Download
Share
Print this page
Eden 8 Series Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. Eden Manuals
  4. Greenhouse Kit
  5. 8 Series
  6. Assembly instructions manual

Eden 8 Series Assembly Instructions Manual

Hide thumbs Also See for 8 Series:

Advertisement

Quick Links

Download this manual
New Zealand: 0508 333 654
Australia: 1800 316 654
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the 8 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Eden 8 Series

Summary of Contents for Eden 8 Series

  • Page 1 New Zealand: 0508 333 654 Australia: 1800 316 654...
  • Page 2 What you need to know: Front • Shade bracket (optional) • Triangle • Ridge • Head section • Slopes • Track support arm • Door track • Door brace • Door posts • Gussets • Threshold • Front brace • Base •...
  • Page 3 What you need to know: Back • Shade bracket (optional) • Triangle • Ridge • Mitre • Slope • Gusset • Centre vertical bar • Rear brace • Rear end brace • Vertical • Rear/side sill • Base...
  • Page 4 What you need to know: Middle Side glazing bars Gutter Side brace Side brace Base...
  • Page 5 Instructions overview: 1. Assemble 2 sides, back, front. 2. Put those four sides together. Keep braces and gussets finger-tight only at this point. 3. Attach the roof and ridge. 4. Attach the roof ventilator 5. Move the whole structure into final position 6.
  • Page 6 All 8 series DDHW have the same assembly procedures, variations are in the length of Ridge, gutter, and sills also the number of roof and side bars.
  • Page 7 Page: 6 & 7 Front & Rear views 9-11 Side Wall Assembly 12-15 Rear Wall 16-18 Front Wall 19 & 20 Extensions 21 & 22 Joining sections together 23 & 24 Attaching Ridge and Roof bars 25-27 Ventilator, assemble & attach 28 &...
  • Page 8 You are now embarking on your journey to build your Eden glasshouse! If the ride gets rough, don’t hesitate to contact us at sales@edenlite.co.nz. You will build the sides, back and front separately and then join them together afterwards. Please start by opening the box/s marked ‘middle’.
  • Page 9 The model shown here has the Eden Note: base kit attached. If you did not purchase this, secure your side sills to All bolts are standard 10mm size. a concrete or wooden sleeper. (see page 37 for base ideas) Do not fully tighten all bolts until the glasshouse has been glazed.

  • Page 10: Parts Needed

    Parts needed: • Gutter • Side glazing bar (1490mm) • Bracing angle (1598mm) • Side sills • Base • Nuts and bolts...
  • Page 11 Note: - Sill & Bases are riveted together View (c) shows the end of the base & sill with the slot, for attaching the front & rear...
  • Page 12 To assist with bringing the sections together, preload nuts & bolts 50mm approx. from each end on both front and rear walls X = Pre-load also To assist with bringing the sections together, preload a nut & bolts 50mm approx. from each end on both Front and rear walls, finger Insert two extra bolts on each bar as you assemble for the louvres, as well as three extras for the centre tight...
  • Page 13 View from outside of glasshouse...
  • Page 14 Parts needed: • Centre vertical bar • Verticals (1490mm) (2329mm) • 8’ gusset Slopes • (1490mm) • Nuts and bolts • Bracing angle (1563mm) • Side sills (2463mm) You will notice that the gussets, slopes, and verticals all have either blue, red, green, or yellow dots on them. These dots show what side of the glasshouse the verticals and slopes are •...
  • Page 15 Corner Bars: Note: The bolt track goes inside. The flat edge goes from the gusset to the sill/base. The lug (with the hole top and bottom) faces externally. Those holes are View from inside the glasshouse for joining extensions. Insert the extra bolts attach the Louvres, as well as top and bottom of corner bars, this will assist when...

