Table of Contents
Advertisement
3.2 Description of the machine and its parts
Fig. 2
The drum mower (
drive unit is attached to the mower flange. On the left hand side of the handlebar, there is the
controls the machine's forward travel. The
the slot on the left side of the cover. The travel is ensured by a worm gearbox with a belt clutch, which secures the smooth
transmission of the force (the machine does not roll through) to the wheels
plastic gearbox cover
12
against mowed flying growth by the plastic cover
side cover
4
, which is attached by its screw connection
4 Operating Instructions
4.1 Machine Assembly
Request the machine unpacking and training from your seller as a part of his pre-sale service!
Gripping points when unpacking (from the box) (per
unit connection component
It is forbidden to lift an assembled machine by its front plastic cover. The cover is not
dimensioned for the machine weight.
4.1.1 Machine Assembly Procedure
Assemble the machine per the following procedure:
1)
Following
at its gripping points at the front
2)
Remove the M5 self-locking factory-installed self-locking nuts (2 pieces) with their washers, and attach the
disc cover to the machine so that the holes in the cover match the frame screws and the tapered section of
the cover is inserted under the engine plate. Return the M5 nuts and washers to the screws and tighten the
nuts.
3)
Following
side (longer) cover
holes in the cover holder and secure both covers against sliding by tightening the strips.
4)
Following
the frame. Tighten the mounting screw by hand and check that the side cover does not fall spontaneously.
4.1.2 Attaching and removing the drive unit
The process of attaching a drive unit is described in the operating instructions for the drive units. The attachment,
clamping, and removal process, as well as safety instructions, do not differ from other adapters and, therefore, this information
is not provided in this manual.
Before installing the drive unit, make sure the inner face of the clutch disc in the drive flange is
not dirty or greasy. Dirt or grease could make the centrifugal clutch slip, and that could lead to reduced
mowing performance and increased risk of wear and failure of the centrifugal clutch.
4.1.3 Control lever mounting
After installing and securing the drive unit in the drive flange, install the travel pulley lever (see
control lever is mounted on the left handle through the holder and M6 wing nuts. Install the lever so that it is possible to
operate the ignition safety lock latch. Move the lever slightly to the left/right (approx. 5° from the vertical plane) during the
assembly to make sure it is within your fingers' reach.
Lead the bowden cable over the top of the handlebars. Its route should be smooth and radius bends as large as possible.
Attach the bowden cable to the handle bar in the area between the upper joint sides together with the gas bowden cable with
the supplied 7.6x200 (14) release strap (see
4.2 Machine Operation
4.2.1 Engine Starting
The drive unit motor is started as described in the drive unit operating instructions.
When starting the engine, both control levers (
Fig. 3
)!
Do not leave the machine after starting the engine!
4.2.2 Starting the cutting disc
Make sure that all persons (children!) are at a safe distance from the machine! Otherwise, do not
continue with this process!
) is built on its steel frame, to which all the critical components of the machine are attached. The
1
disc drive pulley lever that turns ON and OFF the cutting disc drive is located in
. At the front, there is the cutting disc
8
and
1
.
Fig.1
- remove the disc cover
4
Fig. 1
- attach the rear (shorter) side cover
6
to the longer cover holder arm
Fig. 2
- unscrew fastening screw
Fig. 2
).
11
5
with its four steel blades
7
. The mowed growth trimming is secured through the removable
3
.
Fig. 1
): in the front, the cutting disc
(We recommend completing the assembly by two persons)
3
from the box, bag
and in the rear
1
, and remove it from the box.
6
to the shorter cover holder arm
2
. Draw the tightening strips (2 pieces) through the
3
, making sure side cover
1
and
2
in
Fig. 2
5
Drum Mower
2
travel pulley lever, which
. The clutch gearbox is covered with the
6
. The operator is protected
4
, in the rear, behind the drive
6
, and side cover
2
. Grasp your machine
2
, and attach the
4
may easily slide into the slot in
Fig. 2
). The travel pulley
) must be in the "OFF" position (see
Advertisement
Table of Contents
