Subscribe to Our Youtube Channel
Related Manuals for Laser Technology CR40C
Summary of Contents for Laser Technology CR40C
- Page 1 南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD CR40C Laser Operator’s Manual...
-
Page 2: Table Of Contents
The back panel Description…………………………………………………………………………….8,9 Series CR Parameters and Installation diagram CR Series laser parameter table………………………………………………………………………..10 CR40C Installation diagram……………………………………………………………………….…..10 Figure 1：The panel Description…………………………………………………………………….….11 Figure 2：CR40C Outline diagram……………………………………………………………… …… 12 Figure 3：CR40C Mounting hole…………………………………………………………………….…13 CRD Laser after-sales service commitment CRD Laser after-sales service commitment………………………………………………………... 14,15... -
Page 3: Dangerous Warning
南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD Laser Safety Dangerous Warning: Danger: Imminent hazards which, if not avoided, will result in death or serious injury. Warning: Potential hazards which, if not avoided, could result in death or serious injury. Caution: Potential hazards or unsafe practices which, if not avoided, may result in minor or moderate injury. -
Page 4: Safety Regulations
◆ Class 4 laser product, Invisible laser radiation, Avoid eye or skin exposure to direct or scattered radiation ◆ Laser Radiation Warning. ◆ Laser label. Model: CR40C; Serial Number: 309001；Production date: January 4th,2009 ◆ Anti-action label removed, damage cannot be maintained. -
Page 5: Getting Started
南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD Getting Started Inspection the packaging: 1. Inspect all shipping containers for signs of damage, severe deformation and damp. 2. Inspect the integrity of the sealing tape. 3. Inspect the position of Laser in the box is correct after the unpacking (loose in the package of plastic bubble). -
Page 6: Operation
Choice and connection of Power: ◆ DC switching power chose by customer will be matched to the requirements CR40C lasers, Voltage is 48V, current should be not less than 12.5A. ◆ The diameter of connecting wire between DC power supplier and laser tube should be larger than 2.5mm... - Page 7 南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD ◆ The external control signals of CR40C Laser are accessed through the back panel BNC connector of the laser. Pulse width modulation (PWM): CR40C Laser is controlled laser power by Pulse width modulation (PWM). The low voltage range should be 0 to 0.5V (laser off), the high voltage, ranges should be...
-
Page 8: The Back Panel Description
南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD The back panel Description: The panel including (see Installation Figure 1): ● Power input terminals ● Switch ●Power indicator light(green light) ● Laser indicator light(green red) ●BNC connector(signal input) Specific steps are as follows: 1. -
Page 9: Series Cr Parameters And Installation Diagram
南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD Series CR Lasers Parameters and Installation diagram 1. Series CR Lasers Parameters CR40C CR40Ch CR40Ci Model 10.6 10.2 Wavelength μ μ μ >45W >40W >30W Power <±5％ Power Stability <1.2 Model Quality 2±0.2mm Beam Waist Size <7mrad... -
Page 10: Crd Laser After-Sales Service Commitment
NANJING CRD LASER TECHNOLOGY CO., LTD CRD Laser after-sales service commitment Dear customers: Thank you for purchasing series CR lasers from Nanjing CRD Laser Technology Co., LTD., in order to relieve your worries; we will make our warranted services for you, as the following commitments: 1. - Page 11 南京晨锐腾晶激光科技有限公司 NANJING CRD LASER TECHNOLOGY CO., LTD Belongs to the following conditions, No matter whether the product is during the period of free warranty, are not within the free warranty: ■ The fault or the damage caused by without following manual request, wrongly install or use and so on.
- Page 12 L A S E R L E D / G R E E N D C L E D / G R E E N 3 0 . 5 1 2 . 5 2 7 0 . 4 1 2 . 5 6 5 .
- Page 13 L A S E R L E D / G R E E N D C L E D / G R E E N 1 2 . 5 2 7 0 . 4 1 2 . 5 4 8 V D C + 4 8 V D C - 6 5 .
Need help?
Do you have a question about the CR40C and is the answer not in the manual?
Questions and answers