1. Manuals
  2. Brands
  3. ICP DAS USA Manuals
  4. Touchscreen
  5. TPD-433-M2
  6. Quick start manual

ICP DAS USA TPD-433-M2 Quick Start Manual

Hide thumbs Also See for TPD-433-M2:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
What's in the box?
Thanks for buying ICPDAS TPD-433-M2 device. This shipping
package contains the following items:
TPD-433-M2 x 1
Back Piece x 1

Related Information

If you are new to TPD-433-M2, please read the "Chapter 3. Getting
Started" of the TouchPAD Hardware User Manual for detailed
information about install the free development tool – HMIWorks and
how to create your first project.
Documents, such as the User Manuals, the API References,
etc.:
http://ftp.icpdas.com/pub/cd/touchpad/document/
Free Development Software, HMIWorks v2.10.10 or above:
http://ftp.icpdas.com/pub/cd/touchpad/setup/
If you have any questions, please feel free to contact us via email.
Technical support:
TPD-433-M2 Quick Start
service@icpdas.com
Quick Start x 1 (This Document)
Round Head Screws x 2
v1.1, Jan. 2019
P1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TPD-433-M2 and is the answer not in the manual?

Questions and answers

Related Manuals for ICP DAS USA TPD-433-M2

Summary of Contents for ICP DAS USA TPD-433-M2

  • Page 1 Back Piece x 1 Round Head Screws x 2 Related Information If you are new to TPD-433-M2, please read the “Chapter 3. Getting Started” of the TouchPAD Hardware User Manual for detailed information about install the free development tool – HMIWorks and how to create your first project.
  • Page 2 Appearance Front View Rear View LED Indicator Ethernet Serial Port 4.3” TFT LCD with Touch Panel Rotary Switch Pin Assignments Description F.G. Frame Ground. F.G. is connected to the inside EMI or ESD suppression circuits. Make sure that F.G. is connected to the Earth DC input Voltage (range: +12 V ~ +48 V) Connected to the power supply’s ground pin...
  • Page 3 255.255.0.0 Gateway 192.168.0.1 First Use of the TPD-433-M2 1. Connect wires as the below figure or prepare an Ethernet cable which will be used to supply power through PoE if there’s a RJ-45 Ethernet port on it. And set the rotary switch to 0 (At this point, the power is not yet supplied).
  • Page 4 3. Try to touch on the icons on the bottom-right corner of the screen of the TPD-433-M2 and you can find that TPD-433-M2 switches to the setting pages. Hardware Installation...
  • Page 5 檢查配件 感謝您購買泓格的 TPD-433-M2 產品。產品包裝內應包含下列配件: 產品須知 x 1 (本文件) TPD-433-M2 x 1 面板蓋 x 1 圓頭螺絲 x 2 參考資訊 如果您是第一次使用 TPD-433-M2，請參閱 TouchPAD 硬體使用手 冊的 “第 3 章 啟動 TouchPAD” 來了解如何安裝免費的開發軟體 HMIWorks 並建立第一個專案以及更多詳細的相關資訊。 相關文件，如使用手冊、應用程式介面指南(API Reference) 等:  http://ftp.icpdas.com/pub/cd/touchpad/document/ 免費開發軟體，HMIWorks 版本 2.10.10 或以上版本: ...
  • Page 6 外觀 前配置圖 後配置圖 LED 指示燈 序列埠 Ethernet 4.3 吋觸控液晶螢幕 旋轉開關 腳位定義 說明 機架接地，F.G. (連接到內部的 EMI 或 ESD 保護電路)， F.G. 請接到大地 直流電壓輸入 (範圍：+12 V ~ +48 V) 連到電源的接地端 RS-485 網路的正訊號線 RS-485 網路的負訊號線 接地端 RS-232 的傳送資料腳位 TxD2 RS-232 的接收資料腳位 RxD2 Technical support: service@icpdas.com...
  • Page 7 強制更新，當 TouchPAD 上的程式嚴重 Ethernet 毀損時可用此模式透過 Ethernet 更新。 Force Update 執行程式。 Run Only Force 透過 USB 更新程式。 Update 網路設定出廠預設如下表: IP Address 192.168.255.1 Subnet Mask 255.255.0.0 Gateway 192.168.0.1 第一次使用 TPD-433-M2 1. 如下圖所示，將電源和接地線連接完成。或是有 RJ-45 的乙太網路接 孔，可以準備一條網路線，透過乙太網路供電 (PoE)。然後將旋轉開關 (Rotary Switch) 轉到 0 (此時尚未供電)。 Technical support: service@icpdas.com...
  • Page 8 乙太網路供電 VDC (+12-+48 V) 外部供電器 使用一字起子來配置旋轉開關 2. 開始供電給 TPD-433-M2，等待約數秒的 開機時間，接著可以看到 TPD-433-M2 執行 出貨預附的程式如左圖所示。 3. 試著按一下 TPD-433-M2 螢幕上面的圖示，TPD-433-M2 會切到其他 的頁面。 硬體安裝 安裝於明盒 安裝於暗盒 安裝於暗盒 安裝於暗盒 EWB-T43F (選購) OB140F (選購) OB140FP (選購) OB120 (選購) Technical support: service@icpdas.com...

Table of Contents