Table of Contents
Advertisement
Quick Links
Model# 80213
SKU#: 1001-651-809
USE AND CARE GUIDE
VENTILATION FAN WITH LED LIGHTS
Questions, problems, missing parts? Before returning to the store,
call Hampton Bay Customer Service
8 a.m.- 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
1-855-HD-HAMPTON
HAMPTONBAY.COM
THANK YOU
We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this ventilation fan. We strive to continually
create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement
needs. Thank you for choosing Hampton Bay!
Advertisement
Table of Contents
Related Manuals for HAMPTON BAY 80213
Summary of Contents for HAMPTON BAY 80213
- Page 1 THANK YOU We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this ventilation fan. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement...
-
Page 2: Table Of Contents
9.When cutting or drilling into wall(s) or ceiling, do not damage electrical wiring or other hidden utilities. TE: Proper installation of insulation around and over 10.This unit must be grounded. fan body to minimize building heat loss and gain. 80213 R44038... -
Page 3: Warranty
Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of five years after the date of purchase by the original purchaser. Hampton Bay also warrants that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser. -
Page 4: Installation Options
Pre-installation (continued) PLANNING FOR SUCCESSFUL INSTALLATION (continued) CAUTION: To avoid motor bearing damage and CAUTION: DO NOT install this product in a wall. This noisy/unbalanced impellers, keep drywall spray, product is designed for installation in ceilings up to a 12/12 construction dust, etc. -
Page 5: Tools Required
Pre-installation continued) TOOLS REQUIRED Safety Phillips Slotted Hammer goggles screwdriver screwdriver Electrical tape Drill Level Ruler Pencil Wrench MATERIALS REQUIRED Duct Duct vent Duct tape Duct piping clamp HARDWARE INCLUDED NOTE: Hardware not shown to actual size. A A A A A A C C C C C Part... -
Page 6: Package Contents
Pre-installation (continued) PACKAGE CONTENTS Part Description Part Description Mounting Rail Grill Housing Grill Nut Wiring Cover Glass Dome Wiring Cover Screw Dome Cover Motor Finial Motor Screw Watt E-26 LED bulbs ON for further assistance. - Page 7 Installation 4. Remove packing material. NOTE: Estimated assembly time: 30 to 60 minutes. Remove all packing materials before installation. 1. Turn off the power source. 5. Remove the pre-loaded screw tip covers. 2. Loosen the motor screws (F) from the motor (E) and housing (B).
- Page 8 Installation (continued) 7. Remove the wiring cover screw (D). 9. Pop out the first wiring access slug. Use second if needed. 10. Insert the strain relief (BB) into the housing and 8. Remove the wiring cover (C). secure with the washer (CC). Choose Installation Option For New Construction - attaching to joist go to step A, page 9.
-
Page 9: New Construction - Attaching To Joist
Installation (continued) A. NEW CONSTRUCTION - ATTACHING TO JOIST A11. Position the correct depth mark at the bottom A13. Route wires through the strain relief. of the joist based on the thickness of your sheetrock. A12. Screw pre-loaded screws into the joist or framing. A14. - Page 10 Installation (continued) A15. Install the wiring cover (C) using the wiring cover A18. Reinstall the motor (E) by inserting the tabs and screw (D). Make sure wiring connections are inside the pushing up into position. Make sure the wires are not box or under the wiring cover (C).
-
Page 11: New Construction - Suspended Between Joist
Installation (continued) A21. Test the motor. If the motor does not run, check B. NEW CONSTRUCTION - SUSPENDED BETWEEN the plug connection. JOIST B11. Slide the mounting rails (A) into the brackets on the housing (B). B12. Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. - Page 12 Installation (continued) B14. Drill a hole in the center of each outline. B17. Tighten the screws. B15. Insert screws, leaving space between the screw head and the joist. Screws are not provided. B18. Route wires through the strain relief. B16. Attach the rails (A) onto the screws.
- Page 13 Installation (continued) B19. Connect wires as shown using the wire nuts (AA). B20. Install the wiring cover (C) using the wiring cover B22. Connect the wiring harness. DO NOT ALLOW THE screw (D). Make sure all wiring connections are inside MOTOR TO HANG FROM THE WIRING HARNESS.
- Page 14 Installation (continued) B24. Secure the motor by tightening the two screws (F). B25. Turn on the power source. B26. Test the motor. If the motor does not run, check the plug connection.
-
Page 15: Existing Construction - Accessible From Above
Installation (continued) C. EXISTING CONSTRUCTION - ACCESSIBLE FROM ABOVE C11. Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (8"x8 1/2"). Use the motor housing as a template to mark position. Cut out an opening for the housing. - Page 16 Installation (continued) C14. Mark the position of the screws by using holes as a template. C17. Attach the rails (A) onto the screws. C18. Tighten the screws. C15. Drill a hole in the center of each outline. C19. Connect 4" duct and vent to the outside. Tape C16.
- Page 17 Installation (continued) C20. Route wires through the strain relief. C21. Tighten the strain relief screws. C22. Connect wires as shown using the wire nuts (AA). C23. Install the wiring cover (C) using the wiring C24. Connect the wiring harness. DO NOT ALLOW cover screw (D).
- Page 18 Installation (continued) C25. Reinstall the motor by inserting the tabs and C28. Test the motor. If the motor does not run, check pushing up into position. Make sure the wires are not the plug connection. pinched between the motor and the housing. C26.
-
Page 19: Existing Construction - Accessible From Below
Installation (continued) D. EXISTING CONSTRUCTION - ACCESSIBLE FROM BELOW D11. Remove an existing fan and check to make sure D14. Attach existing ducting to duct connector. Tape the opening is large enough to accommodate the new joints. If ducting does not fit securely, an adapter may motor housing (8"x8 1/2"). - Page 20 Installation (continued) D16. Connect wires as shown using the wire nuts (AA). D17. Install the wiring cover (C) using the wiring D19. Reinstall the motor (E) by inserting the tabs and cover screw (D). Make sure all wiring connections pushing up into position. Make sure the wires are not are inside the box or under the wiring cover (C).
-
Page 21: Attaching The Grill
Installation (continued) E. ATTACHING THE GRILL D21. Turn on the power source. E1. Remove the grill nuts (H) from the housing (B). D22. Test the motor. If the motor does not run, check the plug connection. E2. Connect the wiring harness. DO NOT ALLOW THE FIXTURE TO HANG FROM THE WIRING HARNESS. - Page 22 Installation (continued) E4. Attach the grill nuts (H). E7. Secure the glass dome (I) into position against the fixture using the dome cover (J) and finial (K). WARNING: To reduce the risk of electrical shock, all 4 grill nuts MUST be properly installed. E8.
-
Page 23: Care And Cleaning
Solution The fan does not come on. Hampton Bay ventilation fans are extremely quiet. To confirm that the fan is running, place your hand near the vents to feel the air movement. Turn power on, replace fuse, or reset breaker. -
Page 24: Service Parts
Service Parts Part Number 95044-01-000 95029-01-000 77481-01-000 03242-01-133 98037-05-000 65222-01-133 99751-01-000 75184-01-133 97266-02-000 G0166-01-214 67324-01-214 If you need parts or service assistance, please call 1-855-HD-HAMPTON or visit us at our web site at http://www.HAMPTONBAY.com . ON for further assistance. - Page 25 Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service 8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-855-HD-HAMPTON HAMPTONBAY.COM Retain this manual for future use...