Table of Contents
Advertisement
World Time
World Time digitally displays the current time in
Current time in the zone
of the selected city code
30 cities (29 time zones) around the world.
• For full information on city codes, see the "City
Code Table".
• All of the operations in this section are
performed in the World Time Mode, which you
enter by pressing D.
Timekeeping Mode time
To view the time in another city
In the World Time Mode, use C (east) and A (west) to scroll through city
codes (time zones).
• When the currently selected time zone is one that includes mostly ocean, a
value indicating the zone's Greenwich Mean Time differential appears in
place of a city code.
• If the current time shown for a city is wrong, check your Home City time
settings and make the necessary changes.
To toggle a city code time between Standard Time and Daylight
Saving Time
1. In the World Time Mode, use C (east) and A
(west) to display the city code (time zone)
whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down E to toggle between Daylight
Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).
• The DST indicator appears on the display
whenever you display a city code for which
Daylight Saving Time is turned on.
• You cannot toggle between Daylight Saving Time and Standard Time if the
displayed city code is GMT.
• Note that the DST/Standard Time setting affects only the currently
displayed city code. Other city codes are not affected.
Stopwatch
The stopwatch lets you measure elapsed time,
1/100
Minutes
split times, and two finishes.
second
• The display range of the stopwatch is 9 hours,
Hours
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from
zero after it reaches its limit, until you stop it.
• The stopwatch measurement operation
continues even if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is
frozen on the display clears the split time and
returns to elapsed time measurement.
• All of the operations in this section are
Seconds
performed in the Stopwatch Mode, which you
Timekeeping
enter by pressing D.
Mode time
To measure times with the stopwatch
Elapsed Time
C
C
C
Start
Stop
Re-start
Split Time
C
A
A
Start
Split
Split release
sj
(
displayed)
Two Finishes
C
A
C
Start
Split
Stop
First runner
Second runner
finishes.
finishes.
Display time
of first runner.
Operation Guide 3043
C
A
Stop
Clear
C
A
Stop
Clear
A
A
Split release
Clear
Display time of
second runner.
Countdown Timer
You can set a countdown timer start time in the
Seconds
Minutes
range of one minute to 60 minutes. An alarm
sounds when the countdown reaches zero. An
auto-repeat feature causes the countdown to
restart automatically when the end of a
countdown is reached, and a progress beeper
signals the progress of the countdown.
• All of the operations in this section are
performed in the Countdown Timer Mode,
which you enter by pressing D.
Configuring the Countdown Timer
Timekeeping
Mode time
The following are the settings you should
configure before actually using the countdown
timer.
• Countdown start time
• Auto-repeat on/off
• Progress beeper on/off
Countdown start time
You can set a countdown start time in the range of one minute to 60 minutes,
in one-minute increments.
Auto-repeat
Whenever zero is reached, the watch beeps and auto-repeat automatically
restarts the countdown from the countdown start time you set. When the
countdown reaches zero while auto-repeat is turned off, the watch will beep
and then display the countdown start time (without restarting the countdown).
Auto-repeat will repeat up to 10 times.
Progress Beeper
When the progress beeper is turned on, the watch beeps at minute 10, 5, 4,
3, 2, and 1 of the countdown, and at second 50, 40, 30, 20, 10, 5, 4, 3, 2, and
1 of the final minute of the countdown.
To configure countdown start time and auto-repeat settings
1. While the countdown start time is on the
display in the Countdown Timer Mode, hold
down E until the minute setting of the
countdown start time starts to flash, which
indicates the setting screen.
• If the countdown start time is not displayed,
use the procedure under "To use the
countdown timer" to display it.
2. Press D to toggle between the countdown
starting time setting screen and the auto-
repeat setting screen.
3. Perform the following operations, depending on which setting is currently
selected on the display.
• While the minute setting is flashing, use C (+) or A (–) to change it.
• While the auto-repeat on/off setting (
display, press C to toggle auto-repeat on (
4. Press E to exit the setting screen.
To turn the progress beeper on and off
Pressing A while the countdown start time is on
Progress beeper on
the display or while a countdown timer operation
indicator
is in progress in the Countdown Timer Mode
toggles progress beeper operation on (
displayed) and off (
To use the countdown timer
Press C while in the Countdown Timer Mode to start the countdown timer.
• When the countdown reaches zero, the alarm sounds for five seconds or
until you stop it by pressing any button.
• Press C while a countdown operation is in progress to pause it. Press C
again to resume the countdown.
• The countdown timer operation continues even if you exit the Countdown
Timer Mode.
• To stop a countdown operation completely, first pause it (by pressing C),
and then press A. This returns the countdown time to its starting value.
• Frequent use of auto-repeat and the alarm runs down the battery.
or
) is flashing on the
) and off (
).
not displayed).
8
Hide quick links:
Advertisement
Table of Contents
