Chamberlain GJ Owner's Manual
  1. Manuals
  2. Brands
  3. Chamberlain Manuals
  4. Gate Opener
  5. GJ
  6. Owner's manual
Chamberlain GJ Owner's Manual

Chamberlain GJ Owner's Manual

Hide thumbs Also See for GJ:
Table of Contents

Advertisement

Quick Links

Download this manual
Serial #
(located on electrical box cover)
Installation Date
Wiring Type
OWNER'S MANUAL
MODEL GJ
SOLID STATE
INDUSTRIAL DUTY
GEARHEAD JACKSHAFT OPERATOR
©
The Chamberlain Group, Inc.
A DUCHOSSOIS ENTERPRISE
845 Larch Avenue
Elmhurst, Illinois 60126
NOT FOR RESIDENTIAL USE
LR78500
41B6
R
R
CERTIFIED
LISTED
DOOR
DOOR
OPERATOR
OPERATOR

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GJ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Chamberlain GJ

Summary of Contents for Chamberlain GJ

  • Page 1 The Chamberlain Group, Inc. A DUCHOSSOIS ENTERPRISE 845 Larch Avenue © Elmhurst, Illinois 60126 OWNER'S MANUAL MODEL GJ SOLID STATE INDUSTRIAL DUTY GEARHEAD JACKSHAFT OPERATOR NOT FOR RESIDENTIAL USE LR78500 41B6 Serial # (located on electrical box cover) Installation Date...

  • Page 2: Specifications

    SIGHT OF DOOR OR ANY OTHER CONTROL left or right side (AUTOMATIC OR MANUAL) IS USED. WEIGHTS AND DIMENSIONS HANGING WEIGHT: ..80-110 LBS. 14" 7" 5-1/2" 8-7/8" 4-3/4" GJ OPERATOR 1/2 HP 3/4 HP 1 HP 1 1/2 HP 2 HP CLUTCH 28-11/16” 24-15/16” 28-13/16”...

  • Page 3: Important Safety Notes

    MOUNTING CONVERSIONS The GJ operator may be mounted on either the right (standard) or left side of door, and in either a vertical (standard) or horizontal mounting position. Refer to the steps below if you require the hand chain and/or disconnect chain to be on the opposite side of the operator;...

  • Page 4: Operator Mounting

    OPERATOR MOUNTING The standard GJ operator is setup for mounting on right side of the door and in vertical position. If necessary, refer to the operator mounting conversions on page 3. Refer to the illustrations and instructions below that suits your application.
  • Page 5 7. Install Hand Chain Place hand chain around hand chain wheel. Be sure to pass it through both openings in the chain Mount Chain Keeper guide. Remove enough links so chain hangs approx. 4 feet above approximately two feet above the floor. floor 8.
  • Page 6 INSTALL CONTROL STATION Before installing control station be sure to follow all warnings described below. Failure to so may result in severe injury to persons and/or damage to operator. Do not install any wiring or attempt to run the operator without consulting the wiring diagram. Install the optional Reversing Edge before proceeding with the Control Station installation.
  • Page 7 3. Repeat Steps 1 and 2 for close cycle. Be sure close limit actuator is engaged as door fully seats at the floor. The Chamberlain Group, Inc. If other problems persist, call our toll-free number for assistance - 1-800-528-6563.

  • Page 8: Caution Warning

    ADJUST CLUTCH (OPTIONAL) RNING WARNING Motor TO AVOID SERIOUS PERSONAL INJURY OR DEATH FROM ELECTROCUTION, DISCONNECT ELECTRIC Clutch POWER TO OPERATOR BEFORE ADJUSTING SLIP CLUTCH. Adjusting Remove clutch cover and adjust clutch so that it is tight enough to open and close the door but will slip UTION WARNING when the door meets an obstruction.

  • Page 9: How To Order Parts

    INSTALLATION AND SERVICE INFORMATION ARE AVAILABLE 6 DAYS A WEEK ADDRESS ORDER TO: CALL OUR TOLL FREE NUMBER – 1-800-528-6563 THE CHAMBERLAIN GROUP, INC. HOURS 7:00 TO 3:30 p.m. (Mountain Std. Time) Electronic Parts & Service Dept. MONDAY Through SATURDAY 2301 N.
  • Page 10 awaiting page 10...
  • Page 11 Hot 115V, 208-230V, 1Ø TB1- Remove Jumper Open to Install Interlock Close Open / Close Stop Sensing Device RADIO CONTROL (24V dc only) The Chamberlain Group, Inc. 1Ø Standard Power & Control Connection Diagram Solid State CDO 2/22/94 - 2/25/94...
  • Page 12 SOLID STATE THREE PHASE WIRING DIAGRAM SENSING LIMIT Yellow SWITCH White THIS WIRE NOT USED ON 3/4 HP AND ABOVE WITH POWER INDUCTOR White CLOSE OPEN LIMIT Blue LIMIT Blue SWITCH SWITCH White Yellow White White Orange MOTOR Blue Black White Yellow 1/3 &...
  • Page 13 2/27/94 - 3/9/94 STANDARD POWER AND CONTROL CONNECTION DIAGRAM (Solid State Board CDO - 208-230V, 3Ø) L1 N 208-230V, 3Ø 208-230V, 3Ø L2 H 208-230V, 3Ø TB1- Open Close Open / Close Stop RADIO CONTROL (24V dc only) Sensing Device OPTIONAL SETTINGS Set Maximum Run Timer Begin with door in closed position.

  • Page 14: Operating Mode

    3 Button, 1 Button, 1 & 3 Button Radio Control Function: Momentary contact to open, close and stop, plus wiring for The Chamberlain Group, Inc. sensing device to reverse and auxiliary devices to open and close New Wiring Kit Art with open override.
  • Page 15 NEMA MOTOR WIRING DIAGRAMS NEMA MOTOR WIRING DIAGRAMS SINGLE VOLTAGE The Chamberlain Group, Inc. 1/3 & 1/2HP 115V only NEMA Motor Wiring Diagrams 2/19/94 115V Motor Black T1 - Blue Blue T4 - Yellow Yellow 1KΩ 5W T5 - Black...
  • Page 16 ILLUSTRATED PARTS – ELECTRICAL BOX SOLID STATE...
  • Page 17 REPAIR PARTS LIST – ELECTRICAL BOX SOLID STATE Below is a parts list for a standard model GJ electrical box. Optional modifications and/or accessories may add or remove certain parts from this list. Refer to page 9 for all repair part ordering information.
  • Page 18 ILLUSTRATED PARTS – MODEL SOLID STATE...
  • Page 19 REPAIR PARTS LIST – MODEL SOLID STATE Below is a parts list for a standard model GJ operator. Optional modifications and/or accessories may add or remove certian parts from this list. Refer to page 9 for all repair part ordering information.

  • Page 20: Control Connection Diagram

    B2, T & TS MODE ONLY RADIO CONTROL (24Vdc only) SENSING DEVICE TO REVERSE OR STOP EXTERNAL INTERLOCK REMOVE JUMPER 2 OR MORE WIRING TYPES - ALL © 1996, The Chamberlain Group, Inc. 114A1999 All Rights Reserved Printed in Mexico...

Table of Contents