Table of Contents
Advertisement
Quick Links
AEOEZW062
Garage Door Controller
Firmware Version : 1.2
Quick Start
A To include the device turn the primary controller of Z-Wave network into inclusion mode,
short press the product's Z-Wave button that you can find on the product's housing.
Please refer to the chapters below for detailed information about all aspects of the products
usage.
What is Z-Wave?
This device is equipped with wireless communication complying to the Z-Wave standard. Z-
Wave is the international standard for wireless communication in smart homes and
buildings. It is using the frequency of 868.42 MHz to realize a very stable and secure
communication. Each message is reconfirmed (two-way communication) and every mains
powered node can act as a repeater for other nodes (meshed network) in case the receiver is
not in direct wireless range of the transmitter.
Z-Wave differentiates between Controllers and Slaves. Slaves are either sensors (S)
transmitting metered or measured data or actuators (A) capable to execute an action.
Controllers are either static mains powered controllers (C) also referred to as gateways or
mobile battery operated remote controls (R). This results in a number of possible
communication patterns within a Z-Wave network that are partly or completely supported by
a specific device.
1. Controllers control actuators
2. Actuators report change of status back to
controller
3. Sensors report change of status of measured values to controller
4. Sensors directly control actuators
5. Actuators control other actuators
6. Remote controls send signals to static controllers to trigger scenes or other actions
7. Remote controls control other actuators.
There are two different role a controller can have. There is always one single primary controller that is managing
the network and including/excluding devices. The controller may have other functions - like control buttons - as
Advertisement
Table of Contents
Related Manuals for Aeon Labs AEOEZW062
Summary of Contents for Aeon Labs AEOEZW062
- Page 1 AEOEZW062 Garage Door Controller Firmware Version : 1.2 Quick Start A To include the device turn the primary controller of Z-Wave network into inclusion mode, short press the product’s Z-Wave button that you can find on the product's housing. Please refer to the chapters below for detailed information about all aspects of the products usage.
-
Page 2: Product Description
Sensors only communicate with static controllers. Product description Aeon Labs Garage Door Controller is a smart and wireless Garage Door Control system, you can control the garage door to open, close, or stop moving via wireless signal on your gateway client or phone application. - Page 3 Installation Guidelines The Garage Door Controller must be installed in your home and near the garage door. It cannot be installed outdoors in elements such as rain and snow. 1. Utilize the provided 20mm screws to affix it to the desired surface. 2.
- Page 4 Installing the Sensor on your garage door. Affix your sensor mounting plate to the garage door. The sensor mount plate should be installed on the top of the garage door (on the left, middle, or right side). Now affix your sensor mounting plate to the surface.
-
Page 5: Behavior Within The Z-Wave Network
Behavior within the Z-Wave network I On factory default the device does not belong to any Z-Wave network. The device needs to join an existing wireless network to communicate with the devices of this network. This process is called Inclusion. Devices can also leave a network. This process is called Exclusion. - Page 6 1. Unlock the Back Mount Plate of Garage Door Controller by twisting the Back Mount Plate and separating the two parts of your Garage Door Controller. 2. Power your Garage Door Controller by connecting the 5V DC Adapter to the input. 3.
-
Page 7: Configuration Parameters
A Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. - Page 8 Value Description Get the number of alarm music. (Default) Alarm Mode When Opening (Parameter Number 37, Parameter Size 4) Configure the alarm mode for when the garage door is opening. Value1: configure the frequency of blinking for the Alarm LED, there are 10 levels that 1 to10 level, the minimum frequency is level 1 and the max frequency is level 10.
- Page 9 Select an alarm sound, there are 4 alarm sounds in the flash memory card can 256 — 356 be selected. 65535 — Configure the volume of alarm sound, there are 10 levels can be set. 65545 16777215 Disable the alarm mode. 16777216 Enable the alarm mode.
-
Page 10: Command Classes
Function of Button- or Button+ (Parameter Number 47, Parameter Size 1) Define the function of Button- and Button+. Value Description Pressing it once, the Button+ and Button- are defined to be used to increase and decrease the volume. Press and hold it, the Button+ and Button- are defined to be the control item of Next and Previous. -
Page 11: Technical Data
• Manufacturer Specific (version 2) • Powerlevel (version 1) • Firmware Update Meta Data (version 2) • Association (version 2) • Version (version 2) • Security (version 1) • Device Reset Locally (version 1) • Hail (version 1) Controlled Command Classes •... - Page 12 Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well- being.
Need help?
Do you have a question about the AEOEZW062 and is the answer not in the manual?
Questions and answers