Advertisement
Quick Links
DESCRIPTION
The AT 252 anchor beam is a portable anchor point. Beam can be used on the concrete wells of diameter from 800mm to
2000mm. Device can be used for lifting loads. Winch is equipped with automatic brake for load suspension.
Device consist of:
a) Foldable beam with cast iron wheel for working rope guidance.
b) Pillar "A" with plate for winch installation.
c) Pillar "B".
Brake winch RUP502-T (for lifting loads) sold separately.
Device is made of powder painted steel. Each Pillar is equipped with locking pin with spring for quick beam installation.
Foldable beam for easier transport consist of centrally installed wheel for working rope guidance and two arms with 9 pcs. of
locking holes for proper adjustment to the well. The beam in the working position is protected against accidental closing with
locking pins with spring. Attachment point under the wheel can be used for attaching additional equipment.
Pillar "B"
PARAMETERS
•
Working Load Limit (WLL): 500kg
•
Ability to install RUP502-T brake winch
•
Powder painted steel construction
•
Weight: ~24kg (without winch)
•
Shipping dimensions: 115x55x65cm
edition: 2/20.02.2015 en
ANCHOR BEAM FOR CONCRETE WELLS
EQUIPMENT FOR LIFTING LOADS
Reference
number:
Foldable
Wheel for
Beam
rope guidance
800... 2000mm
Beam arm with 9 pcs.
adjustment holes
Locking pin with spring
AT 252
Pillar "A"
Concrete well
Locking pin with spring
INSTRUCTION MANUAL
READ CAREFULLY BEFORE
USE THE EQUIPMENT
RUP502-T brake winch (for lifting loads)
sold separately
Additional attachment
point under the wheel
Foldable beam
Locking pin
for rope secure
1/7
Advertisement
Related Manuals for Protekt AT 252
Summary of Contents for Protekt AT 252
- Page 1 DESCRIPTION The AT 252 anchor beam is a portable anchor point. Beam can be used on the concrete wells of diameter from 800mm to 2000mm. Device can be used for lifting loads. Winch is equipped with automatic brake for load suspension.
- Page 2 RUP502-T BRAKE WINCH INSTALLATION Remove grip from RUP502-T brake winch according to RUP5-2-T Instruction manual - "Removing the grip fo the RUP502-T device". Install winch without grip to the plate on Pillar "A" using the same bolts and nuts. RUP502-T brake winch without grip Pillar "A"...
- Page 3 PREPARATION OF THE BEAM Open both arms of the foldable beam - step "a". Pull back the locking finger - step "b", and fully open the arm - step "c". Locking finger should move back automatically. Repeat sequence for second arm. To unlock the arm pull back the locking finger and close the arm.
- Page 4 ANCHOR BEAM INSTALLATION ON THE CONCRETE WELL Adjust pillars spacing so that the pulley was near the center of the concrete well - step "g". Pillar limiters should be located as close as possible to the outer well surface - step "h". "g"...
- Page 5 500 kg CAUTION! • The lifting / lowering function is for lifting / lowering loads only. Do not use AT 252 anchor beam witch winch for a rescue or a fall arrest purposes. • Always operate the winch with hand power and with crank included in the equipment only.
- Page 6 CONTENT OF THE IDENTITY LABEL a) Device type. b) Model symbol. c) Reference number. d) Equipment only for lifting loads - notice. e) Month and year of manufacture. f) Serial number of the tripod. g) Caution: read the manual. h) Marking of the manufacturer or distributor of the tripod. TRANSPORT Device should be transported in packaging protecting it from damage or getting wet, e.g.
- Page 7 NAME AND DATE OF REASON FOR SERVICING / DATE REPAIRS CARRIED OUT SIGNATURE OF NEXT REPAIR COMPETENT PERSON EXAMINATION PRODUCER: PROTEKT, 93-403 LODZ, ul. Starorudzka 9, POLAND, tel: +48 (42) 680 20 83, fax: +48 (42) 680 20 93, www.protekt.com.pl...
Need help?
Do you have a question about the AT 252 and is the answer not in the manual?
Questions and answers