Safe Fleet HD1Q Series Quick Installation Manual

Specifications
Power Consumption 1 W (IR off); 2 W (IR on)
Operating Voltage Range 12 VDC ± 10% (powered by DVR)
Operating Temperature Range -4 to 122ºF (-20 to 50ºC)
Resolution 720p
Infrared LED Lamps 12 LEDs (5mm)
Minimum Illumination Color: 0.1 lux (F2.0)
B&W, IR LED on: 0 lux
Enclosure Size Diameter : 3.74" (95 mm)
Height: 2.64" (67 mm)
Enclosure Material Solid aluminum alloy
Dome Impact-resistant polycarbonate, anti-glare, scratch-
resistant hardcoating, UV protected
Camera Pigtail Connector Length 12" (30 cm)
Weight 0.642 lbs (0.29 kg)
Routine Maintenance
Most liquid cleaners or graffiti gel can be used to clean your camera enclosure. Do not use abrasive cleaners that can
scratch the window and reduce visibility of the camera.
Service
If your HD1Q camera is to be returned for service, please call (toll free) 1.877.630.7366 or 1.844.899.7366, and provide
the model and/or serial number of your unit. Ask for a Return Merchandise Authorization (RMA) number. An RMA number
allows the Service Technicians to better track your product when it comes in for service. Please show the RMA number on
the outside of the package. ANY PRODUCT SENT WITHOUT AN RMA# MAY BE REFUSED.
Technical Support Documentation
• Email: service@seon.com
Additional copies of this guide, along with supporting documentation, are available on
the SafeFleet Community:
• Phone: 1.877.630.7366
• https://community.seon.com/documents/
HD1Q Series Dome Camera
Product Overview
This quick install guide applies to the following camera models:
• HD1QxxAI, HD1QxxAI20, HD1QxxAI50, HD1QxxAI75
This HD1Q camera with IR is designed for interior use only.
The HD1Q camera can be installed with or without the supplied angle mount shim.
This guide covers both installation types, and provides specific instructions where required.
Installation Kit Contents
• 1 HD1Q camera, including dome and gasket
• 1 Security key (part # 645-1003)
• 3 x No. 10 screws *
(1" length, part # 600-1021)
• 1 Drilling template (Part # 700-1090) *
• 6 x rubber washers, pre-installed on screws
(part # 610-1001)
* Not used for shim installations
WARNING: Camera Harness Cable Compatibility
This camera requires a special Analog High Definition (AHD) camera harness - as indicated by a blue band in front of
the connectors. The AHD harness is not included with the camera kit. If you require an AHD harness, please contact
our customer service department to place an order.
Step 1: Choose Camera Location
When choosing a camera mounting location, consider the desired field of view, area of focus, and camera/shim assembly
orientation. For shim installations, generally the shallow side of the shim should point in the direction of the camera lens.
1. Determine the location for mounting the camera.
a. Choose a solid surface to minimize vibration
b. Choose a location away from access panels, hatches, or doors which may block the camera view
c. Choose a location away from heat sources
d. Cameras are usually installed with the cabling running inside the wall panels.
2. Mark the cable (7/8") and screw (5/32") on the panel:
• For shim installations: use the angle mount shim as a guide.
For standard installations: use the supplied drilling template.
•
3. Use a step-bit to drill the cable hole.
Quick Installation Guide
• 1 shim angle mount (part # 665-1017) **
• 2 x No. 10 screws **
(2" length, part # 600-1017)
• 1 x No. 10 screw **
(1.25" length, part # 600-1018)
** For shim installations only
© Safe Fleet | Oct. 2018 | All rights reserved | Part #: 700-1129 R1
