Westinghouse W-395 Owner's Manual

Owner's Manual
Indoor Lighting Fixture
Installation Instructions
WARRANTY INFORMATION
This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a
period of Five Years from purchase date. This warranty is in lieu of all other warranties expressed or
implied.
This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration
of components, nor does it cover damages caused through abuse, improper installation, surges in
electric current, or acts of third parties.
This warranty does not cover costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, contact us toll free at 1-888-417-6222.
WARNING:
ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.
Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essen-
tial for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not dam-
age electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are
damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are pro-
vided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985
have supply wires rated 60° C. Consult a qualified electrician before installing.
NOTE: For fixture employing a grounded convenience outlet. This fixture employs a grounded
type receptacle and is not intended for connection to a two wire ungrounded source of supply.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many
years of beauty and service. For questions and comments, please visit www.westinghouselighting.
com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any pack-
ing materials (see figure 1).
FIGURE 1.
GROUND
*OUTLET
WIRE
MOUNTING
BAR (B)
MOUNTING
SCREWS (A)
KEY SLOTS (J)
FIXTURE
ARM (E)
COUPLING (M)
COVER
CAP (O)
NIPPLE (L)
GLASS
SHADE (P)
HEX NUT 3 (K3)
Line art shown may not exactly match the
fixture enclosed. However, the installation
instructions do apply to this fixture.
MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures
W-395
meet all UL specifications.
061814
1. Turn off power at circuit box to avoid possible electric shock.
2. Thread mounting screws (A) into mounting bar (B) (see fig. 1).
3. Secure mounting bar (B) to outlet box (C) with outlet box screws (D) (if applicable).
4. Spread fixture arms (E) to an equal distance apart.
5. Identify color coding of fixture wires (see fig. 2).
6. To connect wires, take black fixture wire (group A from fig. 2) and place evenly against black outlet
box wire. Do not twist wires.
7. Fit wire connector (F from figure 1) over wires and twist until there is a firm connection. If wire
connector (F) easily comes off, reattach and check again for a firm connection.
8. Repeat steps 5, 6 and 7 with the white (group B from fig. 2) fixture wires and outlet box wires.
9. Partially thread green grounding screw (G) into side hole (H) on mounting bar (B) (see fig. 1).
10. Wrap ground wire from fixture around green grounding screw (G) leaving enough excess wire,
then connect ground wire and outlet box wire with wire connector (F) (if applicable).
11. Tighten green grounding screw (G). Do not over tighten.
12. Tuck wires inside outlet box (C) (see fig. 1).
FIXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
1. Raise canopy (I) to ceiling allowing mounting screws (A) to protrude through key slots (J) in
canopy (I) and rotate canopy (I) clockwise until mounting screws (A) lock into narrow portion of
key slots (J), secure into place with mounting screws (A). (see fig. 1).
2. Thread hex nut 1 (K1) onto nipple (L) then thread nipple (L) into coupling (M) and secure hex nut 1
(K1).
3. Place nipple cover (N) over nipple (L) and secure with cover cap (O) and hex nut 2 (K2) or rubber
washer (if applicable).
4. Install lamps. Do not exceed recommended wattage.
5. Place fixture ring (Q) on top of glass shade (P), if applicable.
6. Raise glass shade (P) and fixture ring (Q), if applicable, so that nipple (L) protrudes through the
opening in glass shade (P) and secure with washer (R) and hex nut 3 (K3).
7. Place decorative cap (S) over nipple (L) and secure with finial (T).
8. Turn power back on at circuit box.
FIGURE 2.
FIXTURE
WIRES:
Black
WARNING
Turn off electricity to the mounting site before beginning installation.
Mounting instructions must be followed exactly as shown for the fixture to be safely sup-
BOX (C)
SIDE ported.
HOLE (H)
WIRE
CONNECTORS (F)
CLEANING AND CARE
OUTLET BOX
SCREWS (D)
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can
CANOPY (I) discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to
clean this fixture.
GREEN
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
GROUNDING
SCREW (G)
Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lac-
quer which gives maximum protection against the weather. However, in time the brightness of the
brass will tarnish, giving way to an authentic old-world brass finish. To keep your solid brass fixture
looking new for years to come, regularly apply a good quality, non-abrasive car wax to all metal sur-
faces, giving the fixture an extra protective covering.
HEX NUT 1 (K1)
ORDERING PARTS
NIPPLE
COVER (N) Keep this manual for future reference, and in case replacement parts are needed. Available parts can
be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
HEX NUT 2 (K2) or
RUBBER WASHER
FIXTURE
RING (Q)
WASHER (R)
DECORATIVE
CAP (S)
FINIAL (T)
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.
