System Connections - Onkyo DX-C370 Instruction Manual

Compact disc changer
Table of Contents

Advertisement

System Connections

Do not plug in the power cord until all connections have been made.
On each pair of input or output jacks, the jack marked R corresponds to the right channel and the jack marked L corresponds to the left
channel.
L
R
ANALOG
OUTPUT
Audio
connection cable
L
R
CD
Amplifier
Connecting to an audio system
Two types of output jacks are located on the rear panel.
Use the DIGITAL OUTPUT jack if you are connecting the unit to
audio equipment that supports a digital connection.
ANALOG OUTPUT jacks:
These are the most commonly used jacks. Connect these jacks to the
amplifier's CD input jacks using the supplied audio connection cable.
DIGITAL OUTPUT (optical output) jack:
For digital recording, connect this jack to the digital input jack of a
Mini Disc recorder, a DAT deck, or other digital equipment. If your
amplifier has a digital input jack, connecting the DIGITAL OUT-
PUT jack to it will produce a much clearer and more dynamic sound.
Terminal protection cap is attached to the digital jack.
Remove the cap when connecting the unit to other digital equip-
ment. When you are not using the digital output jack, replace the
cap.
Refer to the amplifier's instruction manual for connections.
1 1
NEXT SELECTION
OPEN/CLOSE
POWER
DISPLAY
MEMORY CLEAR
DISC SKIP
ON
OFF
6 DISC
FIVE CD EXCHANGE CONTINUOUS PLAY
WARNING
AVIS
RISK OF ELECTRIC SHOCK
RISQUE DE CHOC ELECTRIQUE
DO NOT OPEN
NE PAS OUVRIR
OPTICAL
REMOTE
DIGITAL
CONTROL
OUTPUT
cable
Optical fiber cable
(not included)
Optical IN
DAT, MD recorder or
Digital amplifier
PAUSE
STOP
PLAY
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
DISC 6
To AC outlet
COMPACT DISC CHANGER
DX-C540
®
COMPACT DISC PLAYER
"CLASS 1 LASER
DX - C370
MODEL NO.
PRODUCT"
RATING AC120V/220-230V
50/60Hz
10W
2-1, NISSHIN-CHO, NEYAGAWA-SHI, OSAKA,
JAPAN
MANUFACTURED IN MALAYSIA
Connections for remote controller (
When connecting Onkyo products, it is necessary to attach the
cable to be able to use the remote controller of the main component
to control the entire system.
1. To use this CD changer with an amplifier (or receiver), cassette
tape deck, and tuner that include the appropriate
nect the components using the
MOTE CONTROL jacks.
2. As the exact connection sequence of the
tant, you can connect from the amplifier (or receiver) to either the
tuner, cassette tape deck, or compact disc changer.
3. To operate correctly, the remote controller must point toward the
remote control sensor of the amplifier (or receiver).
NOTES:
The upper and lower
same function.
Remote controller operation is not possible when only the
cable is connected – the audio connection cables must also be
connected.
An
cable equipped with a 3.5mm (1/8 in.) diameter minia-
ture two-conductor phone plug is included with this unit and with
every tuner and cassette tape deck that utilizes the
2 2
POWER
ON
OFF
VOLTAGE SELECTOR
120V
220-230V
Voltage selector
(worldwide model only)
(See page 5)
cable, plugged into the RE-
cable is unimpor-
REMOTE CONTROL jacks have the
Connecting the power
Before plugging in the unit, confirm that all
connections have been made properly.
1 . 1 .
Insert the AC power supply cord into
the outlet.
2 . 2 .
Press the POWER button.
When the power first turns on, the carou-
sel rotates to find a disc and stops auto-
matically if there is a disc on the disc tray.
To wall
outlet
)
jack, con-
jack.
7

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents