Table of Contents
Advertisement
Quick Links
To our customers,
Old Company Name in Catalogs and Other Documents
st
On April 1
, 2010, NEC Electronics Corporation merged with Renesas Technology
Corporation, and Renesas Electronics Corporation took over all the business of both
companies. Therefore, although the old company name remains in this document, it is a valid
Renesas Electronics document. We appreciate your understanding.
Renesas Electronics website:
Issued by: Renesas Electronics Corporation (http://www.renesas.com)
Send any inquiries to http://www.renesas.com/inquiry.
http://www.renesas.com
st
April 1
, 2010
Renesas Electronics Corporation
Advertisement
Table of Contents
Related Manuals for Renesas User System Interface Board HS1650ECN61H
Summary of Contents for Renesas User System Interface Board HS1650ECN61H
- Page 1 On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding.
- Page 2 Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific”...
- Page 3 H8SX/1650 Series E6000H TFP-120 User System Interface Board User’s Manual HS1650ECN61H Rev.3.0 2003.10...
- Page 4 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination.
-
Page 5: Important Information
Renesas) pursues a policy of continuing improvement in design, performance, functions, and safety of the user system interface board. Renesas reserves the right to change, wholly or partially, the specifications, design, user's manual, and other documentation at any time without notice. -
Page 6: Limited Warranty
User system interface boards are wearing parts which Renesas will not repair or replace if damaged and/or worn through use. The foregoing shall constitute the sole remedy for any breach of Renesas's warranty. - Page 7 This user's manual and user system interface board are copyrighted and all rights are reserved by Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any form, in hard-copy or machine-readable form, by any means available without Renesas's prior written consent.
-
Page 8: Read First
• READ this user's manual before using this user system interface board. • KEEP the user's manual handy for future reference. Do not attempt to use the user system interface board until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS This is the safety alert symbol. - Page 9 Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance.
- Page 10 Preface The HS1650ECN61H is a user system interface board that connects a user system for the H8SX/1650 Series TFP-120 package to the H8SX/1650 Series E6000H emulator (HS1650EPH60H).
-
Page 11: Table Of Contents
Section 1 Configuration...1 Section 2 Connection Procedures ...3 Connecting User System Interface Board to User System ... 3 2.1.1 Installing IC Socket... 3 2.1.2 Soldering IC Socket ... 3 2.1.3 Installing IC Socket... 4 2.1.4 Fastening IC Socket Connector... 4 Exchanging the Spacer of the EV-Chip Board ... -
Page 12: Section 1 Configuration
Figure 1 and table 1 show the configuration and components of the user system interface board for the TFP-120 package. Please make sure you have all of these components when unpacking. Screws (M2 8 mm) with flat washers Socket cover Figure 1 User System Interface Board for the H8SX/1650 Series TFP-120 Package Section 1 Configuration Spacer... - Page 13 Use an IC149-120-043-B51 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the TFP-120 package IC socket on the user system. Table 1 HS1650ECN61H Components No. Component Board IC socket Socket cover Screw (M2 x 12 mm) Screw (M2 x 8 mm) Spacers (2.6MP x 25 mm) 2 User’s manual CAUTION...
-
Page 14: Section 2 Connection Procedures
Section 2 Connection Procedures Connecting User System Interface Board to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. -
Page 15: Installing Ic Socket
2.1.3 Installing IC Socket Check the location of pin 1 before inserting. After checking the location of pin 1 on the user system interface board and pin 1 on the IC socket connector, align the guide pins on the IC socket connector with the guide holes on the user system interface board, and insert the IC socket connector into the IC socket (figure 2). - Page 16 User system Figure 2 Connecting User System Interface Board to User System Screws (M2 12 mm) with flat washers (for fastening cable head) Board Pin 1 IC socket (IC149-120-043-B51 manufactured by YAMAICHI ELECTRONICS Co., Ltd.)
-
Page 17: Exchanging The Spacer Of The Ev-Chip Board
Exchanging the Spacer of the EV-Chip Board While the user system interface board is connected to the user system, be careful not to apply load. Exchange the spacer (2.6MP mm) provided for the user system interface board. 10 mm) of the EV-chip board with another spacer (2.6MP EV-chip board Spacer (2.6MP... -
Page 18: Connecting User System Interface Board To Ev-Chip Board
Connecting User System Interface Board to EV-Chip Board Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. - Page 19 Figure 4 Connecting User System Interface Board to EV-Chip Board EV-chip board Connector No. Board EV-Chip Board Board Connector No. Connector No. UCN1 UCN1 UCN2 UCN2...
-
Page 20: Recommended Dimensions For User System Mount Pad (Footprint)
Recommended Dimensions for User System Mount Pad (Footprint) Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for a TFP-120 package (IC149-120-043-B51: manufactured by YAMAICHI ELECTRONICS Co., Ltd). Note that the dimensions in figure 5 are somewhat different from those of the actual chip's mount pad. -
Page 21: Dimensions For Ev-Chip Board And User System Interface Board
Dimensions for EV-Chip Board and User System Interface Board The dimensions for the EV-chip board and the user system interface board are shown in figure 6. 140.0 EV-chip board 118.5 102.5 16.0 78.5 Unit: mm Tolerance: ±0.5 mm User system interface board Figure 6 Dimensions for EV-Chip Board and User System Interface Board... -
Page 22: Resulting Dimensions After Connecting User System Interface Board
Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board to the user system, are shown in figure 7. SPACER ( 5.8) Figure 7 Resulting Dimensions after Connecting User System Interface Board EV-chip board IC socket (IC149-120-043-B51... -
Page 23: Section 3 Verifying Operation
Section 3 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8SX/1650 Series E6000H Emulator User's Manual (HS1650EPH60HE). 2. Verify the user system interface cable connections by checking the pin states with the CHECK command (emulator command) and checking the bus states with the FILL command (emulator command). - Page 24 To use the crystal oscillator mounted on the EV-chip board Install the crystal oscillator into the crystal oscillator terminals on the EV-chip board. Crystal oscillator terminals Figure 9 Installing the Clock Oscillator Enlarged view Crystal oscillator Evaluation chip board...
-
Page 25: Section 4 Notice
1. Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly aligned. 2. Do not apply excessive force to the user system interface board while it is connected to the user system. 3. The dimensions of the recommended mount pad for the IC socket for this user system interface board are different from those of the MCU. - Page 26 User System Interface Board User's Manual Publication Date: Rev.3.00, October 6, 2003 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd. 2003 Renesas Technology Corp. All rights reserved. Printed in Japan.
- Page 27 H8SX/1650 Series E6000H TFP-120 User System Interface Board User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ10B0048-0300H...