Page 1
LCD-TV Chassis : N82C Model LE19C45*** LE22C45*** SERVICE Manual TFT-LCD TV Contents 1. Precautions 2. Product specifications 3. Disassembly and Reassembly 4. Troubleshooting 5. Exploded View & Part List 6. Wiring Diagram LE19C45***/LE22C45*** Refer to the service manual in the GSPN (see the rear cover) for the more information.
1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1. Precautions 1-2. Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1. Precautions 1-4. Installation Precautions For safety reasons, more than a people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
2. Product specifications 2-2. Specification Comparison to Old Models O : application, X : non-application ※ Model LC4E(LE19/22C45***) LB4C(LE19/22B45***) Design Display Type LCD TV LCD TV Built-in Tuner Resolution 1360 x 768 1360 x 768 LCD Panel TFT LCD Panel 50Hz TFT LCD Panel 50Hz Screen Size 19"/22"...
2. Product specifications 2-3. Detail Factory Option If you replace the main board with new one, please change the factory option as well. ※ The options you must change are “Type”. Model Name LE19C45*** LE19C45*** LE19C45*** LE22C45*** LE22C45*** Vendor INNOL Panel CODE BN07-00766A...
Code. No Remark Remote Control & Batteries BN59-01012A (AAA x 2) Power Cord 3903-000456 22": BN96-12739B Stand (BN90-02433B) Samsung Electronics Service center Screw 6002-001294 (for the stand - M4) (22" Only) Owner’s Instructions BN68-02591A Cleaning Cloth BN-63-01798B Warranty Card / Registration...
3. Disassembly and Reassembly 3. Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the LE19/22C450 LCD TV. WARNING: This LCD TV contains electrostatically sensitive devices. Use caution when handling these components. 3-1. Disassembly and Reassembly Cautions: 1.
Page 16
3. Disassembly and Reassembly Description Picture Description Screws 3. Remove screws and disconnect conectors. 19 inch 19 inch : 6 screws 22 inch : 8 screws 6003-000269 (M3 x L6, TAPTYPE) 6003-001439 (M4 x L8, TAPTYPE) 22 inch 6002-001294 (M4 x L16, Tapping) 4.
Page 17
3. Disassembly and Reassembly Description Picture Description Screws 5. Lift up the panel. 19 inch 22 inch Reassembly procedures are in the reverse order of disassembly procedures. ※ Screw Size Code No. A (mm) B (mm) C (mm) Q’ty 6002-001294 8.3±0.5 16±0.8 3.85~4.0...
4. Troubleshooting 4. Troubleshooting 4-1. Troubleshooting 4-1-1. Previous check Check the various cable connections first. • Check to see if there is a burnt or damaged cable. • Check to see if there is a disconnected or loose cable connection. •...
Page 19
4. Troubleshooting 4-1-2. No Power The LEDs on the front panel do not work when connecting the power cord. Symptom The SMPS relay does not work when connecting the power cord. The units appears to be dead. The IP relay or the LEDs on the front panel does not work when connecting the power cord if the cables are improperly connected or the Main Board or SMPS is not functioning.
Page 20
4. Troubleshooting Power CN2001 Dimming out A13V Panel Setting...
Page 21
4. Troubleshooting 4-1-3. No Video (Analog PC signal) Symptom Audio is normal but no picture is displayed on the screen. Check the PC source Major Check the Arsenal, Check the Chelsea. checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Check a set Power indicator LED is off.
Page 24
4. Troubleshooting 4-1-4. No Video (HDMI - Digital Signal) Symptom Audio is normal but no picture is displayed on the screen. Check the HDMI source. Major Check the HDMI switch, Check the Chelsea. checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Power Indicator is off.
Page 27
4. Troubleshooting 4-1-5. No Video (Tuner_CVBS) Symptom Audio is normal but no picture is displayed on the screen. Check the Tuner CVBS source. Major Check the Tuner, Check the Chelsea. checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Is power inductor LED off? Check a set Lamp(Backlight) on and no video?
Page 30
4. Troubleshooting 4-1-6. No Video (Tuner DTV) Symptom Audio is normal but no picture is displayed on the screen. Check the DTV source. Major Check the Tuner, Check the Chelsea. checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Power indicator LED is off.
