Table of Contents
Advertisement
Quick Links
MG300 Media Gateway
Easily Bridges Most IP Protocols
Contents
◼
Packing List
◼
Device interfaces and functions
◼
Device connection, login and applications
◼
Device upgrade and restore the factory settings
Before using this product, it is recommended that you read the guide carefully. To ensure your personal safety and avoid physical or electrical damage to the
device, please strictly follow the instructions of this guide to install and use it under the guidance of professionals. Incorrect electrical connections or physical
installation may cause permanent damage to the device and even threaten personal safety.
Leading solution provider of IP-based video transmission
Quick Start Guide
Advertisement
Table of Contents
Related Manuals for Kiloview MG300
Summary of Contents for Kiloview MG300
- Page 1 Leading solution provider of IP-based video transmission Quick Start Guide MG300 Media Gateway Easily Bridges Most IP Protocols Contents ◼ Packing List ◼ Device interfaces and functions ◼ Device connection, login and applications ◼ Device upgrade and restore the factory settings Before using this product, it is recommended that you read the guide carefully.
-
Page 2: Packing List
1 Packing List (1) MG300 ×1 (2) Power Supply ×1 (3) Warranty Card ×1 (4) Quick Start Guide ×1 2 Device Interfaces USB expansion port Working Indicator SDI output Power port Reset 1000M Ethernet port 3.5mm line in /out HDMI output... -
Page 3: Led Indicators
Network abnormal/not connected Working White Device is abnormal or not started 4 Application IP stream AC100~240V Power supply DC12V Switcher SDI Monitor HDMI Monitor Note 该场景下网络线缆连接 MG300 设备的网口 1（NET 1） ！ ⚫ MG300 最多支持 9 路画面解码，HDMI 和 SDI 可输出相同或者不同画面！ ⚫... - Page 4 Connect your Ethernet cable to NET 1 port. ⚫ MG300 supports up to 9-channels decoding, HDMI and SDI output same or different contents. 5 Login to the device webpage Login to the device webpage via the default IP address 192.168.1.168. That is, enter http://192.168.1.168/ in the browser to access the web page.
- Page 5 After change the device IP, please restore the computer network to the working network IP address. ⚫ If the MG300 device is connected to the network by Ethernet port 2, the default IP address is: 192.168.2.168! The username and the password are admin by default.
- Page 6 6 Decoding and output 6.1 Add video source In the lower left of the "Media", click "Add", and then select the "Source Type" and configure the parameters in the pop-up dialog box, and click "OK" to add the video source to the video list. Introduction ⚫...
- Page 7 For more information about how to add the video source, please refer to: https://www.kiloview.com/en/support/docs/MG300/ 6.2 Preview The added sources will be displayed in the “Video Source”, drag the source to the upper “Source Preview” window to preview the source images and to configure the output parameters.
- Page 8 6.3 Output There are two output windows on the MG300 webpage. You can select SDI or HDMI to decode and output the same or different content in the upper right corner of the window. Drag the video source into the output window, that is, output with the selected SDI or HDMI interface.
- Page 9 2. Click “Service”- “Add Stream Service”, and then choose the “Service Type”. For more information about the stream service, please refer to: https://www.kiloview.com/en/support/docs/MG300/...
-
Page 10: Firmware Upgrading
Select “video decoders” > “MG300”, find and download the latest firmware 8.2 Upgrade firmware Login to the web page of MG300, click "Settings"-- "Firmware Upgrade" to check whether the latest firmware version downloaded is higher than your current version. If yes, select the downloaded firmware and click "Firmware Upgrade". -
Page 11: Restore Factory Settings
9 Restore factory settings If the device cannot work normally after modified the parameters or forgot internet IP configuration and couldn’t search and find the device, please restore factory settings. Two methods for restoring factory settings: 1) If you can login to web page, then via the WEB page, click "Settings—System settings--Restore factory settings". - Page 12 10 Others To prolong the device life，please unplug the power and keep it properly if you do not use it for a long time. For more questions, please contact us via： https://www.kiloview.com/en/support KILOVIEW Electronics CO., LTD. Tel：86-18573192787 Email：support@kiloview.com Web：www.kiloview.com/en Address: B4-106/109, Jiahua Intelligence Valley Industrial Park, 877 Huijin Road, Yuhua District,...
Need help?
Do you have a question about the MG300 and is the answer not in the manual?
Questions and answers