Advertisement
Quick Links
Operation Manual
Sliding Door System Set
61811
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Summary of Contents for WilTec 61811
- Page 1 Operation Manual Sliding Door System Set 61811 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
- Page 2 All rights re- served. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Always use the door handle to close the door. Note! Use of excessive force to open and close the door(s) can damage the item. Always hold the handle and open and close the door(s) gently. © by WilTec Wildanger Technik GmbH Item 61811 Page 3 http://www.WilTec.de...
- Page 4 © by WilTec Wildanger Technik GmbH Item 61811 Page 4 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 5 Supplied parts required for assembly Flat rail Adjustable spacer Floor guide Steel hanger Anti-jump pad Door stopper Lag bolt Washer Hex wrench Junction plate © by WilTec Wildanger Technik GmbH Item 61811 Page 5 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 6 1. Put a door stop on the end of the rail; but do not screw it tight until later with the Allen key (see below). 2. Loosely attach one end of the rail to the wall. © by WilTec Wildanger Technik GmbH Item 61811 Page 6 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 7 Be careful and make sure that the hole is accurate. 2. Repeat this for the other marked posi- tions. © by WilTec Wildanger Technik GmbH Item 61811 Page 7 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 8 2. Also attach the other anti-jump disc next to the other steel bracket. Then screw both discs tight. These can prevent the door from jumping out of the rail. © by WilTec Wildanger Technik GmbH Item 61811 Page 8 http://www.WilTec.de http://www.aoyue.eu...
- Page 9 Step 11 Tilt the door slightly, lift it onto the rail and care- fully place both wheels with the grooves on top of the rail guide. © by WilTec Wildanger Technik GmbH Item 61811 Page 9 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 10 8. Repeat steps 1–3 and 1–4. Then, hold the floor guide and attach it securely by tightening the screws with a cross-head screwdriver. 9. The installation of the fitting is now com- plete. © by WilTec Wildanger Technik GmbH Item 61811 Page 10 http://www.WilTec.de http://www.aoyue.eu 2021-1...
- Page 11 Important NOTE: Reprinting, even in part, and any commercial use, including parts of the manual, only with the written consent of WilTec Wildanger Technik GmbH. © by WilTec Wildanger Technik GmbH Item 61811 Page 11 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...