Related Manuals for Rackmount RKP21x-208KVM Series
Summary of Contents for Rackmount RKP21x-208KVM Series
- Page 1 RKP21x-208KVM Series RKP241x-208KVM Series USER’S MANUAL WHERE TO BUY http://www.rackmountnet.com 1933 O'Toole Ave, #A107 San Jose, CA 95131, USA Toll Free Tel: (866)955-0598 email: sales@rackmountnet.com...
- Page 2 Introduction Thank you for purchasing RKP215-208KVM Rackmount LCD Keyboard Drawer with 8 ports KVM switch. LCD Keyboard Drawer with 8 ports KVM switch is ideal for application where space is critical. RKP215-208KVM is a combination of keyboard, trackball, KVM switch and TFT LCD packed into a drawer with features such as monitor flip up design, adjustable mounting brackets, built in LCD OSD, centralized control of 8 PCs.
-
Page 3: Packing Contents
Standard 3-in-1 KVM cable Before Unpacking It is very important to locate the LCD Keyboard Drawer with KVM switch in a suitable environment. The surface for placing and fixing the LCD Keyboard Drawer with KVM switch should be stable and level or mounted into a suitable cabinet. -
Page 4: Important Safeguards
Safe storage environment of the LCD Keyboard Drawer with KVM switch is ranging between –20 Permanent damage could occur if the LCD Keyboard Drawer with KVM switch is stored outside the safe range. Unplug the LCD Keyboard Drawer witch KVM switch immediately and call a qualified service personnel under the following conditions: The VGA signal cord is frayed or damaged. -
Page 5: Lcd Session
LCD Session Rev. JUL-02... -
Page 6: On-Screen Display (Osd)
OSD is the convenient way for a user to adjust the screen performance to his satisfaction. Menu / Selection Left 1. Entering the OSD Meun 2. Press the to display the OSD main menu. 3. Selecting icons for adjusting 4. Use buttons to scroll through the icons within the main menu and other sub-menus the currently selected icon will be highlighted. - Page 7 8. Select “Auto” for autoadjust LCD quality Rev. JUL-02...
-
Page 8: Customizing The Settings
Customizing the Settings 1. Brightness • To perform brightness adjustment of the input RGB signal 2. Contrast • To adjust the contrast level of the input signal 3. Phase • To optimize the picture quality by adjusting the sampling clock of the input RGB Signal 4. - Page 9 • To adjust the horizontal position of the OSD frame V - Position • To adjust the vertical position of the OSD frame Half Tone • To switch the OSD color from full color to half tone OSD Timeout • To modify the duration of the OSD time-out Information •...
-
Page 10: Resolution Setting
Half Tone • To switch LCD power ON/OFF auto mode Step 1 – Press right click on the desktop Step 3 – change the “Screen Resolution” Rev. JUL-02 Resolution Setting Step 2 – Choose “Properties” Step 4 – change the “Screen refresh rate”... - Page 11 My display doesn’t work, even though the computer appears to work 1. Make sure the power cable is securely plugged into the display Make sure the display is turned on 3. Try turning the display off and then turning it on again 4.
- Page 12 FAQ – Sun Server Sun Server are using resolution at 1152 x 900 x 76Hz Supported resolution mode 640 x 480 x 70/75Hz 800 x 600 x 70/75Hz 1024 x 768 x 70/75Hz 1280 x 1024 x 75Hz (17” LCD) Note the Max.
-
Page 13: Technical Information
4 Lamps Horizontal : 31-69 KHz Vertical : 56-75 Hz Analog RGB 0.7Vp-p VESA DPMS Micro on/off switch on the backside Brightness, Contrast, Color, H position, V position, Auto config, OSD adjust, Dither, etc. 12V/5A DC adapter 15-pin D-Sub connector 15”... -
Page 14: Kvm Session
KVM Session Rev. JUL-02... - Page 15 2. After Powering on computers and finishing the boot-up process, you can start to go KVM switch. Note: Please don’t switch the PC port (i.e. Don’t press the push button of KVM switch or run hot key) during the computers are under boot-up process. Rev. JUL-02...
- Page 16 1. Power on the KVM power 2. 7 segments LED is on 3. Key-in the password, default is “00000000” 4. If you forget your password, please send back to Manufacturer / Distributor 5. Pressing to view all port LED Indication When you change the channel If the PC is turn off or is disconnected The LED will flash otherwise is will lit...
-
Page 17: Hot Key
Press “Bank” & “Channel” at the same time to reset the KVM switch to default setting • S.L. + S.L. + • S.L. + S.L. + Note: You also could press “up arrow key” or “down arrow key” longer time to speed up selecting the destination port •... - Page 18 Rev. JUL-02...
- Page 19 / : SELECT PORT PgDn/PgUp: BANK SELECT Use “Tab” key to select items like Bank, OSD, SCAN, CHANGE PASSWORD, CONSOLE ON/OFF, etc… Use Page Up & Page Down to switch previous or next bank Rev. JUL-02 OSD Menu SYSTEM 02...
-
Page 20: Osd Menu
BANK : SYSTEM SYSTEM 03 SYSTEM 05 SYSTEM 07 OSD : SEC. CHANGE PASSWORD SCAN: SEC. CONSOLE ON/OFF ESC : QUIT ENTER :COMPLETE TAB : NEXT INSERT :EDIT / : SELECT PORT PgDn/PgUp: BANK SELECT Rev. JUL-02 OSD Menu • PC Name List •... -
Page 21: Osd - Password
ENTER PASSWORD : ESC : QUIT ENTER NEW PASSWORD : ESC : QUIT ENTER : COMPLETE RETYPE NEW PASSWORD : ESC : QUIT ENTER : COMPLETE NEW PASSWORD COMPLETE ESC : QUIT ENTER : COMPLETE Console On/OFF ON – any user can the console OFF –... - Page 22 Rev. JUL-02...
- Page 23 Using 3 in 1 KVM cable connect from Bank 1’s “Cascade port” to Bank 2’s “Console port”. After connected please press “Bank” & “Channel” button on the front of the KVM switch to reset the KVM switch. Bank 1 Bank 2...
- Page 24 4. Sun Server connection problem KVM switch are using standard PS/2 type keyboard and mouse and D-sub 15pin VGA for connection. If you need to connect Sun Server to KVM switch, you need a separate converter kit. Sun – 21 Kit Convert Sun Micro Din 8 pin Keyboard &...
- Page 25 Daisy Chain MAX Level 8 levels MAX PC Connection Housing Metal Power Adapter DC 12V 1A or DC 9V 1A Operation Temperature 0~40℃ Storage Temperature -20 ~ 60℃ Humidity 0~80%, Non-Condensing Size 19” Rack Mount / 1RU Rev. JUL-02 8 Ports KVM Switch...
Need help?
Do you have a question about the RKP21x-208KVM Series and is the answer not in the manual?
Questions and answers