Subscribe to Our Youtube Channel
Related Manuals for Meinberg GOAL
Summary of Contents for Meinberg GOAL
- Page 1 MANUAL GOAL GPS Optical Antenna Link 3rd November 2020 Meinberg Funkuhren GmbH & Co. KG...
-
Page 3: Table Of Contents
2.11 Return of Electrical and Electronic Equipment ......3 Features of GOAL 4 Installation 5 Technical Specifications... -
Page 4: Imprint
1 Imprint 1 Imprint Meinberg Funkuhren GmbH & Co. KG Lange Wand 9, 31812 Bad Pyrmont / Germany Phone: + 49 (0) 52 81 / 93 09 - 0 Fax: + 49 (0) 52 81 / 93 09 - 230 Internet: https://www.meinbergglobal.com... -
Page 5: Important Safety Information
Meinberg Funkuhren shall not be responsible for any damage arising due to non-observance of these regulations. -
Page 6: Used Symbols
Dieses Produkt fällt unter die B2B Kategorie. Zur Entsorgung muss es an den Hersteller übergeben werden. This product is handled as a B2B category product. In order to secure a WEEE compliant waste disposal it has to be returned to the manufacturer. GOAL Date: 3rd November 2020... - Page 7 This manual is intended exclusively for electricians or persons trained by an electrician who are familiar with the applicable national standards and safety rules. Installation, commissioning and operation of this device may only be carried out by qualified personnel. Date: 3rd November 2020 GOAL...
-
Page 8: Security During Installation
For safety reasons, the device with the highest mass should be installed in the lowest position of the rack. Other devices must be placed from the bottom to the top. The device must be protected against mechanical stress such as vibration or shock. GOAL Date: 3rd November 2020... - Page 9 fluids or foreign objects enter), the current flow can be interrupted. Questions about the house installation, need to be clarified with your house administration. The power supply should be connected with a short, low-inductance line. Date: 3rd November 2020 GOAL...
- Page 10 GOAL Date: 3rd November 2020...
-
Page 11: Protective Conductor- / Ground-Terminal
If an external earth connection is provided on the housing, it must be connected to the equipotential bonding rail (grounding rail). The mounting parts (without cable) are not included in the scope of delivery. Note: Please use a grounding cable 1.5 mm Always pay attention to a correct crimp connection! Date: 3rd November 2020 GOAL... -
Page 12: Fuse Replacement
Voltage Current Voltage with or without extinguishing agent with extinguishing agent T = Time-lag / SB = SlowBlow T = Time-lag / SB = SlowBlow Dimensions: Dimensions: 5 x 20 mm 5 x 20 mm GOAL Date: 3rd November 2020... -
Page 13: Fiber Optic
Devices that are connected via one or more uninterruptible power supplies (UPS) remain operational even when the UPS power cord is disconnected. Therefore, you must put the UPS out of operation according to the documentation of the corresponding user documentation. Date: 3rd November 2020 GOAL... -
Page 14: Safety During Maintenance
Liquid can destroy the electronics of the device! Liquid penetrates into the housing of the device and can cause a short circuit of the electronics. Only clean with a soft, dry cloth. Never use solvents or cleaners. GOAL Date: 3rd November 2020... -
Page 15: Prevention Of Esd Damage
ESD protective covers, which are extremely wrinkled or even have holes, no longer protect against electrostatic discharge. ESD protective covers must not be low-resistance and metallically conductive if a lithium battery is installed on the assembly. Date: 3rd November 2020 GOAL... -
Page 16: Return Of Electrical And Electronic Equipment
Return and Collection Systems For returning your old equipment, please use the country-specific return and collection systems available to you or contact Meinberg. The withdrawal may be refused in the case of waste equipment which presents a risk to human health or safety due to contamination during use. -
Page 17: Features Of Goal
- no unintentional monitoring via optical fiber The receiver-side module GOAL/R is supplied with power via the antenna input connector of the GPS re- ceiver, therefore no external power supply is necessary. The module GOAL/A needs an external supply for operating and feeding the GPS antenna. -
Page 18: Installation
(A+B) and the optical fiber (C). The receiver is able to correct this delay if the exact total cable length (A + B + C) is given. When GOAL is used, a value of 20 mtrs should be added to the total cable lenght in order to compensate the fixed delay caused by the GOAL system. -
Page 19: Technical Specifications
Do not clean the components with unsuitable methods or instruments but use the enclosed dust covers while no FO cable is connected, e.g. during transport. Disregarding this notes may cause permanent dam- age of the device! Date: 3rd November 2020 GOAL... -
Page 20: Goal/A
Optical budget: 10 dB (50/125 m) Status LEDs: Antenna: green: ok red: not connected or short circuit FO Link: green: ok red: no sufficient interconnection to the GOAL/R Connectors: ST connector (FO Link) female type-N (Antenna) power supply via 5pin DFK connector Power Requirements:... -
Page 21: Goal/R
Humidity: 85% max. Housing: Aluminium HF housing, IP30 protected Physical Dimensions: 25 mm x 25 mm x 95 mm (height x width x depth) CLASS 1 LED PRODUCT Site View, Front and Rear View GOAL/R Date: 3rd November 2020 GOAL... -
Page 22: Rohs And Weee
Any transportation expenses for return- ing this product (at its end of life) have to be incurred by the end user, whereas Meinberg will bear the costs for the waste disposal itself. GOAL... -
Page 23: Eu Declaration Of Conformity
7 EU Declaration of Conformity Konformitätserklärung Doc ID: GOAL - GPS Optical Antenna Link-2020-11-03 Hersteller Meinberg Funkuhren GmbH & Co. KG Manufacturer Lange Wand 9, D-31812 Bad Pyrmont erklärt in alleiniger Verantwortung, dass das Produkt, declares under its sole responsibility, that the product...
Need help?
Do you have a question about the GOAL and is the answer not in the manual?
Questions and answers