Subscribe to Our Youtube Channel
Related Manuals for Imesa FLATWORK IRONER
Summary of Contents for Imesa FLATWORK IRONER
- Page 1 29/06/2022 E170301x.03_EN FLATWORK IRONER INSTALLATION AND USE INSTRUCTIONS CONSERVE FOR FUTURE CONSULTATION IMESA S.p.A. via degli Olmi 22 31040 Cessalto (TV) - Italy ITALY...
-
Page 2: Table Of Contents
29/06/2022 E170301x.03_EN SUMMARY 1. CONTENT OF THE MANUAL ……………………………………………………………………………………….3 2. SAFETY RULES……………………………………………………………………………………………………….3 3. RESPONSIBILITY OF THE MANUFACTURER………………………………………………………..…………...7 4. STORAGE AND UNPACKING………………………………………………………………………………………..7 5. MACHINE IDENTIFICATION………..……………………………………………………………………………….9 6. INSTALLATION AND POSITIONING……………………………………………………………………………….9 7. INDICATIONS ON NOISE EMISSION……………………………..……………………………………………….10 8. SMOKE EXHAUST PIPE (ONLY FOR GAS MACHINES) AND WET AIR DUCT………………………………10 9. -
Page 3: Content Of The Manual
29/06/2022 E170301x.03_EN CONTENTS OF THE MANUAL This manual is dedicated to the use of industrial drying cylinders for drying and ironing flat linen, i.e., all the linen elements that are used on plank or beds. It is drawn up in the consideration of existing Community directives. The information is addressed to the installer, the maintainer, and the user, who must be sure to have fully understood it before operating on the machine. - Page 4 29/06/2022 E170301x.03_EN ATTENTION! Always follow the ironing instructions on each item of linen with great care. ATTENTION! More connections to the machine from the outside, not carried out in a skillful manner, relieve the manufacturer of any responsibility. ATTENTION! The apparatus is not intended for use by persons whose physical or mental abilities are reduced, or with a lack of experience or knowledge.
- Page 5 29/06/2022 E170301x.03_EN The machine must always and only be used by professionally trained personnel and in the presence of at least one other operator! READ CAREFULLY AND INFORM ALL OPERATORS ABOUT INTERVENTION SYSTEMS IN CASE OF SUDDEN POWERFAILURE. DANGER OF ELECTROCUTION Any intervention on the electrical parts of the machine must be carried out only by qualified personnel and after removing the power supply to the machine.
- Page 6 29/06/2022 E170301x.03_EN The operator, when introducing the fabric into the machine, must not go with it under the hand protection. The fabric must be flattened on the entrance table, here ripples or bends must be eliminated; therefore, the fabric must be gone with on the introduction bands that will drag it between the roller and the ironing bands. It is forbidden to iron fabrics folded into several layers or several layers of overlapping fabric.
-
Page 7: Responsibility Of The Manufacturer
29/06/2022 E170301x.03_EN RESPONSIBILITY OF THE MANUFACTURER The instructions in this manual do not replace but supplement the obligations for compliance with current legislation on safety and accident prevention standards. With reference to what is reported in this manual, the manufacturer declines all responsibility if: use of the machine contrary to the laws in force on safety and accident prevention. -
Page 8: Machine Identification
29/06/2022 E170301x.03_EN To get the grille off the pallet, use two steel bars with the smallest diameter of 20 mm and a length of at least 800 mm, passing them through the prepared holes. Then harness the machine and lift it perfectly vertically. Lift the machine with the forklift and remove the pallet: finally place the machine in the final position. -
Page 9: Installation And Positioning
29/06/2022 E170301x.03_EN Tampering, removal, lack of identification plates or anything else that does not allow the safe identification of the machine, makes any installation and maintenance operation difficult and automatically voids the warranty. The washing machines described here are intended exclusively for washing fabrics in water and are intended for the commercial, professional, industrial sectors. - Page 10 29/06/2022 E170301x.03_EN ATTENTION! If the machine cannot be installed respecting the criteria below, it is necessary to request the right transformations from the manufacturer. Please note that for proper use, operation, and maintenance, it is necessary to leave a free space of at least 500 mm from the rear panel of the machine.
