H = 52.9 cm [20.8 in], D = 17.6 cm [6.9 in]
Do not restrict air flow around the GEMINI 2X1 HARD. Keep the fixture's air intakes and air exhaust space clear of obstruction.
Plug the GEMINI 2X1 HARD into a mains electrical outlet using only a provided AC powerCON power cable or one specified by Litepanels
pinching, twisting, or crushing. Use a mains electrical outlet that is grounded and rated for 100-240VAC, 50/60Hz only.
Do not use, mount, transport, or store the GEMINI 2X1 HARD near radiators, space heaters, ovens, stoves, heat registers, open flame, or any heat source, or in an
environment with an ambient temperature greater than 65°C [149° F].
The GEMINI 2X1 HARD is suitable for operation only in an environment as follows: ambient air temperature between -20°C and 45°C [between -4°F and 113°F]; less
than 85% relative humidity (RH), no condensation. Use in a dry environment; do not place on a wet surface or submerge the GEMINI 2X1 HARD in liquid.
WARNING: Tampering with or disassembling the GEMINI 2X1 HARD may result in electric shock and will void the manufacturer's warranty.
WARNING: To reduce the risk of electric shock or fire, do not expose the GEMINI 2X1 HARD to rain, moisture, or liquids.
Immediately consult with qualified Litepanels
has been damaged; the fixture has been exposed to rain, moisture, or liquid; or the fixture does not operate normally.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
INCLUDED
GEMINI 2X1 HARD Light Fixture
GEMINI 2X1 HARD Yoke
Ultra Light Diffuser
Domed Diffuser
Hex L-Key, 6mm (not pictured)
D
A
B
C
(A)
DIFFUSER LATCH (2X)
(B)
DIFFUSER FLAP
(C)
YOKE
(D)
TILT LOCK SCREW
(E)
AIR INTAKE
(F)
ANTENNA
(G)
UNIVERSAL COMMS PORT
(H)
USB PORT
(I)
TILT LOCK KNOB
(J)
1/4-20 FEMALE THREAD (2X)
(K)
AIR EXHAUST
(L)
DOVETAIL CHANNEL (2X)
service personnel if any of the following have occurred: The fixture has been dropped or impacted; the power cable
®
E
A
O
R
Q
T
N
S
M
P
(M)
MAINS AC POWER INPUT
(N)
MAINS AC POWER THROUGH
(O)
3-PIN XLR DC POWER INPUT JACK
(P)
ACTIVE COMMS INDICATOR LIGHT
(Q)
5-PIN XLR DMX / MASTER/REPLICA INPUT
(R)
5-PIN XLR DMX / MASTER/REPLICA OUTPUT
(S)
RJ45 DMX / MASTER/REPLICA INPUT
(T)
RJ45 DMX / MASTER/REPLICA OUTPUT
(U)
DISPLAY
(V)
CANCEL BUTTON
(W)
PRESET BUTTONS (6X)
(X)
PRESET TOGGLE BUTTON
F
E
H
G
V
W
U
Z
AB
Y
AA
AC
(Y)
(Z)
(AA)
(AB)
(AC)
(AD)
(AE)
www.litepanels.com
. Protect the cable from
®
I
J
E
X
AD
GREEN OFFSET / HUE / MENU KNOB
CCT / SATURATION KNOB
DIMMER / INTENSITY KNOB
POWER / STATUS INDICATOR LIGHT
ON / OFF SWITCH
STANDARD JUNIOR PIN
ACCESSORY LATCH
SEE REVERSE
K
L
AE

Advertisement

loading

Summary of Contents for Litepanels GEMINI 2X1 HARD Series

  • Page 1 Do not restrict air flow around the GEMINI 2X1 HARD. Keep the fixture’s air intakes and air exhaust space clear of obstruction. Plug the GEMINI 2X1 HARD into a mains electrical outlet using only a provided AC powerCON power cable or one specified by Litepanels .
  • Page 2 If the Power/Status Indicator Light (“AB”) turns red, flashes red, and/or the light fixture does not operate normally, navigate the menu to SETTINGS -> SYSTEM -> SYSTEM MONITOR to identify active warning or fault conditions. If warning or fault conditions persist, contact litepanels.com/support...

This manual is also suitable for:

940-2101940-2111940-2201940-2211940-2301940-2311 ... Show all