Page 33
4. Troubleshooting 4-1-7. No Video (Video CVBS) Symptom Audio is normal but no picture is displayed on the screen. Check the Video CVBS source Major Check the Chelsea. checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Power indicator LED is off.
Page 36
4. Troubleshooting 4-1-8. No Video (Component) Symptom Audio is normal but no picture is displayed on the screen. Check the Component source Major Check the chelsea. checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Power indicator LED is off.
Page 39
4. Troubleshooting 4-1-9. No Sound Symptom Video is normal but there is no sound.. When the speaker connectors are disconnected or damaged. Major When the sound processing part of the Main Board is not functioning. checkpoints Speaker defect.. Check the source and Input the sound source properly.
4. Troubleshooting 4-2. Alignments and Adjustments 4-2-1. General Alignment Instuction Usually, a color LCD-TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. Use the specified test equipment or its equivalent. Correct impedance matching is essential.
4. Troubleshooting 4-3. Factory Mode Adjustments 4-3-1 Entering Factory Mode To enter ‘Service Mode’ Press the remote -control keys in this sequence : - If you do not have Factory remote - control Power OFF INFO MENU MUTE 4-3-2 How to Access Service Mode Using the Customer Remote Turn the power off and set to stand-by mode.
Page 44
4. Troubleshooting 4-3-3 Factory Data Option Factory OPTION Data Range Name Factory Reset NONE/19O6TH0C/19A6TH0C/22I6TH0C/22A6TH0C/22 D6TH0C/22P6TH0C/26A6AH0C/26D6AH0C/26L6AH0C /26P6AH0C/32A6AH0C32D6AH0C/32L6AH0C32P6AH0 Select Panel C/32A6AF0C/32L6AF0C/32A1AF0C/32L1AF0C/37L6AF Type 0C/37L1AF0C/40A6AF0C/40D6AF0C/40L6AF0C/40A1A 12 : inch F0C/40L1AF0C/40A1UF0C/40D1UF0C/40L1UF0C/46A6 3 : vendor AF0C/46D6AF0C/46L6AF0C/46A1AF0C/46L1AF0C/46A Type 4 : refresh 1UF0C/46D1UF0C/46L1UF0C/55A1UF0C/55L1UF0C/6 5 : POL 5L1UF0C/19R6TH0E/22D6TH0E/26D6AH0E/32D6AH0 6 : resolution E32D6UF0E/32A1UF0E/32D1UF0E/37L6UF0E/37D1UF 7 : multi 0E/37L1UF0E/40D6UF0E/40A1UF0E/40D1UF0E/46D6...
Page 45
4. Troubleshooting Control Factory Name Data Range Control EDID Sub Option Shop Option Sound Factory Name Data EDID EDID ON/OFF EDID WRITE ALL … EDID WRITE PC … EDID WRITE … HDMI EDID WRITE … Download EDID data to EEPROM. HDMI1 1.
Page 46
4. Troubleshooting Factory Name Data Range Hotel Option Hotel Mode SI Vender … Power On … Channel Channel Type … Power On Volume … Min Volume … Max Volume … Panel Button Lock … Power On Source … Factory Name Data Range Shop Option...
Page 47
4. Troubleshooting Factory Name Data Range Test Pattern Panel Auto Setting Panel Display fixed Time Logic Usb D/L Tuner Status Factory Name Data Range Test Pattern Test for Input of Scaler. OFF/ White/Grey/Black Pattern Sel If you can see pattern well, there is Red/Green/Blue problem at input of Scaler.
Page 48
4. Troubleshooting ISDB-T FFT Size_1 Not modified Guard Interval_1 Not modified Freq. Offset_1 Not modified SNR_1 Not modified IF AGC_1 Not modified TMCC Lock_1 Not modified TS Packet_1 Not modified Master Lock_1 Not modified A_Modulation_1 Not modified A_Code Rate_1 Not modified A_Timer Not modified InterLeave_1...
Page 49
4. Troubleshooting ADC/WB Factory Name Data Range ADC/WB ADC Target ADC RESULT Factory Name Data Range AV Calibration Success Success / Failure Comp Calibration Success Success / Failure PC Calibration Success Success / Failure HDMI Calibration Success Success / Failure Factory Name Data Range...
