3.1. Power and control module ............................5 CONFIGURATION ................................... 8 CONNECTION OF PERIPHERALS TO THE CAN BUS ........................9 5.1. Connection between the COMPACT and the COMPACT-E units ................. 10 5.2. Connection between COMPACT-E unit and CAN-AV speed adapter ................11 INSERTING THE CARDS................................. 12 COMMISSIONING THE UNIT ..............................
Emergency Mode. 3. REAR VIEW Figure 2 (1) Slots 1 to 10 – Blank plates. Allow expanding the system with cards UMX-C16, UMX-2SA, UMX-2SB or UMX-MC6. (2) Power and control module. See section 3.1. COMPACT-E version 5.0.001 R+D Department...
COMPACT-E and CAN peripherals (ME-200C, MD-30C, NS-CAN). To connect them it is recommended to use a shielded twisted pair AWG24 cable. Follow figure 4 if the COMPACT-E unit is an intermediate element of the CAN bus or follow figure 5 if it is an end element.
Page 8
The detection time of the activation pulse of the input contacts is configurable through the Call Point software (0-50-100-200- 300-400-500-1000-1500-2000 milliseconds). To connect follow figure 8. If you wish to monitor the contact, follow figure 9. Figure 8 Figure 9 INPUT CONTACT CONNECTION WITHOUT SURVEILLANCE INPUT CONTACT CONNECTION WITH SURVEILLANCE COMPACT-E version 5.0.001 R+D Department...
Page 9
CAN Bus position Configure external DIP switches 5 and 6 to indicate the position on the CAN bus occupied by the COMPACT-E (end BUS END ELEMENT BUS INTERMEDIATE element or intermediate element). See figure 10.
5. CONNECTION OF PERIPHERALS TO THE CAN BUS The COMPACT device communicates with the COMPACT-E units via a CAN bus. The data flow between the COMPACT equipment and the COMPACT-E expansion units uses a baud rate of 500 kbit/s.
5.1. Connection between the COMPACT and the COMPACT-E units Use the AUDIO LINK BUS and the CAN BUS contacts to connect the COMPACT matrix to the COMPACT-E units. For the connection of the CAN bus it is recommended to use a shielded twisted pair AWG24 cable.
COMPACT system COMPACT-E expansion unit 5.2. Connection between COMPACT-E unit and CAN-AV speed adapter The communication speed of the CAN bus of the COMPACT-E device is 500 kbit/s. If a Figure 18 COMPACT-E unit matches other CAN periph- erals (MD-30C, ME-200C, NS-CAN…) on the...
Commissioning the unit requires sending of configurations to the COMPACT audio matrix whose CAN bus depends on the COMPACT-E unit. To do this, you need a PC equipped with a network card and connected to the COMPACT matrix, either through a switch, or directly through a network cable.
Allows using cards UMX-C16, UMX-2SA, UMX-2SB and UMX-MC6 Power supply 24V DC. Dual power supply (primary and secondary) Consumption 250 mA (without cards). Weight 8 kg Finishes RAL9005 iron painted black Measurements 482.6 (width) x 133 (height) x 280 (depth) Rack units COMPACT-E version 5.0.001 R+D Department...
3.2.000 June 2018 11. Software and firmware versions. R+D Department 3.1. Power and control module. 5.1. Connection between the COMPACT and the COMPACT-E UNITS. 3.2.001 October 2018 R+D Department 5.2. Connection between COMPACT-E unit and CAN-AV speed adapter. 10. Software and firmware versions.
Tel. 902 151 96 / 972 203 300 The guarantee shall not be valid whenever the following is observed: Fax. 972 21 84 13 Amendments or corrections made to the details of the guarantee certificate e-mail:girona@optimus.es 1999/44/CE or purchase invoice. COMPACT-E version 5.0.001 R+D Department...
Page 21
CONFIGURACIÓN ................................... 8 CONEXIÓN DE PERIFÉRICOS AL BUS CAN..........................9 5.1. Conexión entre COMPACT y COMPACT-E........................10 5.2. Conexión entre COMPACT-E y el adaptador de velocidad CAN-AV ................11 INSERCIÓN DE LAS TARJETAS ............................... 12 PUESTA EN MARCHA DEL EQUIPO ............................12 ALARMAS DEL SISTEMA ...............................
