Related Manuals for Wavecom WCM-TT040-50BB
Summary of Contents for Wavecom WCM-TT040-50BB
- Page 1 Wavecom WCM-TT040-50BB Bluetooth Ready Battery Powered Printer User Manual + Certificate of Warranty and Product Support Information...
-
Page 2: Table Of Contents
Gap/Black Mark Sensor Calibration Gap/Black Mark Calibration, Self-test and Dump Mode Dump mode Printer Initialization Set Black Mark Sensor as Media Sensor and Calibrate the Black Mark Sensor Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor Troubleshooting Maintenance Wavecom Tags... -
Page 3: Printer Diagram
User Manual Wavecom Wavecom Thermal Transfer Printer The TT040-50-BB printer is powered by a Lithium Ion Battery and features Bluetooth connectivity. Important: Do not turn off the rear power switch on the TT040-50-BB. Always use the Power Button on the side of the printer (7). -
Page 4: Charging The Printer
WCM-TT-040-40BB User Manual Wavecom Charging the Printer Using this method to charge the printer will avoid any issues with inrush current when the charging cable is plugged in, which can occur if the battery is not isolated. Ensure the isolation switch is turned on once the charging cable is plugged in, otherwise the battery will not charge. -
Page 5: Operating The Printer
WCM-TT-040-40BB User Manual Wavecom Operating the Printer Turning on the Printer Before turning on the printer, ensure the battery is charged, and the battery isolation switch on the side of the printer is switched ON. 2. Press and hold the power button on the side of the printer for three to five seconds. The Battery Status indicator (next to the power button) will light up when the printer has turned on. -
Page 6: Loading Print Media
WCM-TT-040-40BB User Manual Wavecom Loading the media Loading media into the TT-040-50 Printer is quick and easy. To begin, open the printer top cover by pulling the tabs located on each side towards the front of the printer, and then lift the top cover to the maximum open angle. -
Page 7: Loading Print Ribbon
WCM-TT-040-40BB User Manual Wavecom Loading the Ribbon To begin, open the printer top cover by pulling the tabs located on each side towards the front of the printer, and then lift the top cover to the maximum open angle. You will also need to remove the old ribbon (which will be spooled under the top cover shown in step 1) before loading a new ribbon. -
Page 8: Printer Functions
WCM-TT-040-40BB User Manual Wavecom Printer Functions LED and Button Functions This printer has one button and one three-colour LED indicator. By indicating the LED with different colour and pressing the button, printer can feed labels, pause the printing job, select and calibrate the media sensor, print printer self-test report, reset printer to defaults (initialization). -
Page 9: Gap/Black Mark Sensor Calibration
WCM-TT-040-40BB User Manual Wavecom Gap/Black Mark Sensor Calibration Gap/black mark sensor sensitivity should be calibrated in the following circumstances: 1. A brand new printer 2. Change label stock 3. Printer initialization Please follow the steps below to calibrate the gap/black mark sensor. -
Page 10: Dump Mode
WCM-TT-040-40BB User Manual Wavecom Dump mode Printer will enter dump mode after printing printer configuration. In the dump mode, all characters will be printed in 2 columns as following. The left side characters are received from your system and right side data are the corresponding hexadecimal value of the characters. -
Page 11: Set Black Mark Sensor As Media Sensor And Calibrate The Black Mark Sensor
WCM-TT-040-40BB User Manual Wavecom Set Black Mark Sensor as Media Sensor and Calibrate the Black Mark Sensor 1. Turn off the power switch. 2. Hold on the button then turn on the power switch. 3. Release the button when LED turns green/amber after 5 green flashes. (Any green/amber will do during the 5 flashes). -
Page 12: Troubleshooting
WCM-TT-040-40BB User Manual Wavecom Troubleshooting The following guide lists the most common problems that may be encountered when operating this bar code printer. If the printer still does not function after all suggested solutions have been invoked, please contact the Customer Service Department of your purchased reseller or distributor for assistance. - Page 13 WCM-TT-040-40BB User Manual Wavecom Print Problems Problem Possible Cause Recovery Procedure Check if interface cable is well Re-connect cable to interface. connected to the interface connector. The serial port cable pin configuration Please replace the cable with pin to pin connected.
-
Page 14: Maintenance
WCM-TT-040-40BB User Manual Wavecom Maintenance This session presents the clean tools and methods to maintain your printer. Please use one of following material to clean the printer. • Cotton swab (Head cleaner pen) • Lint-free cloth • Vacuum / Blower brush •... -
Page 15: Wavecom Tags
All of the Wavecom tags are suitable for printing using every brand of thermal transfer printers available from around the world. The adhesive used on our tags is most aggressive and comes highly recommended for use in the electrical test and tag industry, there should be no butterflying once applied. - Page 16 WCM-TT-040-40BB User Manual Wavecom Purchase Information Date of Purchase Sold By Wavecom Wavecom SA Wavecom WA Wavecom VIC 257 Grange Road, Unit 2/17 Casino Street, Mark Kennedy Findon SA, 5023 Welshpool WA, 6106 M: 0430 299 164 P: 08 8243 3500...