*NOT SUPPLIED
Used under license by Westinghouse Lighting.
FIXTURE FIXTURE
WIRES: WIRES:
White Bare
Copper
(Ground)
HOUSE HOUSE HOUSE
WIRES: WIRES: WIRES:
Black White Bare
(Hot) (Neutral) Copper
(Ground)
www.westinghouselighting.com
All rights reserved.
Guide d'utilisation
Appareil d' é clairage pour utilisation intérieure
GARANTIE LIMITÉE DE CINQ ANS
Cet appareil d'éclairage Westinghouse est assorti d'une garantie de 5 ans contre les défauts de matéri-
aux et de fabrication, qui entre en vigueur à partir de la date d'achat. La présente garantie se substitue
à toute autre garantie expresse ou tacite.
Cette garantie ne porte ni sur les dommages survenant suite à une catastrophe naturelle (telle que la
foudre), ni sur la corrosion ou la décoloration des pièces; la garantie ne porte pas sur les dommages
survenant suite à une utilisation anormale, une installation impropre, une surtension de courant élec-
trique ou des actes d'un tiers.
Cette garantie ne porte pas sur les frais de démontage et de réinstallation du ventilateur.
Si ce produit ne fonctionne pas, pour une raison quelconque couverte par cette garantie, contactez-
nous gratuitement au numéro suivant : 1-888-417-6222.
MISE EN GARDE:
L'ÉLECTROCUTION POURRAIT CAUSER DE GRAVES BLESSURES PERSONNELLES.
Lisez ces instructions et suivez-les exactement comme illustré. En cas de doute, ne commencez
pas l'installation. Consultez un électricien qualifié. Lisez toutes les instructions avant de com-
mencer l'installation. Un câblage approprié est essentiel au bon fonctionnement de cet appareil
d'éclairage. Lorsque vous faites une entaille ou que vous percez un trou dans un mur ou un
plafond, n'endommagez pas les câbles électriques, les canalisations de gaz ou d'eau. Si l'un des
composants de raccordement ou de l'appareil d'éclairage est endommagé, n'installez pas cet
appareil d'éclairage. Retournez-le à l'endroit où vous l'avez acheté.
Convient uniquement aux appareils comportant un avertissement indiquant que l'appareil
d'éclairage est doté d'un fil supportant une chaleur de 75°C ou 90°C. (Ces avertissements se
trouvent sur l'étiquette U.L. et sur l'emballage de l'appareil d'éclairage.)
NOTA: Pour appareil d'éclairage avec sortie terre. Cet appareil d'éclairage utilise un réceptacle
muni d'un fil de terre et ne doit pas être branché à un bloc d'alimentation à deux fils non mis à
la terre.
LES INSTRUCTIONS D'ASSEMBLAGE DE L'APPAREIL D'ÉCLAIRAGE POUR UTILISATION INTÉRIEURE
Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d'éclairage a été
conçu pour durer de nombreuses années. Si vous avez des questions ou des commentaires à
nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us.
NOTA : Déballez soigneusement l'appareil d'éclairage et les pièces. Assurez-vous que toutes les pièces
y sont avant de mettre l'emballage au rebut (voir fig. 1).
FIGURE 1.
BARRE DE
FIXATION (B)
VIS DE
FIXATION (A)
RAINURES (J)
BRAS L'APPAREIL
D'ECLAIRAGE (E)
ABAT-JOUR
EN VERRE (P)
L'ECROU
HEXAGONAL 3 (K3)
Il est possible que le dessin illustré ici ne
soit pas la reproduction exacte de l'appareil
d'éclairage contenu dans la boîte.
Les instructions d'installation demeurent
cependant valables.
Made in China
Instructions d'installation
FIL DE MISE
*BOITE DE SORTIE
A LA TERRE
DE COURANT (C)
TROU
LATERAL (H)
CONNECTEURS
DE FIL (F)
VIS DE LA BOITE DE
SORTIE DE COURANT (D)
CHAPEAU (I)
VIS DE MISE
A LA TERRE
(VERTE) (G)
L'ECROU
RACCORD (M) HEXAGONAL 1 (K1)
CACHE
MANCHON (N)
CACHE (O)
MANCHON
FILETE (L)
L'ECROU HEXAGONAL 2 (K2)
ou RONDELLE EN CAOUTCHOUC
ANNERO DE
L'APPAREL D'ECLAIRAGE (Q)
RONDELLE (R)
CAPUCHON
DECORATIF (S)
ECROU
DECORATIF (T)
*NON FOURNI