-
Page 11: Electrical Connection
29/06/2022 E170301x.03_EN The assembly of a manifold to unify the exhaust pipe of several machines cannot be carried out for smoke outlets: the smoke outlets must remain independent and flow outside the installation room. For machines with electric heating, it is possible to supply a collector to unify the humid air outlets: do not make "T" connections and consider the correct value of the collector section. - Page 12 29/06/2022 E170301x.03_EN Check that the supply voltage corresponds to that showed in the license plate data (voltage tolerance ±10%, frequency tolerance ±1Hz). License plate data is visible on the back of the car. For the connection use a cable of type H05 VV – F or higher sized as reported in the license plate data. The following minimum sections are suggested: 1500 1800...
-
Page 13: Leak Test (Only For Gas Cylinders)
29/06/2022 E170301x.03_EN Remove the door. Pass the power cord through the hollow press on the left shoulder of the grille. The power supply must be carried out by connecting the cable to a series of terminals (already present in the appliance): Depending on the type of power supply provided by the serial number plate of the machine, connect the wires to the disconnector contacts marked as follows: : terminal for the equipotential connection with the grounding system of the user. -
Page 14: Gas Connection: Inlet Pressure Control (Only For Gas Cylinders)
29/06/2022 E170301x.03_EN If the preparation of the appliance does not correspond to the family of gas available on site, it is mandatory to carry out a transformation of the appliance for adaptation to the type of gas present. In this case it is absolutely necessary to inform the authorized technical service center. - Page 15 E170301x.03_EN 29/06/2022 Nozzle Primary 1500 DEVELOPING COUNTRIES Nozzle diameter1/100 Power.kW pressure[mbar] diaphragm AL, BA, BG, HR, MK, UADK, FI, SE, BG, EE, LV, LT, CZ, SI, TR, HR, RONOLU, PLNLES, GB, GR, IE, IT, PT, C=20 22,41 SKFR, BEDEAT, CHHU FR, BE 18,8 C=20...
- Page 16 E170301x.03_EN 29/06/2022 Nozzle Primary 1800 DEVELOPING COUNTRIES Nozzle diameter1/100 PowerkW pressure[mbar] diaphragm AL, BA, BG, HR, MK, UADK, FI, SE, BG, EE, LV, LT, CZ, SI, TR, HR, RONOLU, PLNLES, GB, GR, IE, IT, PT, A=30 24.79 SKFR, BEDEAT, CHHU FR, BE 18,9 B=25...
- Page 17 E170301x.03_EN 29/06/2022 Nozzle Primary 2100 DEVELOPING COUNTRIES Nozzle diameter1/100 PowerkW pressure[mbar] diaphragm AL, BA, BG, HR, MK, UADK, FI, SE, BG, EE, LV, LT, CZ, SI, TR, HR, RONOLU, PLNLES, GB, GR, IE, IT, PT, B=25 26,8 SKFR, BEDEAT, CHHU FR, BE 18,6 B=25...
-
Page 18: Gas Connection: Test
29/06/2022 E170301x.03_EN GAS CONNECTION: TESTING As soon as the connection work is completed, the appliance and the entire installation must be checked. In particular, check: that the connections are made by the requirements and indications of this manual. that all the safety requirements of the standards, laws and directives in force are met. that the gas connections made are watertight. -
Page 19: What To Do In Case Of Entrapping
29/06/2022 E170301x.03_EN ATTENTION! The formation of yellow stains on the stretched fabrics, signals the presence of detergent not carefully eliminated during rinsing! The formation of folds on the stretched fabrics can be generated by too low residual moisture. Also pay attention to the thicknesses of the fabrics. -
Page 20: What To Do In Case Of Lack Of Electricity
29/06/2022 E170301x.03_EN ATTENTION! If the temperature of the roller is high (above 80°C), continue to insert wet fabrics over the entire length of the roller, and continue to rotate the roller by hand, to avoid burning of the ironing bands. Once completed, close the door with the key and wait for the return of the power supply. -
Page 21: Start And Stop
29/06/2022 E170301x.03_EN ATTENTION! All users must be informed of this procedure and be aware of the operation of the machinery's safety systems. USING THE EMERGENCY BUTTON In case of emergency and need for a quick stop of the machine, press the emergency button on the side of the machine. When the emergency button is pressed, the ironing roller stops at the same time the lay is lifted. - Page 22 29/06/2022 E170301x.03_EN Below is a detailed description of the programming parameters that may appear in the preview phase: HEATING It is the temperature set for the ironing cycle. Please note that the choice of temperature must be made by referring to the specific characteristics of the fabric. The definition of temperature is also related to the choice of roller speed.
