1. Manuals
  2. Brands
  3. Let's Go Aero Manuals
  4. Bicycle Accessories
  5. B02301
  6. Manual

Let's Go Aero B02301 Manual

V-lectric fat pro expansion kit
Hide thumbs
1
2
3
4

Advertisement

Table of Contents

Accessory 2-Bike Expansion Kit for V-Lectric Bicycle Carrier (P/N B01892, B02158 or B00390
PARTS
QTY. DESCRIPTION
N
1
BASE
P
4
HAT BRACKETS
Q
8
5/16" X 1" CARRIAGE BOLTS
U
8
5/16" WASHERS
V
8
5/16" NYLOCK NUTS
W
4
UPPER WHEEL CRADLE
X
4
LOWER WHEEL CRADLE
Y
8
RUBBER STRAP
Z
2
WING
AA
8
CRADLE HOUSING
BB
2
WIRE LOCK PIN
NOTE: This manual assumes you
have already assembled your pre-
owned V-Lectric Bicycle Carrier.
NOTICE: All Manual information is subject to change without notice. Revised editions
will be available for free download at LetsGoAero.com. Manual information is considered
factual until made obsolete by a revised version.
Follow this QR-Code or visit
LetsGoAero.com/manuals to check for an updated version:

: Preparation

STEP 1
Loosen the Hat Brackets [P] of the Base [N] already installed on
your pre-owned V-Lectric Carrier.
Slide the Base [N] back towards the vehicle and out of the way.
Leave these connections loose at this time.
NOTE: This V-Lectric Expansion Kit add-on MUST position furthest
away from vehicle. The Safety Cable located on the Base included
with your original V-Lectric Carrier [N] MUST be positioned closest
to the vehicle.
Copyright© 2022, Lets Go Aero, Inc., All rights reserved.
B02301-020922rev
sold separately). Rated for 150 lbs (75 lbs per bicycle).
V-Lectric FAT PRO Expansion Kit
2-Bike Accessory Add-on (for V-Lectric Bicycle Carrier)
[Fg.1]
Page 1 of 4
Part No. B02301
N
P
Revision Date: 02/09/22

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the B02301 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Let's Go Aero B02301

Summary of Contents for Let's Go Aero B02301

  • Page 1 V-Lectric FAT PRO Expansion Kit 2-Bike Accessory Add-on (for V-Lectric Bicycle Carrier) Part No. B02301 Accessory 2-Bike Expansion Kit for V-Lectric Bicycle Carrier (P/N B01892, B02158 or B00390 sold separately). Rated for 150 lbs (75 lbs per bicycle). PARTS QTY. DESCRIPTION...
  • Page 2 STEP 2 REQUIRED TOOL: 1/2” WRENCH Set the new Base [N] on top of the platform. [Fg. 2] Bring each Hat Bracket [P] (four total) up from underneath platform so the Hat Brackets wrap around the tubes of the platform and align with the holes on the Base [N]. Using two (2) 5/16in Carriage Bolts [Q], two (2) 5/16in Carriage Washers [U], and two (2) 5/16in Nylock Nuts [V] per Hat Bracket [P] LOOSELY connect each Hat Bracket to the Base [N] as...
  • Page 3 STEP 4: Slide the round end of one (1) Rubber Strap [Y] onto [Fg. 5] each Upper Wheel Cradle [W] and Lower Cradle [X]. [Fg. 5] NOTE: Be sure to slide the Rubber Straps [Y] all the way onto the cradles so that it tightly rests over the plastic coating of the Wheel Cradle [W &...
  • Page 4 Operation: Bicycle Mounting Refer to your original V-Lectric Manual P/N B01892, B02158, or B00390 for proper bicycle mounting procedure. WARNING: Always secure each bicycle with all four connections points (two Upper Wheel Cradles & two Lower Cradles). Do not operate the vehicle unless all connection points are tight and secured. Failure to follow bicycle mounting procedure may result in damage to carrier, damage to property, bodily injury or death.

Table of Contents