Table of Contents
Advertisement
Available languages
Available languages
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
WARNING: To reduce the risk of injury, read the
instruction manual.
Intended Use
This inflator is intended soley for high‑flow inflation of rafts,
air mattresses, swimming pool floats, etc. This product is
intended for household, consumer use only.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
WARNING: Read all safety warnings and instructions
provided with this attachment and the Power Unit
BDCDMT120 before using this attachment
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert
symbols and words to alert you to hazardous situations and
your risk of personal injury or property damage.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury.
(Used without word) Indicates a safety
related message.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
property damage.
ADDITIONAL SAFETY WARNINGS FOR
YOUR INFLATOR
WARNING: Keep hair, jewelry, and loose clothing away
from vents, openings, and deflator port.
WARNING: FOR HOME AND CAR USE ONLY: Inflate
rafts, swimming pool floats, air mattresses, and more
in and around the home. Recommended maximum
continuous duty at 65 psi is 2 minutes on with
5 minutes off.
WARNING: RISK TO BREATHING.The compressed
air from your inflator is not safe for breathing. Never
inhale air from your inflator or from a breathing device
connected to the inflator.
WARNING: DO NOT direct inflator port towards face.
WARNING: DO NOT block inflation port when
inflating or deflating.
WARNING: DO NOT place fingers or other objects in
the inflator port hole.
WARNING: Ensure the deflator port is not obstructed
when in use.
WARNING: RISK OF BURSTING. Too much air
pressure causes a hazardous risk of bursting. Check the
manufacturer's maximum pressure rating for objects
being inflated.
WARNING: RISK OF BURSTING. Do not leave inflator
running unattended.
WARNING: RISK OF FIRE: Inflator can become hot
during use. Allow inflator to cool 30 minutes before
storing away.
CALIFORNIA PROPOSITION 65
WARNING: This product or its power cord contains
lead, a chemical known to the State of California to
cause cancer and birth defects or other reproductive
harm. Wash hands after handling
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories, when
replacing line, or prior to cleaning. An accidental
start‑up can cause injury.
Attaching and Removing Nozzles (Fig. A, B)
•
To attached a nozzle (
on the nozzle with the pins
Once fully on, turn the nozzle clockwise.
•
To remove, turn the nozzle counterclockwise fully and
slide the nozzle off.
•
After removing the nozzle, place it in the nozzle storage
Wh ...................... watt hours
Ah ....................... amp hours
or AC ........... alternating current
or AC/DC .... alternating or direct
current
...................... Class II Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all
documentation
6
,
7
,
8
), line up the notches
4
on the inflator port
English
9
2
.
10
.
3
Advertisement
Table of Contents
