Roberts Rambler BT Quick Start Manual

Wha t is in the Box ?
Radio, mains adaptor, quick start guide and safety/warranty leaflet.
Features
• Bluetooth audio streaming from smartphone, tablet or laptop
• DAB / DAB+ / FM RDS wavebands
• Eco power saving mode
• Clock and alarm functions available with battery power
• 20 radio station presets (10 DAB and 10 FM)
• Multi level display dimmer
• 2 alarms with humane wake
• Sleep and snooze timers
• Battery or mains operation via AC adaptor (included)
• Batteries 4 x C size / LR14 (not included)
• Auxiliary input and headphone socket for private listening
Controls
2 3 4 5 6 7
Mode Auto Tune Dimmer Info/Menu
1
11
1
13
1 Volume control 10 Tuning / Select control
2 Headphone socket 11 LCD display
3 On / Off / Sleep button 12 Loudspeaker
4 Mode button 13 Telescopic aerial
5 Auto Tune / Bluetooth Pair button 14 DC input socket
6 Dimmer button 15 Battery compartment
7 Info / Menu / Alarm 1 button 16 USB socket (in battery compartment,
for service use only)
8 Preset / Alarm 2 button
9 Auxiliary input socket
• It is recommended that the DAB band be used wherever possible as better results in terms of
quality and freedom from interference will usually be obtained than on the FM band.
S T EP 1 - P l u g i n & p l a y D A B r a d i o
A - Connect to the mains
Please read the safety leaflet provided before connecting
your radio to the mains.
1 Place your radio on a flat surface.
2 Fully extend the telescopic aerial located on the rear of
the radio.
3 Plug the cable from the mains adaptor into the DC input
socket. Plug the mains adaptor into a wall socket and
switch on the socket.
4 A start up screen will be displayed and a station scan will
be performed. The clock will set.
Note: If no signals are found it may be necessary to relocate
your radio to a position giving better reception and carry
out a scan for new stations.
B - Switch on your radio
1 Press and release the On/Off button to switch on the radio.
After each use the radio will remember the mode used and
then switch on in that mode the next time it is used. To switch
off your radio press the On/Off button.
8 9
Preset
2 If this is the first time the radio is used a scan of the Band
Aux In
III DAB channels will be carried out (depending on whether
2
a scan was completed in standby mode).
10
C - Select a DAB radio station
1 If needed, press and release the Mode button until the
DAB mode is selected.
12
2 Rotate the Tuning control to step through the list of available
DAB stations.
3 Press the Tuning control to select the station.
4 Adjust the Volume.
5 Some radio stations may have one or more additional
broadcasts associated with them. If these are available
they will appear immediately after the main station.
• Press and release the Info / Menu button to cycle through
the various DAB display options.
The display options are station name, scrolling text,
program type, signal strength (the minimum signal marker
( ) shows the minimum signal strength needed for good
DAB reception), multiplex name, frequency, bit rate, time
DC 5.9V
14 or date.
All displays except the text display will revert to the clock
display after 10 seconds.
D - Scan for DAB stations
As time passes new stations may become available or you may
have moved to a different part of the country.
16 15
1 Press and release the Auto Tune button.
2 Your radio will perform a scan of the Band III DAB channels.
As new stations are found, they will be added to the list
stored in the radio.
Menu options
1 You can access your radios menu system by applying
a long press on the Info / Menu button.
2 Rotate and press the Tuning / Select control to select
menu options.
3 To exit menu options press the Info / Menu button as
needed.
Search tuning - FM
1 Carefully, fully extend the telescopic aerial.
2 Press and release the Mode button until FM is selected.
DC 5.9V
Rotate the Tuning control clockwise or anti-clockwise and
3
then press and release the Auto Tune button. Your radio
will scan upwards (low to high frequency) or downwards
(high to low frequency) and will stop automatically when
it finds a station of sufficient strength.
4 If the signal is strong enough and there is RDS data
present then the radio will display the station name.
5 Adjust the Volume.
• Press and release the Info / Menu button to cycle through
the various FM display options. The display options are
station name, scrolling text, program type, frequency
time or date.
To manual tune, rotate the Tuning control to tune to a
station. The frequency will change in steps of 50 kHz.
Preset radio stations
You may store your preferred DAB or FM radio stations to the preset station memories. There are 20 memory
presets, 10 for DAB and 10 for FM. Presets are remembered by the radio in the event of a power failure.
To store a preset
1 Ensure your radio is switched on.
2 Tune to the required radio station.
3 Apply a long press on the Preset button.
Mode
4 Rotate the Tuning control to select the desired station
number under which you wish to store the station.
5 Press the Tuning control. The display will show for example,
'P1 SAVED'. Repeat this procedure for the remaining
presets. Presets may be overwritten by following the above
procedure.
To recall a preset
1 Choose DAB or FM mode.
2 Press and release the Preset button.
3 Use the Tuning control to select the desired preset. Your
radio will tune to the station stored in the preset memory.
Note: The display will show 'Empty' if no station has been
stored to that preset.
Info/Menu
1 Ensure Bluetooth is enabled on your smart device.
1
2 Ensure your radio is switched on.
3 Press and release the Mode button until the Bluetooth
mode is selected on your radio. The Bluetooth indicator
Auto Tune
will flash and your radio will show that it is 'discoverable'.
4 On your smart device select 'Rambler BT'. Once the
connection is established the indicator will remain steady.
You may now play your music.
Adjust the volume using the Volume control on the radio
5
and on the connected Bluetooth device. If you find the
volume from the radio is not sufficient, it may be that
the volume setting of the connected device needs to be
increased.
6 The audio player in your smart device may be able to
respond to the Play/Pause, Next or Previous track on
the radio. Press the Tuning control to pause playback.
Press the control again to resume playback. Rotate the
control clockwise or counter-clockwise to skip to the next
Info/Menu
or previous track.
Note: Not all player applications or devices may respond
to all of these buttons.
7 To connect a different device press and release
1
the Bluetooth Pair button. Your radio will become
discoverable by other devices.
S TE P 2 - P l a y F M r a d i o
Mode
Preset
ST E P 3 - B l u e t oo t h
Mode
Auto Tune
continued overleaf...
Auto Tune