Related Manuals for Hisense RW54N1SSD
Summary of Contents for Hisense RW54N1SSD
- Page 1 Wine Cooler SERVICE MANUAL CAUTION BEFORE SERVICING THE UNIT, READ THE "SAFETY PRECAUTIONS" IN THIS MANUAL. MODEL: RW54N1SSD,RW46N1DSD...
-
Page 2: Table Of Contents
CONTENTS SAFETY PRECAUTIONS ............................... 2 PARTS IDENTIFICATION ...............................3 DISASSEMBLY................................... 4-8 DOOR ....................................4 SHELVES....................................4 LAMP………… ..................................4 MAGNETIC SWITCHE..............................4-5 DISPLAY BOARD BOX ASSEMBLY ..........................5-6 CONTROL BOARD & TRANSFORMER ..........................6 SENSOR & FAN................................6-8 TROUBLESHOOTING............................... 9-12 COMPRESSOR COMPONENTS ............................9 ANOTHER ELECTRIC COMPONENT .......................... -
Page 3: Parts Identification
2. PARTS IDENTIFICATION Model：RW54N1SSD Model：RW46N1DSD - 3 -... -
Page 4: Disassembly
BOLT Figure 1 3-2 SHELVES Figure 4 (Models：RW54N1SSD) The sides of the shelves are equipped with protective stoppers which prevent bottles from falling from the shelves. 3-3 LAMP When removing / inserting the shelves from / into the rails,... -
Page 5: Display Board Box Assembly
Bottom gill magnetic switch Figure 13 3-5 DISPLAY BOARD BOX ASSEMBLY (Models：RW54N1SSD) 2. Insert a screwdriver on the left hole. (Figure 14) 1. Loosen the screws. (Figure 10) Figure 14 Pull forward the claw and raised the Display board box Assy a bit. -
Page 6: Control Board & Transformer
3. DISASSEMBLY The Display board box Assy. (Figure 17) 3-7 SENSOR & FAN (Models：RW54N1SSD) 1. Loosen 6 screws. Pull out the rear air duct cover. (Figure Figure 17 Screws Display board box Display board 3-6 CONTROL BOARD & TRANSFORMER Loosen the screws. Pull out the Control board box. (Figure... - Page 7 3. DISASSEMBLY (Model：RW46N1DSD) 5. Loosen 6 screws. Pull out the rear air duct cover. (Figure 1. Remove the display board box Assy according 3-5 2. Separate the top plate of middle separator. (Figure 25) Figure 25 Figure 28 6. Separate the lead wire Housings. (Figure 29) 3.
- Page 8 3. DISASSEMBLY 10. Separate the sensor. (Figure 33) Press the nails with screwdriver at the back of the rear air duct cover. (Figure 31) Figure 33 Figure 31 9. Separate the sensor cover. (Figure 32) Figure 32 - 8 -...
-
Page 9: Troubleshooting
4. TROUBLESHOOTING 4-1 COMPRESSOR COMPONENTS Check the Check the resistance resistance of among M-C（about Motor 6Ω), S-C（about 6Ω) Replace Compressor. Compressor. and M-S（about 12Ω) in Motor Compressor. Check the resistance Check the of two terminals in Replace resistance of PTC-Starter. PTC-Starter. -
Page 10: Another Electric Component
4-2 ANOTHER ELECTRIC COMPONENTS ▼ Cooling is impossible Compressor doesn't run. Check if current flows to Cause. the following components. a. Starting devices Shorted or broken. Poor contacting b. OLP or shorted. c. Compressor coil Coil shorted. Replace Poor contacting d. -
Page 11: Service Diagnosis Chart
The door was reversed and not properly installed. The gasket is dirty. The shelves are out of position. Models： ):The defrost sensor is failed. RW54N1SSD Display error code “E3” or “E4”. Display error code “E7” or “E8”. Models： RW46N1DSD ):The lower zone sensor is failed. -
Page 12: Refrigerating Cycle
4-4 REFRIGERATING CYCLE ▼ Troubleshooting Chart TEMPERATURE STATE OF STATE OF THE CAUSE REMARKS OF THE THE SET EVAPORATOR COMPRESSOR • A little Refrigerant PARTIAL Appliance Low flowing sound of A little high LEAKAGE Refrigerant is heard and more than discharges. -
Page 13: Description Of Control Pcb
5. DESCRIPTION OF CONTROL PCB (Models：RW54N1SSD) (Figure 34) Figure 34 (Model：RW46N1DSD) (Figure 35) Figure 35 - 13 -...