Sealey CP20VTP Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
1.1. BATTERY SAFETY INSTRUCTIONS (BATTERY NOT INCLUDED)
WARNING! Battery contains Lithium-ion which is dangerous. Handle with care to avoid damage, fire, corrosion or personal injury.
‰
Charge battery prior to its first use. The battery will have been shipped in a low charge state. To reduce the risk of burns or fire:
9
DO NOT attempt to open, disassemble, modify or service the battery pack.
8
DO NOT crush, puncture, short external contacts or dispose of in fire or water.
8
DO NOT expose to temperatures above 40°C (104°F).
8
Replace only with the battery pack designated for this product.
9
Use only the charging base provided to charge the tool.
9
Remove the battery if the tool is not to be used for a period of time.
9
Keep the battery terminals and grooves free from wood chips, sawdust or soil.
9
DO NOT allow the battery to become fully discharged.
8
Recharge the battery when you notice the tool has less power.
9
DO NOT recharge a fully charged battery. Overcharging shortens the batteries service life.
8
Charge the battery at a room temperature between 5ºC to 45ºC.
9
Charge the battery if tool has not been used for 6 months.
9
DO NOT attempt recharging the battery by means of an engine generator or a DC power source.
8
WARNING! Dispose of spent batteries correctly as they contain Lithium-ion. DANGER! DO NOT attempt to disassemble the
‰
battery. For safety and environmental reasons DO NOT discard in domestic waste or by burning. ONLY discard or recycle according
to local authority regulations.
WARNING! DO NOT allow a leaking battery to contact your person.
‰
1.2. GENERAL SAFETY
WARNING! Ensure that Health & Safety, local authority
‰
and general workshop practice regulations are adhered to
when using this equipment.
Familiarise yourself with the applications, limitations and
9
potential hazards peculiar to the tool.
WARNING! Disconnect the battery before changing
‰
accessories, servicing or performing any maintenance.
Maintain the tool in good condition (use an authorised
9
service agent).
Replace or repair damaged parts. Use genuine parts only.
9
Unauthorised parts may be dangerous and will invalidate
the warranty.
Keep the work area clean, uncluttered and ensure that
9
there is adequate lighting.
Keep the tool clean for best and safest performance.
9
Maintain correct balance and footing. Ensure the floor is
9
not slippery and wear non-slip shoes.
Remove ill fitting clothing. Remove ties, watches, rings and
9
other loose jewellery and contain, and/or tie back, long hair.
Keep children and unauthorised persons away from the
9
work area.
DO NOT use the tool for any purpose other than that for
9
which it is designed.
DO NOT operate the tool if any parts are damaged or
8
missing.
DO NOT get the tool wet or use in damp or wet locations or
8
areas where there is condensation.
DO NOT allow untrained persons to operate the tool.
8
DO NOT operate tool when you are tired or under the
8
influence of alcohol, drugs or intoxicating medication.
© Jack Sealey Limited
CORDLESS 20V TELESCOPIC POLE FOR
CP20VPSH/CP20VPHT
CP20VTP
MODEL NO:
CP20VTP
CP20VPSH
CP20VPHT
Original Language Version
(sold separately)
(sold separately)
CP20VTP Issue 1 25/10/21