Related Manuals for Laser Technology TruPulse 200
Summary of Contents for Laser Technology TruPulse 200
- Page 1 TruPulse Quick ® Reference Field Guides TruPulse Models: 200, 200 B, 360, 360 B and 360 R ® Authorized Distributor...
-
Page 2: Training Videos
LTI YouTube Channel: LTI Technical Support: ® Toll Free: 1.877.696.2584 www.youtube.com/lasertechpro Phone: 1.303.649.1000 for TruPulse Training Videos ® Email: support@lasertech.com Web: www.lasertech.com Fire Button Up Button Down Button LTI Hours of Operation: Monday through Friday TruPulse 200/B, 360/B ® 8:00 am to 5:00 pm (MST) (Excluding Holidays) Fire Button Down Button... - Page 3 TruPulse Values & Key Code: ® Measured by TruPulse: 1-Shot HD Mode: 2-Shot Missing Line: Calculated by TruPulse: = Horizontal Distance = Slope Distance = Vertical Distance = Height = Inclination 2-Shot Height: 3-Shot Height: = Azimuth (360 models) = Missing Line = Fire Button = Up Button = Down Button...
- Page 4 Change Units of Measurement: [1] Press-and-hold ), then press [2] Press to scroll through ( ) and press to choose. [3] Press to scroll through ( ) and press to choose. Turn On or Off Bluetooth ® (Models 200B, 360B/R) [1] Press-and-hold ), then press again (...
- Page 5 Required Clearances from TruPulse Compass: ® When firing the TruPulse 360, please maintain a safe clearance of: 6 in (15 cm) minimum: Metal rim glasses, pen/pencil, metal watch band, pocket knife, metal zipper/buttons, belt buckle, batteries, binoculars, cell phone, keys, camera, camcorder, survey nails, metal tape measure. 18 in (50 cm) minimum: Clipboard, data collector, computer, GPS antenna, 2-way radio, hand gun, hatchet, cell phone case with magnetic closure.
-
Page 6: Calibrate The Compass
Calibrate the Compass (Models 360/B/R) Always perform outside, away from magnetic interference and face towards Magnetic North. [1] Press-and-hold ), press until ( [2] Press ), press ), press [3] ( ), press ), press [4] Face North ( ), hold in position 1, press [5] Hold in position 2, press ), hold in position 3. - Page 7 Calibrate the Tilt Sensor (Models 360/B/R) Always perform on a flat, fairly level surface. For the TruPulse 360 R, you will need to use the edge of a surface to access the buttons in position 3. [1] Press-and-hold ), press until ( [2] Press ( )(...
-
Page 8: Measure Distance
Measure Distance: In HD Mode, it will automatically measure SD, INC and AZ* then calculate VD and HD. It outputs all the values via serial and/or Bluetooth ® (Models B & R only). Measurements are from the center of laser to target. [1] Press until ( *For TruPulse 360/B/R models only... - Page 9 Measure Height in 3-Shots: This routine is ideal for flat, vertical objects that do not lean. To shoot through brush, use the filter mode, foliage filter and a reflector. [1] Press until ( ) and ( ) flashes. [2] Aim anywhere you have a clear line of sight and press-and-hold Helpful Tip: [3] (...
- Page 10 Measure Missing Line (Models 360/B/R): Position yourself anywhere you have a clear line of site to your two targets. [1] Press until ( ) and ( ) flashes. [2] Aim at the 1st target, press-and-hold [3] ( ) Aim at 2nd target, press-and-hold [4] ( ), keep pressing to scroll through...