Subscribe to Our Youtube Channel
Related Manuals for Meinberg GNSS Multiband Antenna
Summary of Contents for Meinberg GNSS Multiband Antenna
- Page 1 MANUAL GNSS MULTI BAND Antenna Antenna / Converter Unit May 11, 2022 Meinberg Funkuhren GmbH & Co. KG...
-
Page 3: Table Of Contents
........4 Installation of the GNSS Multiband Antenna 5 Technical Specifications GNSS Multiband Antenna... -
Page 4: Imprint
1 Imprint 1 Imprint Meinberg Funkuhren GmbH & Co. KG Lange Wand 9, 31812 Bad Pyrmont, Germany Phone: + 49 (0) 52 81 / 93 09 - 0 Fax: + 49 (0) 52 81 / 93 09 - 230 Website: https://www.meinbergglobal.com Email: info@meinberg.de... -
Page 5: Safety Hints Antenna
2 Safety Hints Antenna WARNING! DANGER TO LIFE BY ELECTRICAL SHOCK! Make sure to comply with the occupational health and safety standards when installing the antenna. Never work without a proper fall protection device! Do not carry out any installation or maintenance work on the antenna system or cabling when there is a potential risk of lightning. -
Page 6: Before You Start
Carefully unpack the system and all accessories and put them aside. Check the scope of delivery with the pack- ing list to ensure that no parts are missing. If any of the listed contents are missing, please contact Meinberg Funkuhren. -
Page 7: Disposal Of Packaging Materials
3.2 Disposal of Packaging Materials The packaging materials we use are fully recyclable: Material Use for Disposal ———————————————————————————————————————— Polystyrol packaging frame/filling material Recycling Depot (polystyrene peanuts, bubble wrap) PE-LD accessories packaging Recycling Depot Polyethylene low density Cardboard shipping packaging, Paper recycling accessories packaging ————————————————————————————————————————... -
Page 8: Installation Of The Gnss Multiband Antenna
4 Installation of the GNSS Multiband Antenna 4 Installation of the GNSS Multiband Antenna WARNING! Do not mount the antenna without an effective fall arrester! Danger of death from falling! - Ensure that you work safely when installing antennas! - Never work without an effective fall arrester! - Page 9 Case Example 4: If the cable leading from the point of entry into the building to the Meinberg system is laid together with other cables (for example in a cable duct alongside high-voltage cables), transient voltages may "leak" into the antenna cable, causing damage to your system.
- Page 10 4 Installation of the GNSS Multiband Antenna Mounting the Antenna Use the included mounting kit to mount the antenna at a distance of 50 cm from other antennas, either on Clear view of the sky! a vertical pole of a diameter of no more than 60 mm, or directly onto a wall.
- Page 11 Grounding Conductor To ground the antenna cable, connect the surge protec- to Grounding Busbar tor to a grounding busbar using a grounding conductor Conductor of diameter approx. 1.5 mm (see illustration). attached to surge protector As short as possible Once installation is complete, connect the other end of the antenna cable to the surge protector female con- nector.
- Page 12 4 Installation of the GNSS Multiband Antenna Optional Antenna Splitter Multiple receivers can be connected to one antenna using the antenna splitter. When doing so, be aware that the total distance, comprising the cable from the antenna to the splitter, and from there to the receiver, must not exceed the maximum cable length.
- Page 13 Cable Delay Usage RG 58U 5 ns/m For GPS and GNS-UC receivers H-155 4 ns/m For GNS and GNM receivers The cable length entered (from antenna to receiver) is used by the system to calculate the delay time and to automatically compensate for propagation delay. A value of 20 m is set by default. When using a different type of coaxial cable, please use the "By Delay"...
-
Page 14: Technical Specifications Gnss Multiband Antenna
5 Technical Specifications GNSS Multiband Antenna 5 Technical Specifications GNSS Multiband Antenna Physical Dimensions: GNSS MULTI BAND Antenna Date: May 11, 2022... - Page 15 Specifications: Power supply: 5 V - 16 V, 24 mA (via antenna cable) Antenna- input GNSS: Antenna circuit insulated, dielectric strenght 1000V Frequency ranges: 1164 MHz to 1254 MHz and 1525 MHz to 1606 MHz Overall LNA gain: 37 dB typ, 35 dB min LNA noise figure: 2.5 dB typ at 25 C Supported frequency bands:...
-
Page 16: Technical Specifications: Mbg S-Pro Surge Protection
5 Technical Specifications GNSS Multiband Antenna 5.1 Technical Specifications: MBG S-PRO Surge Protection Adapter plug with replaceable gas discharge tube for coaxial signal connections. Connector Type: Type-N connector female/female. The MBG S-PRO set includes a surge protector (Phoenix CN-UB-280DC-BB), a pre-assembled coaxial cable, and a mounting bracket. - Page 17 Max. Discharge Current: (8/20) s Maximum (Core-Shield) 20 kA Rated Pulse Current: (10/1000) s (Core-Shield) 100 A Impulse Discharge Current: (10/350) s, Peak Value I 2.5 kA Output Voltage Limit: At 1 kV/ s (Core-Earth) spike 900 V At 1 kV/ s (Core-Earth) spike 900 V Response Time: tA (Core-Earth)
-
Page 18: Mbg S-Pro: Physical Dimensions
5 Technical Specifications GNSS Multiband Antenna 5.1.1 MBG S-PRO: Physical Dimensions 15,8 5.1.2 Installation and Grounding GNSS MULTI BAND Antenna Date: May 11, 2022... -
Page 19: Rohs And Weee
WEEE-compliant fashion, it must be returned to the manufacturer. Any transportation ex- penses for returning this product (at end-of-life) must be covered by the end user, while Meinberg will bear the costs for the waste disposal itself. Date: May 11, 2022... -
Page 20: Declaration Of Conformity
7 Declaration of Conformity 7 Declaration of Conformity Konformitätserklärung Doc ID: GNSS Multiband Antenna-May 11, 2022 Hersteller Meinberg Funkuhren GmbH & Co. KG Manufacturer Lange Wand 9, D-31812 Bad Pyrmont erklärt in alleiniger Verantwortung, dass das Produkt, declares under its sole responsibility, that the product...
Need help?
Do you have a question about the GNSS Multiband Antenna and is the answer not in the manual?
Questions and answers