-
Page 23: How To Use Cooling
29/06/2022 E170301x.03_EN At the first achievement (after switching on) of the set temperature value, the buzzer emits some beeps, to warn the user. In any case, do not start the ironing work until the minimum temperature of 80 ° C is reached. At the end of the ironing cycle, the machine must be stopped by pressing the COOL DOWN button: in this case the machine will continue to keep the roller in rotation until it reaches 80 °... -
Page 24: The Gas Reset Button
29/06/2022 E170301x.03_EN THE GAS RESET BUTTON For machines with gas heating, there is a reset button on the push-button panel that allows you to restore any blocks of the flame control unit. In the event that the igniter does not ignite the gas, the microprocessor signals the block through the "flame lack" display signal, alternating with the invitation to press the RESET gas button. -
Page 25: Display Messages And Malfunctions
29/06/2022 E170301x.03_EN At the end of the work cycle and in any case always, when the machine is not in operation, remember to detach all the power supplies in the following order: gas supply (if any): close the supply power supply: open, bringing them from position "1" to position "0", the electrical switch(s) placed on board the machine. -
Page 26: Reports Of Malfunction
29/06/2022 E170301x.03_EN MESSAGE / EFFECT POSSIBLE CAUSE Check if: As soon as you press the START button, the machine one of the "ENGINE THERMAL" or "GAS starts but stops immediately, and the display remains the PRESSURE" alarms intervened at a temperature word "OFF"... -
Page 27: Programming
29/06/2022 E170301x.03_EN PROGRAMMING It is possible to perform a series of changes to the default data by entering the user menu. To log in, while the machine is stationary press the ":" menu icon at the top right. The screen appears on the display: Enter the 6-digit code for access to the user area (default password): "123456". - Page 28 29/06/2022 E170301x.03_EN Entering within SETTINGS you can choose the following functions: CHANGE LANGUAGE: to define the communication language of the touch screen. SET DATE: to adjust the local date. SET TIME: To adjust the local time. TEMPERATURE °C/°F: to decide the display of the temperature in °C or °F. DISABLE TOUCH: to decide that, while using the machine, the only active button on the keyboard is the STOP button (it is therefore impossible to change the parameters of the program in progress).
- Page 29 29/06/2022 E170301x.03_EN Do not allow the accumulation of threads around the machinery. For daily cleaning use a soft, moistened cloth. Do not use abrasive products, abrasive sponges, solvents, or metal objects. EVERY DAY: Remove any dust or fabric residues that may have settled on the temperature probe holder, so as to maintain good contact between the support plate and the surface of the ironing roller.
-
Page 30: Burner Cleaning (For Gas Cylinders)
29/06/2022 E170301x.03_EN Pinch one of the metal hooks at the end of the band to prevent the Nomex wire from slipping off. Remember to insert the bands in the correct direction and direction (weaving in Nomex outwards and cutting at 45 ° downwards). Tension the introduction bands as described above. -
Page 31: What To Do In Case Of Prolonged Downtime
29/06/2022 E170301x.03_EN WHAT TO DO IN CASE OF PROLONGED DOWNTIME Cover the roller with paraffin after removing the top cover or close the roller with oiled paper. EXPLODED AND SPARE PARTS For the consultation of the electrical diagrams, the exploded and for the identification of spare parts, please refer to the manufacturer's website, within the Technical Area.
Need help?
Do you have a question about the FLATWORK IRONER and is the answer not in the manual?
Questions and answers