Advertisement
The 5000CM is a wireless magnetic contact detecting the opening of doors, tilting doors and
windows. To take best advantage of the protective effect of the 5000CM we recommend
positioning it as follows:
- On one-wing doors and windows, install the magnetic contact on the side opposite to the hinge
- On double-wing doors and windows, install the magnetic contact on the wing fitted with the
handle, on the side opposite to the hinge.
Programming
To link up the sensor to the control unit, remove the cover and select the dip switches (from No.
1 to No. 8) located in the printed circuit.
CAUTION : each wireless peripheral must have a unique code, different from those of all the
other peripherals (see table at the end of the User Manual for possible double codes).
Access the control unit programming function by following the instructions provided in the
installation manual (par. 3.1) and go to the "PROGRAM SENSORS?" menu (par. 3.4). Assign
a code to the sensor.
The 5000CM is a wireless magnetic contact detecting the opening of doors, tilting doors and
windows. To take best advantage of the protective effect of the 5000CM we recommend
positioning it as follows:
- On one-wing doors and windows, install the magnetic contact on the side opposite to the hinge
- On double-wing doors and windows, install the magnetic contact on the wing fitted with the
handle, on the side opposite to the hinge.
Programming
To link up the sensor to the control unit, remove the cover and select the dip switches (from No.
1 to No. 8) located in the printed circuit.
CAUTION : each wireless peripheral must have a unique code, different from those of all the
other peripherals (see table at the end of the User Manual for possible double codes).
Access the control unit programming function by following the instructions provided in the
installation manual (par. 3.1) and go to the "PROGRAM SENSORS?" menu (par. 3.4). Assign
a code to the sensor.
RF Test
Having assigned a code to the sensor, we recommend that you perform the RF test to verify
the presence of radio communications between the sensor and the control unit.
For the RF test, position dip switch no. 9 on "ON". This will cause the cyclic emission of an
RF signal which is detected by the alarm system and visualised on the display when you
enter the "SYSTEM TEST" function (par. 3.10). At the end of the test, it is important to reset
ANTI-SABOTAGE
dip switch no. 9 on "OFF" (normal operating mode).
BUTTON
Operating test
DIP-SWITCH
After fastening the 5000CM to the door or window make sure that the opening of the door or
window causes the LED DL1 to flash three times. This tells you that the alarm signal is being
LED DL 1
transmitted and hence that the sensor is working properly. If this is not so, make sure that the
LED DL 2
distance between the reed and the magnet does not exceed the distance necessary for the
attraction of the reed. The 5000CM sends out a single transmission, even if the cause of alarm
persists. When the cause of alarm is discontinued, the 5000CM gets ready to operate again.
TERMINAL STREEP
The anti-sabotage function also works in this manner.
Checking and replacing the battery
When battery voltage drops below 6 V, the sensor indicates this condition by giving out a
visual signal (LED DL2 lights up) each time the contact is opened.
This transmits a battery low signal which is acquired by the control unit in the zone where the
device has been memorised. The dedicated output (terminal 22) is also activated for 30
seconds.
RF Test
Having assigned a code to the sensor, we recommend that you perform the RF test to verify
the presence of radio communications between the sensor and the control unit.
For the RF test, position dip switch no. 9 on "ON". This will cause the cyclic emission of an
RF signal which is detected by the alarm system and visualised on the display when you
enter the "SYSTEM TEST" function (par. 3.10). At the end of the test, it is important to reset
dip switch no. 9 on "OFF" (normal operating mode).
ANTI-SABOTAGE
BUTTON
Operating test
DIP-SWITCH
After fastening the 5000CM to the door or window make sure that the opening of the door or
window causes the LED DL1 to flash three times. This tells you that the alarm signal is being
LED DL 1
transmitted and hence that the sensor is working properly. If this is not so, make sure that the
LED DL 2
distance between the reed and the magnet does not exceed the distance necessary for the
attraction of the reed. The 5000CM sends out a single transmission, even if the cause of alarm
persists. When the cause of alarm is discontinued, the 5000CM gets ready to operate again.
TERMINAL STREEP
The anti-sabotage function also works in this manner.
Checking and replacing the battery
When battery voltage drops below 6 V, the sensor indicates this condition by giving out a
visual signal (LED DL2 lights up) each time the contact is opened.
This transmits a battery low signal which is acquired by the control unit in the zone where the
device has been memorised. The dedicated output (terminal 22) is also activated for 30
seconds.
Advertisement
