Table of Contents
Advertisement
Quick Links
INSTRUCTIONS
BX-UCB
U-HSTR2
CONTROL BOX
HAND SWITCH
Optical Microscope Accessory
This instruction manual is for the Olympus Control Box model BX-UCB and Hand Switch model U-
HSTR2, both for use with the BX2 motorized microscope. To ensure safety, optimum performance
and familiarize yourself fully with the use of the motorized microscope, we recommend that you
study this manual thoroughly before operating the system. Retain this instruction manual in an
easily accessible place near the work desk for future reference.
A X 9 9 4 4
Downloaded from
ManualsNet.com
search engine
Advertisement
Table of Contents
Related Manuals for Olympus BX-UCB
Summary of Contents for Olympus BX-UCB
- Page 1 HAND SWITCH Optical Microscope Accessory This instruction manual is for the Olympus Control Box model BX-UCB and Hand Switch model U- HSTR2, both for use with the BX2 motorized microscope. To ensure safety, optimum performance and familiarize yourself fully with the use of the motorized microscope, we recommend that you study this manual thoroughly before operating the system.
- Page 2 Refer to your local Olympus distributor in EU for return and/or collection systems available in your country. NOTE: This product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
-
Page 3: Table Of Contents
CONTENTS IMPORTANT — Be sure to read this section for safe use of the equipment. — NOMENCLATURE OPERATION Control Box BX-UCB ..................................5 Turning Power On Functions of Indicator LEDs Hand Switch U-HSTR2 ................................5 Attaching Indication Stickers Grouping Panel Sheet Operation Settings of the DIP Switches ...................... -
Page 4: Important - Be Sure To Read This Section For Safe Use Of The Equipment
(For the operating environmental condition, see chapter 3, “SPECIFICATIONS” on page 7.) 3. While the main switch of the BX-UCB control box is set to “ I ” (ON), do not replace any module, plug or unplug any cable or switch the light path manually to prevent malfunction (manual switching of the revolving nosepiece is permitted). - Page 5 BX-UCB/U-HSTR2 Caution If the equipment is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the equipment may also be damaged. Always use the equipment as outlined in this instruction manual.
-
Page 6: Nomenclature
NOMENCLATURE Make sure to connect the Olympus-specified module to each connector. The PC in use should meet the IEC60950 requirements. If any non-specified equipment is used, Olympus cannot guarantee any performance of the system. Control Box BX-UCB Indicator LEDs · RMT: Lights at the time of remote control (in orange). - Page 7 BX-UCB/U-HSTR2 Hand Switch U-HSTR2 }The functions of the buttons on this hand switch are variable depending on whether the attached vertical illuminator is the BX- RFAA (on the upper stage) or the BX-RLAA (on the lower stage). The button functions can be set arbitrarily when the PC control (remote control) is used.
-
Page 8: Operation
OPERATION 2-1 Control Box BX-UCB Turning Power On (Fig. 1) Ensure that the modules to be used are connected properly. ² 1. Set the main switch @ to “ I ” (ON). 2. Ensure that the LED indicators ² corresponding to the connected mod- ules are lit. -
Page 9: Operation Settings Of The Dip Switches
BX-UCB/U-HSTR2 2-3 Operation Selection of the DIP Switches }The allocated functions of the DIP switches are shown in the table below. # Make sure the main switch is set to “ ” (OFF) before setting the DIP switches. The unit detects the new settings only when the power is switched on, making those settings effective. -
Page 10: Specifications
125(W) x 216(H) x 310(D) mm, approx. 5 kg (11 lb.) Hand Switch U-HSTR2 Button functions Connects to the BX-UCB for use in the control of following operations. (Can also be connected to Olympus AX70, AX80 or U-REMPS but the operation is not normal in this case.) When a PC is not used: ·... -
Page 11: Troubleshooting Guide
Under certain conditions, performance of the microscope may be adversely affected by factors other than defects. If a problem occurs, please review the following list and take remedial action as appropriate. If you cannot solve the problem after checking the entire list, please contact your local Olympus representative for assistance. Problem... -
Page 12: Assembly
U-LH100-3 Rear panel Extension cord U-RMT Power cord Control Box BX-UCB Hand Switch U-HSTR2 Be sure to set the main switch to “ ” (OFF) before connecting cables. # The U-UCD8A and BX-RLAA cannot be used simultaneously. If both modules are used together, malfunction will result. - Page 13 Connecting the Power Cord (Figs. 5 to 7) ³ Always use the power cord provided by Olympus. If no power cord is provided, please select the proper power cord by referring to the section “PROPER SELECTION OF THE POWER SUPPLY CORD” at the end of this instruction manual.
-
Page 14: Proper Selection Of The Power Supply Cord
If no power supply cord is provided, please select the proper power supply cord for the equipment by referring to “ Specifications ” and “ Certified Cord ” below: CAUTION: In case you use a non-approved power supply cord for Olympus products, Olympus can no longer warrant the electrical safety of the equipment. - Page 15 BX-UCB/U-HSTR2 Table 2 HAR Flexible Cord APPROVAL ORGANIZATIONS AND CORDAGE HARMONIZATION MARKING METHODS Alternative Marking Utilizing Printed or Embossed Harmoniza- Black-Red-Yellow Thread (Length tion Marking (May be located on Approval Organization of color section in mm) jacket or insulation of internal wir-...
- Page 16 Manufactured by Shinjuku Monolith, 2-3-1 Nishi-Shinjuku, Shinjuku-ku, Tokyo 163-0914, Japan Distributed by 48 Woerd Avenue Waltham, MA 02453, U.S.A. 8F Olympus Tower, 446 Bongeunsa-ro, Gangnam-gu, Seoul, 06153 Korea Printed in Japan 20160122 M0000 AX9944 09 Downloaded from ManualsNet.com search engine...