Desa GM701U Assembly And Installation Instructions

Corner mantel kit

Advertisement

GM701U and GM700F
If this mantel is used with a heater equipped with a GA series heater blower accessory, use only a GHB802B
hearth base with this mantel. This will improve flame appearance and combustion.
If this mantel is used with a heater attached to a GHB802 or GHB802A hearth base, a heater blower accessory
should not be used.
IMPORTANT: Read entire instruction sheet before assembling or installing mantel kit.
This mantel is only approved for use with VMH2800T, VMH2800TA, CMH2800T, CMH2800TA, RF28T, or RF28TA Natural and Pro-
pane models. Do not use mantel with any other product. Heater must be attached to a GHB802 series hearth base accessory
before mantel installation. If heater does not have base accessory, contact dealer to purchase proper base.
This mantel kit contains the following pieces:
• Mantel right side
• Mantel left side
• Mantel front panel
• Two mounting strips
• Mantel top
• Corner left side
• Corner right side
• Two molding strips
• Gauge strip
• Hardware package
• L-Block
The hardware package contains the following:
• 2 - 2" screws
• 10 - 1 1/4" screws
• 6 finishing nails
Corner Mantel Kit
Assembly and
Installation Instructions
WARNING ICON
Finished
Unfinished
101433-04
101433-09
101433-01
101433-06
101433-03
101433-08
101016-01
101016-01
101433-02
101433-07
101789-01
101787-02
101788-01
101787-01
101433-05
101433-10
101015-01
101015-01
101052-01
101052-01
101216-01
101216-01
• 6 - 3" screws
• 4 wall anchors
CAUTION
G 001
Tools required:
• #2 Phillips screw driver (regular length)
• #2 Phillips screw driver (short length)
• Electric drill (if using wall anchors)
• 5/16" drill bit (if using wall anchors)
• Hammer
• Pencil
• Level
• Measuring Tape
• Hand or electric saw
If any of these pieces are missing or damaged, contact the dealer
where you purchased this kit or DESA International at 1-800-
972-7879.
Before installing mantel to heater, the heater must be mounted
on the GHB802, GHB802A, or GHB802B hearth base acces-
sory. Follow the steps below to assemble the mantel.
• 1/8" drill bit
• 1/16" drill bit

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GM701U and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Desa GM701U

  • Page 1 • Gauge strip If any of these pieces are missing or damaged, contact the dealer 101052-01 101052-01 • Hardware package where you purchased this kit or DESA International at 1-800- 101216-01 101216-01 • L-Block 972-7879. The hardware package contains the following: Before installing mantel to heater, the heater must be mounted •...
  • Page 2 Assembly and Installation Instructions (Continued) WARNING WARNING ICON G 001 Use care when finishing an unfinished mantel. Finish pieces before assembly. Do not finish mantel pieces near running heater or open flame. Vapors from finishing products are highly flammable. Follow manufacturer’s guidelines when using finishing products.
  • Page 3 Mounting Strip 15. Place heater in front opening of mantel. Slide mantel front panel into place to make sure heater is in correct position (see Figure 6). Follow instructions included with the base accessory to attach heater base to floor. 16.
  • Page 4 17. Center short side of heater mounting L-block on heater top and away from ignitor button and controls (see Figure 8). Make sure long side of L-block fits tight against mantel front panel. Do not cover any part of instruction decal. Find predrilled holes on short side of L-block.

This manual is also suitable for:

Gm700f

Table of Contents