Optional Accessory - DeWalt DCS353 Instruction Manual

English
Installing/Removing Accessories (Fig. E–G)
The tool features an exclusive Tool-Free System for faster
accessory changes and adjustments without the need for
wrenches or hex keys like other oscillating tool systems.
1. Grasp the tool and squeeze the Tool-Free accessory
clamp's lever.
3
2. Clean any residual debris from the tool shaft
the Tool-Free accessory clamp holder.
3. Slide the accessory between the shaft and the
accessory holder making sure the accessory
engages all of the pins
with the shaft.
4. Release the Tool-Free accessory clamp lever.
5. Some accessories, such as scrapers and blades can
be mounted at an angle if required.
Attaching Accessories Using the
Universal Adapter (Fig. I)

CAUTION: To avoid injury, do not use any accessory
for an application where the adaptor may fail to hold
the accessory.

CAUTION: Read and follow all manufacturers' safety
warnings for any accessories used with this tool.

CAUTION: To avoid injury, ensure adaptor and
accessory are securely tightened.
Non-D WALT accessories can be attached using the
e
universal adaptor.
1. Place the washer 21
2. Place accessory on to washer.
11
3. Tighten and secure adaptor nut
wrench 17 .
Attaching the Cut Guide (Fig. J)

Optional Accessory

The depth/cut guide allows you to precisely cut material at a
specified depth and more accurately track a marked cut line.
1. Attach the cut guide block
tabs 14 on the guide into the accessory side mount
slots 5 on the main body of the tool.
nOTE: The depth/cut guide can be attached to either
side of the tool.
2. Secure the block to the main body with the supplied
screw 27 and washer. Tighten with the supplied hex
wrench 17 .
Depth Guide (Fig. L)
Optional Accessory
This feature allows you to precisely cut material at a
specified depth.
1. Insert the guide arm 7
front slot on the guide block
2. Adjust the length of the guide by pulling out or pushing
inward to achieve the desired cut depth as shown in
Figure L.
3. Secure the guide in place by turning the depth/cut
adjustment knob 15
the depth/cut adjustment knob counterclockwise.
12
on the holder and is flush
12
on the tool.
19 using hex
by inserting the accessory
6
as shown in Figure L into the
6 .
clockwise. To release the guide turn
Cut Guide (Fig. K)
Optional Accessory
This feature allows you to more accurately track a marked
cut line.
1. Insert the guide arm
slots on the left and right sides of the guide block
13 and
2. Adjust the length of the guide by pulling out or pushing
inward to achieve the desired length as shown in
Figure K.
3. Secure the guide in place by turning the depth/cut
adjustment knob
the depth/cut adjustment knob counterclockwise.
nOTE: The guide arm can also be placed in the guard
assembly vertically in order to set the height off a cut. Refer
to Figure L.
Attaching the Dust Extraction Adaptor
(Fig. Q)
Optional Accessory
The Dust Extraction Adaptor allows you to connect
the tool to an external dust extractor, either using the
AirLock™ system (DWV9000-XJ), or a standard 35 mm dust
extractor fitment.
1. Attach the dust extraction adaptor
tabs 14
intake facing downward as shown in Fig. Q.
2. Insert screw
adaptor
wrench
17
Installing/Removing Sanding Sheets
(Fig. H)
Optional Accessory
A diamond shaped platen uses a hook and loop adhesion
system to attach the sanding sheets. The platen allows you
to use it on large flat surfaces and tight spots or corners.
1. Attach the sanding platen accesory as described under
Installing/Removing Accessories.
2. Align the edges on the sanding sheet with the edge
of the sanding platen and press the sanding sheet
onto the platen.
3. Firmly press the base with the sanding sheet
attached against a flat surface and briefly switch the
tool on. This provides for good adhesion between
the platen and the sanding sheet and also helps to
prevent premature wear.
nOTE: When the tip of the sanding sheet becomes
worn, detach the sheet from the platen, rotate
and reapply.
Belt Hook (Fig. P)
Optional Accessory

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
tool from a work belt. DO NOT use the belt hook
for tethering or securing the tool to a person or object
7 as shown in Figure K into the
15 clockwise. To release the guide turn
in to the accessory side mount slots
and washer into the dust extraction
27 28
and tighten with the supplied hex
18
.
6 .
18 by inserting the
5 with the