Penguin RTM-ATCA-F140 Quick Start Manual

Penguin Edge™
RTM-ATCA-F140
Quick Start Guide
P/N: 6806800P18D JUNE 2022
1 Box contents
Make sure you receive all items of your shipment:
• One Penguin Edge™ RTM-ATCA-F140 blade
• One printed copy of Quick Start Guide (this document)
• One printed copy of Safety Notes Summary
• Other items that were ordered.
When installing or servicing the system or accessories,
strictly observe the safety precautions in the Safety Notes
Summary. Ignoring these instructions can void the
system warranty and cause personal injury or property
damage.
2 ESD
Electrostatic discharge and incorrect installation or
removal of the card can damage circuit or shorten its
life.
Use a properly grounded ESD wrist strap or make work
in an ESD-safe environment.
Connect to the ESD connector at the front or the rear of
the system.
3 Site preparation
Make sure that all environmental and power requirements defined in
the Penguin Solutions RTM-ATCA-F140 Installation and Use
manual are met.
Operating temperatures refer to the temperature of the air circulating
around the blade and not to the actual component temperature.
4 Install the RTM
Note: The following procedure assumes that your system is
powered. If your system is unpowered, you can disregard the
blue LED and thus skip the respective step.
1. Visually inspect the RTM and zone 3 connectors on the front
blade for damage or bent pins before attempting to insert a
board. If any connector damage or pin damage is observed,
stop before inserting the RTM and send the damaged item
through proper repair channels.
2. If the corresponding front blade is already installed, perform the
following steps. Otherwise skip to step 3.
– On the front blade, verify the face plate screws that secure the
blade to the shelf are tight.
– Deactivate the front blade. Unlatch the lower handle by
squeezing the lever and the latch together and turning the
handle outward only enough to unlatch the handle from the
face plate. Do not rotate the handle fully outward.
– When the blue LED on the front blade is permanently
illuminated, proceed to the next step.
3. Ensure that the top and bottom ejector handles on the RTM are
in the outward position by squeezing the lever and the latch
together.
4. Insert the RTM into the shelf by placing the top and bottom
edges of the RTM in the card guides of the shelf. Ensure that the
guiding module of the front blade and RTM are aligned properly.
5. Apply equal and steady pressure to the RTM to carefully slide
the RTM into the shelf until you feel resistance. Continue to
gently push the RTM until the connectors engage.
6. Squeeze the lever and the latch together and hook the lower and
the upper handle into the shelf rail recesses.
7. Fully insert the blade and lock it to the shelf by squeezing the
lever and the latch together and turning the handles towards the
face plate.
8. Tighten the face plate screws which secure the RTM to the shelf.
9. If the front blade has already been installed (as in step 2),
activate the front blade by squeezing its lower lever and latch
together and press it back into the face plate.
10. If the front blade has not been installed, proceed with the
installation instructions in the front blade installation and use
manual.
Note: Make sure that the handles of both the RTM and the front
blade are closed in order to power up the blade and RTM
payload.
When the blue LED of the RTM is switched OFF and the green
LED OK is switched ON, indicates that the payload of the RTM
has been powered up and that the RTM is active.
11. Connect cables to the face plate, if applicable.
5 Removing the RTM
The following procedure assumes that your system is powered. If
your system is unpowered, you can disregard the blue LED and skip
the respective step.
1. On the front blade, unlatch the lower handle by squeezing the
lever and the latch together and turning the handle outward
only enough to unlatch the handle from the face plate. Do not
rotate the handle fully outward.
2. Wait until the front board blue LED is illuminated permanently.
Note: If the LED continues to blink, a possible reason may be
that upper layer software rejects the blade extraction request.
3. Remove face plate cables, if applicable.
4. Unfasten the screws of the RTM face plate until the RTM is
detached from the shelf.
5. Unlatch the RTM upper and lower handles and rotate fully
outward.
6. Remove the blade from the shelf.