  • Page 16: External View

    The corner bars, external lip with a hole top and bottom goes to the outside, this is only for joining extensions Preload Internal View External View...
  • Page 17 • 8’ gussets Parts needed: • Verticals • Front/door sill (1490mm) (2463mm) • Slopes • Base (fitted on door sill) (1490mm) • Door track • Threshold • Track support arm • Nuts and bolts (353mm) • 8’ triangle • Support bracket for door track •...
  • Page 18 Door with no Eden base or high sill. The door post goes as far as the sill sitting on the base. 3 screws are provided to attach the threshold to the door track and base.
  • Page 19 The holes for the Extension bracing are NOT predrilled, get the braces in place, clamp and drill IF on an Eden Base, attach the bottom of the brace to the anchor leg (This leg has an extra bracket attached). If NOT on the Eden Base move the brace up slightly and attach to...
  • Page 20 If adding to an existing glasshouse, remove the centre sill & base once the extension is attached This view is from inside looking at the ridge bar joining at the extension end, see how the ridge now sits on top of the corner section. Please Note: GLASS SIZING: where the extension joins onto the first frame, the glass...
  • Page 22 Preloaded Nuts and bolts, approximately 50mm in from the ends of the slope & vertical, finger tight prior to sliding the gutter in, also do the same at the bottom, place a nut on the bolt, just finger tight.
  • Page 23 Have preloaded nut and bolt, (50mm from top) finger tight prior to bringing ridge bar into the apex. On both slopes Note: Vents: decide where you want to place the vents, then preload All bolts are standard 10mm size. two extra nut & bolts on each roof bar where the vent will sit. Do not fully tighten all bolts until the If fitting Automatic openers, then only 1 nut &...
  • Page 24 Parts needed: • Ridge • Roof bars (1490mm) Attaching the Roof brace to the Top of the gutter Attaching the Roof brace to the Ridge Bar • Roof braces (1850mm)
  • Page 25 Attach the automatic vent opener once you have the vent in position in the roof...
  • Page 26 Vent top bar Parts needed: slots in here. • Vent hinge Hold the vent horizontal when slotting • Vent side bars it in the hole • Vent sill • Vent bottom bar • Ventomax opener...
  • Page 27 With Automatic Openers With Standard Quadrants Preloaded Nut & Bolts in Roof bars to attach Quadrants and Bottom bar...
  • Page 28 An Extra nut & bolt to be added where the Louvres are to be fitted, only the bottom is attached, the sides of the Louvre tuck in behind the bottom plate...
  • Page 29 If the bottom pane of glass has not been fitted, put the centre of the T at 612mm up from the sill. It is easier to fit the louvre with the bottom pane of glass in place as the cross bar can sit on the glass with the nuts loose but holding the T section in place (but not necessary).
  • Page 30 Space between panels is 645mm For Glasshouses with no Eden base or a high sill then only one panel to be fitted at the bottom. Panel spacing is 670mm apart...
  • Page 31 Parts needed • Door styles • Door handle • Door rollers • Door panels • Door head • Door guides • Rubber (for glazing) It is necessary to glaze the door before hanging it because it is more difficult to rubber it and insert the panes when it is already in place.
  • Page 33 End Caps: If the caps are loose, either place a piece of tape over the end of the bar or a little silicone to help hold in place.
  • Page 34 Anchoring the Glasshouse 1. The anchors should be on all four corners of the glasshouse. Longer models will have extra anchors which can be spaced out along the side. Please note that the holes in the base for the anchor posts are not factory drilled- you will need to drill your own where best fits.
  • Page 35 Glazing Rubber: Push into “outer track” using plastic spatula (supplied)..Glazing Clips: W type clip, the front edge overlaps the glass, 3mm Glass, trim back 40mm at the top of side and roof bars. 4mm Glass rebate back 50mm the back edge goes behind the glass.
  • Page 36 NOTE DOOR GLASS: is 635mm wide, same heights apply If no Eden base or high sill: 610mm x 685mm We recommend you start glazing from the bottom row of panes and work your way up to the top of the ridge.
  • Page 37 Model Dim A Dim B 88DDHW 2553 2546 810DDHW 2553 3163 812DDHW 2553 3780 814DDHW 2553 4432 816DDHW 2553 5039 818DDHW 2553 5656 820DDHW 2553 6273 822DDHW 2553 6890 824DDHW 2553 7507...
  • Page 38 Congratulations on completing your Eden glasshouse! We hope you enjoyed this project. Edenlite values your feedback and we would like to know if there is anything we can do to make this process of installing glasshouses easier for our customers. Feel free to contact us at: sales@edenlite.co.nz.

This manual is also suitable for:

8.12