4. Troubleshooting 4-4. White Balance - Calibration 4-4-1 White Balance -Calibration 1. Calibration AV Calibration Comp Calibration PC Calibration HDMI Calibration 4-4-2 White Balance - Adjustment (low light) (hight light) Sub Bright Sub Contrast 3. W/B R offset R gain G offset G gain B offset...
4-6. Servicing Information 4-6-1 USB Download Method Samsung may offer upgrades for TV’s firmware in the future. Please contact the Samsung call center at 1-800- SAMSUNG (726-7864) to receive information about downloading upgrades and using a USB drive. Upgrades will be possible by connecting a USB drive to the USB port located on your TV.
4. Troubleshooting 4-7. How To Upgrade Sub Micom With Ddc Manager 4-7-1. TV Sub S/W Order Description Connect DDC MANAGER to the TV Set with D-SUB cable. And Power on. (USB type : MTI-2510 / parallel type : MTI-2059) Enter the factory mode. Control - EDID - EDID ON/OFF Select ON.
Page 54
4. Troubleshooting Order Description Push the ‘Program’ Button. (It takes quite a bit of time. You can wait or close the DDC tool by force and open tool and load file again.) Push the ‘Program’ Button again. (It takes about 100 seconds.) If update completes, TV set will booting automatically.
4. Troubleshooting 4-8. Mechanical diagram 4-8-1. 19LB450 Size (W×D×H) [mm] Set [mm] 1) Set with Stand : 461.3 x 180.2 x 348.0 2) Set without Stand [mm] : 461.3 x 59.2 x 309.1 3) Opening Size [mm] : - Package(Outside Dimension) [mm] : 530 x 430 x 172 Weight [kg] Set with Stand Stand(Only)
5. Exploded View & Part List 5. Exploded View & Part List 5-1. LE19C450E1W Exploded View R001A SP01A SP01A M0014 P001A AC271 T0447 PANEL SB04A F001A...
Page 59
5. Exploded View & Part List 5-2. LE19C450E1W Parts List Location No. Code No. Description & Specification Q’ty S.A/S.N.A Remark SB04A BN96-04794F ASSY STAND P-BASE;LC450 19,PC+ABS,V0,BK0 AC271 BN63-05259C COVER-MAIN;LC450,EO,PC+ABS,V0,BK0008 F001A BN96-12730B ASSY COVER P-FRONT;LC450 19,EO,PC+ABS,V0 M0014 BN94-02707D ASSY PCB MAIN;LE19C450E1WX* P001A BN44-00328B AC VSS(I)-LIPS;FSP035-2PI10,E19HD_AFS,6.
Page 60
5. Exploded View & Part List 5-2-1. LE19C450E1W Parts List Service Bom (SA: SERVICE AVAILABLE, SNA: SERVICE NOT AVAILABLE) Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark S001A BN90-01509C ASSY STAND;LC450,EO,BLACK SB04A BN96-04794F ASSY STAND P-BASE;LC450 19,PC+ABS,V0,BK0 ...3 M0081 6003-001001...
5. Exploded View & Part List 5-2. LE19C450E1W Parts List Location No. Code No. Description & Specification Q’ty S.A/S.N.A Remark SB04A BN96-04794F ASSY STAND P-BASE;LC450 19,PC+ABS,V0,BK0 AC271 BN63-05259C COVER-MAIN;LC450,EO,PC+ABS,V0,BK0008 F001A BN96-12730B ASSY COVER P-FRONT;LC450 19,EO,PC+ABS,V0 M0014 BN94-02707D ASSY PCB MAIN;LE19C450E1WX* P001A BN44-00328B AC VSS(I)-LIPS;FSP035-2PI10,E19HD_AFS,6.
Page 68
5. Exploded View & Part List 5-2-1. LE19C450E1W Parts List Service Bom (SA: SERVICE AVAILABLE, SNA: SERVICE NOT AVAILABLE) Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark S001A BN90-01509C ASSY STAND;LC450,EO,BLACK SB04A BN96-04794F ASSY STAND P-BASE;LC450 19,PC+ABS,V0,BK0 ...3 M0081 6003-001001...
6. Wiring Diagram 6-3. Connector Functions Connector Functions ↔ Supply main power and dimming signal from IP board to Main Board. CN801 CN2001 ↔ The LVDS signal transfered from Main Board to Panel. FCN402 CN1403_HD 6-4. Cables Main - TCON 19": BN96-12447P (180mm) Code 22": BN96-12447R (180mm)