Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Faraday MPC-NET2
- Page 1 MPC-NET2 MPC-Net System Networking Owner’s Manual 315-049594 Revision 1.0 03/2005 Siemens Building Technologies, Inc. 8 Fernwood Road • Florham Park, NJ 07932 Tel: (973) 593-2600 • Fax: (973) 593-6670 Web: www.faradayfirealarms.com P/N 315-049594-1 firealarmresources.com...
- Page 2 This page is intentionally blank. P/N 315-049594-1 firealarmresources.com...
-
Page 3: Table Of Contents
Table of Contents FARADAY MPC-NET ..........................5 INTRODUCTION ............................5 INSTALLATION ............................5 Network Wiring............................5 Fiber Converters ............................ 5 NIB Versions ............................5 Before Connecting NIBs ........................6 Node Numbering............................ 6 Panel-NIB Configuration ........................6 Printer-NIB Configuration........................6 Computer-NIB Configuration ......................... 6 Network Links ............................ - Page 4 P/N 315-049594-1 firealarmresources.com...
-
Page 5: Faraday Mpc-Net
I. FARADAY MPC-NET2 INTRODUCTION The Faraday MPC-NET2 network is a way to link MPC-6000 or MPC-7000 Fire Alarm Control units, RND-2 Remote Network Displays and printers together to form a network. MPC-6000 and MPC-7000 Firmware version 3.0 or higher is required to be running on each panel. A total of 99 Network Interface Boards (NIBs) can be connected on a network. -
Page 6: Before Connecting Nibs
Before Connecting NIBs Each panel should be running and free of troubles and alarms before attempting to connect to the network. When panels are free of troubles and alarms proceed to the Panel-NIB configuration section. Node Numbering A total of 99 NIBs can be connected on a network. Addresses 1 thru 99 are to be used for MPC-6000, MPC-7000, RND-2 Remote Network Displays, printers, and computers used as simple terminals to log network events. -
Page 7: Trouble Indications
Trouble Indications All panels and network annunciators connected to the network will indicate network specific faults (see Section III for details). Individual panel system troubles (ground fault, battery, etc) will not be transmitted to other fire panels but will be transmitted to the RND-2s, network printers and simple monitoring computers. All initiating devices on the MPC-6000 or MPC-7000 can also be programmed to a network LINK (accomplished while configuring devices on the panel). -
Page 8: Supervisory Indications
Supervisory Indications Individual fire panel supervisory conditions will be transmitted to the RND-2s and network printers. All initiating devices on the MPC-6000 or MPC-7000 can also be programmed to a network LINK (accomplished while configuring devices on the panel). The maximum LINK number for the MPC-6000 and MPC-7000 is 255. If an initiating device on a panel goes into supervisory, and it has been programmed to a network LINK, it will send a network message to the other panels indicating that the network LINK is in supervisory. -
Page 9: Ii. Network Annunciators
II. NETWORK ANNUNCIATORS It is HIGHLY RECOMMENDED that at least one RND-2 annunciator is included on the network. RND-2 The RND-2 is designed to annunciate network events (alarms, troubles and supervisories). It is capable of scrolling through network events. These events can be acknowledged either globally or for the RND-2 only. Alarms may also be silenced globally. - Page 10 P/N 315-049594-1 firealarmresources.com...
-
Page 11: Network Troubleshooting
III. NETWORK TROUBLESHOOTING NIB LED INDICATORS LEDs on the 12523, 12526 and 12603 NIBs LEDs on the 12523A, 12526A and 12603A NIBs D7 D6 D5 D4 D3 LEDs on bottom side of PCB Name Description Reverse link (port 1, arc1) This LED is on steady when a link to the next NIB is established to Port 1 of the next NIB. -
Page 12: Network Specific Troubles
NETWORK SPECIFIC TROUBLES ENTRY INDICATES NW Node Count The programmed configuration for the number of network nodes doesn’t match the actual number of nodes found on the network. NN’nnn’ Com Flt The panel at node ‘nnn’ is not communicating with its NIB. NET NODE ‘nnn’... -
Page 13: Iv. Wiring Diagrams
7000 Fire Alarm System Control Unit or the RND-2 Remote Network Display. The NIB mounts to a 6- gang box, 2” deep minimum. The Faraday 12411 surface backbox or the 12525 surface backbox with transient suppressor may be used for surface mounting. - Page 14 P/N 315-049594-1 firealarmresources.com...
- Page 15 P/N 315-049594-1 firealarmresources.com...
-
Page 16: 12525 Line Surge Suppressor
12525 LINE SURGE SUPPRESSOR The 12525 is a data line Surge Suppressor and is required when networking from building to building using Category 5 wiring. The 12525 Surge Suppressor comes mounted in a surface backbox and can be used with a 12523A or 12526A Network Interface Board for mounting. Step 1.) Installation is to be done by qualified personnel who have thoroughly read and Notes:... -
Page 17: 12526 Or 12526A Network Interface Board With Isolated Rs232 Port
The 12526 or 12526A Network Interface Board with an isolated RS232 port is for hooking up a printer or computer to the network. The NIB mounts to a 6-gang box, 2” deep minimum. The Faraday 12411 Surface Backbox or the 12525 Surface Backbox with Transient Suppressor may be used for surface mounting. - Page 18 P/N 315-049594-1 firealarmresources.com...
-
Page 19: 12603 Or 12603A Network Interface Board
12603A NETWORK INTERFACE BOARD The 12603 or 12603A Network Interface Board is a module to interface between the MPC-6000 or MPC-7000 Fire Alarm System Control Unit and the FARADAY MPC-NET2 Network. The NIB mounts inside the MPC-6000 cabinet. Notes: 1.) Units to be installed in accordance with all local codes. -
Page 20: 12535 And 12536 Fiber Converter Board
12535 and 12536 FIBER CONVERTER BOARD The 12535 Multimode Fiber Converter and 12536 Single Mode Fiber Converter Boards are for allowing the 12523A, 12526A and 12603A Network Interface Boards to use fiber connections. For 12535 Multimode Fiber Converter: Install on NIB, carefully aligning pins on Converter with headers on NIB. Connect wiring to Fire Alarm Panels, computers, or printers as described earlier in the wiring diagram section. -
Page 21: Appendix A Network Links Model
Appendix A Network Links Model link 1 link 2 link 3 Network Links (up to 255) link 4 link 5 link 6 link 7 link 255 Any input on Network links are Events on group group 1 on any of The output of an equivalent to a 2 will cause... - Page 22 P/N 315-049594-1 firealarmresources.com...
- Page 23 P/N 315-049594-1 firealarmresources.com...
- Page 24 P/N 315-049594-1 firealarmresources.com...