Unidad de ampliación del sistema COMPACT. Ofrece 10 slots de capacidad para alojar tarjetas UMX-C16, UMX-2SA, UMX-2SB o UMX-MC6, comunicándose con la unidad principal COMPACT a través de un bus CAN. Cada matriz de audio COMPACT puede ampliarse con un máximo de 10 unidades COMPACT-E. Dispone de doble alimentación, primaria y secundaria, para instalaciones con redundancia.
Para su conexión se recomienda la utilización de un cable de par trenzado y apantallado AWG24. Siga la figura 4 si el equipo COMPACT-E es un elemento intermedio del bus CAN, o siga la figura 5 si es elemento final del bus.
Page 24
El tiempo de detección del pulso de activación de los contactos de entrada es configurable a través del software Call Point (0- 50-100-200-300-400-500-1000-1500-2000 milisegundos). Para su conexión siga la figura 8. Si desea supervisar el contacto, siga la figura 9. Figura 8 Figura 9 CONTACTO DE ENTRADA SIN SUPERVISION CONTACTO DE ENTRADA CON SUPERVISIÓN COMPACT-E versión 5.0.001 R+D Department...
Page 25
Cada matriz de audio COMPACT puede ampliarse con un máximo de 10 unidades COMPACT-E, por lo que en tal ca- so se utilizarán 10 direcciones CAN distintas. La figura 11 muestra la combinación de los DIP switches b0, b1, b2 y b3 para asignar las direcciones CAN 1 a 10.
COM REFERENCIADO A GND GENERAL SW3: UNIÓN ENTRE EL NEGATIVO DE ALIMENTACIÓN Y CHASIS DIP SWITCH 1 ON* * UNIDOS DIP SWICTH 2 ON* DIP SWITCH 1 OFF SEPARADOS DIP SWICTH 2 OFF COMPACT-E versión 5.0.001 R+D Department...
5. CONEXIÓN DE PERIFÉRICOS AL BUS CAN El equipo COMPACT se comunica con las unidades COMPACT-E a través de un bus CAN. El flujo de datos entre el equipo COMPACT y las unidades de ampliación COMPACT-E utiliza una velocidad de transmisión de 500 kbit/s.
5.1. Conexión entre COMPACT y COMPACT-E Utilice los conectores BUS AUDIO LINK y los contactos BUS CAN para unir la matriz COMPACT con las unidades COMPACT-E. Para la conexión del bus CAN se recomienda la utilización de un cable de par trenzado y apantallado AWG24.
Unidad de ampliación COMPACT-E del sistema COMPACT 5.2. Conexión entre COMPACT-E y el adaptador de velocidad CAN-AV La velocidad de comunicación del bus CAN del equipo COMPACT-E es de 500 kbit/s. En insta- Figura 18 laciones donde coincidan en un mismo bus CAN equipos COMPACT-E con otros periféri-...
La puesta en marcha del equipo requiere el envío de configuraciones a la matriz de audio COMPACT de cuyo bus CAN depende la unidad COMPACT-E. Para ello, es necesario un PC equipado con tarjeta de red y conectado a la matriz COMPACT, bien a través de un switch, o directamente a través de un cable de red.
5.1. Conexión entre COMPACT y COMPACT-E. 3.2.001 Octubre 2018 R+D Department 5.2. Conexión entre COMPACT-E y el adaptador de velocidad CAN-AV. 10. Versiones de software y firmware. Apartado 3.1. El tiempo de detección del pulso de activación de los contac- tos de entrada puede configurarse.
Enmiendas o tachaduras en los datos del certificado de garantía o factura Tel. 902 151 96 / 972 203 300 de compra. Fax. 972 21 84 13 e-mail:girona@optimus.es 1999/44/CE Falta de factura original o falta de fecha en la misma. COMPACT-E versión 5.0.001 R+D Department...