Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Aeon Labs Manuals
  4. Controller
  5. Nano Shutter
  6. User manual

Aeon Labs Nano Shutter User Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Nano Shutter user guide.
Modified on: Mon, 6 May, 2019 at 8:38 PM
Aeotec Nano Shutter.
Aeotec Nano Shutter
(https://aeotec.com/z-wave-motor-shutter-curtain-control)
sockets and switches using Z-Wave Plus
(http://aeotec.com/z-wave-gen5)
To see whether Nano Shutter is known to be compatible with your Z-Wave system or not, please reference our Z-Wave
gateway comparison
(http://aeotec.com/z-wave-gateways)
(https://aeotec.freshdesk.com/solution/articles/6000198818-nano-shutter-technical-specifications-)
Familiarize yourself with your Nano Shutter.
Important safety information.
(http://aeotec.com/z-wave-plus)
technology.
has been crafted to power connected
. It is powered by Aeotec's Gen5
listing. The technical specifications of Nano Shutter
can be viewed at that link.

Advertisement

loading
Need help?

Need help?

Do you have a question about the Nano Shutter and is the answer not in the manual?

Questions and answers

Related Manuals for Aeon Labs Nano Shutter

Summary of Contents for Aeon Labs Nano Shutter

  • Page 1 . It is powered by Aeotec’s Gen5 (http://aeotec.com/z-wave-plus) technology. (http://aeotec.com/z-wave-gen5) To see whether Nano Shutter is known to be compatible with your Z-Wave system or not, please reference our Z-Wave gateway comparison listing. The technical specifications of Nano Shutter (http://aeotec.com/z-wave-gateways) can be viewed at that link.
  • Page 2 Keep product away from open flames and extreme heat. Avoid direct sun light or heat exposure. Nano Shutter is intended for indoor use in dry locations only. Do not use in damp, moist, and / or wet locations. Install the Nano Shutter.
  • Page 3 Note: All connection wires needs to be a flexible cable. 120-230VAC Wiring diagram of Nano Shutter. N – Power input for neutral. L – Power input for live.. IN – Input for load power supply. OUT1 – Output for Motor direction 1.
  • Page 4 S2 – External switch 2 control for Motor. (use -24VDC) 3. Install Nano Shutter to the gang box. a. Live/Hot wire connection: Connect the Live/Hot wire to the “L” terminal on the Nano Shutter. + Live/Hot on External Switch input.
  • Page 5 1. Mounting the gang box. 2. Position all wires to provide room for the device. Place the Nano Shutter inside the gang box towards the back of the box. 3. Position the antenna towards the back of the box, away from all other wiring.

  • Page 6: Advanced Functions

    Nano Shutter is entering into pairing mode. 3. If the Nano Shutter has been successfully added to your Z-Wave network, its RGB LED will be solid. If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient. Repeat the instructions above from step 1.
  • Page 7 To automatically detect and set the mode to the appropriate type of manual switch wired into Nano Shutter, toggle the button on the manual switch once and wait 2 seconds for the Nano Shutter to detect the type of manual switch.
  • Page 8 Instant updates. By default Nano Shutter is not set to report its status automatically. If you need to have your Nano Shutter report to your gateway any time its status has been changed, you can do so using the configuration settings below:...

  • Page 9: Touch Panel Control

    To do this, press and hold the Action Button for 20 seconds and then release it. Your Nano Shutter will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.