90(cm) Type C Charging Length 1 meter cable To protect the Charging charging Protect connector been Shield S�ck under the Non-slip depending on the situa�on M3x15 For rail securing Screw ACETECH Replacement for Velcro target ball Motor replacment Manual...
Precau�ons ※ Please remove the ba�ery insula�on tab before the first �me use and charge it for at least 6 hours.(The maximum charging current is 500mA.) ※ The target ball and connec�on part of AceTarget-D is consumable and not covered by the warranty. Consuming speed is varied by the frequence of usuage, and the velocity of the airso�...
Quick Start Guide 1. Assemble the rails and screw the "PCB Charging Protect Shield on the rail. 2. Remove the ba�ery insula�on tab and charge AceTarget for at least 6 hours before use. Make sure the charging connectors of the target and rail are on the same side.
Page 6
3. Turn off all the devices before se�ng the channel. And refer to page 5 for the se�ng details. Set up an Acetarget as "Host" and others are "Slave" If there are 2 sets of AceTarget systems in the same area, set the WIFI into differenct channels to avoid being bonded as one system.
Product Introduction 1. A recommended Target system is included 5pcs Acetarget S and 1pc Acetarget D. 2. AceTarget-D: The Moving ball target installed on the rail can be moved le� and right, and the rail extension length can be purchased, whole system execute by the smart device with WIFI connec�on,...
App Opera�on Guide 1. Download App Scanning the QR code on the package to download AceSo� Appy or searching on App Store (Apple) or Play Store (Android). Android 5.0 / iOS 10.0 or later is recommended Android 2. Connect Host Turn WiFi of the mobile device on and connect to AceTarget(1-8).
Make sure the mobile device has connected to Wi-Fi of AceTarget. Run the App, the app displays the following picture. Tap the device figure to enter the game se�ng. 3:09 3:09 AceTarget7 Connect to your Acetech Device Game--Shot Timer AceTarget Round--1 Duration of game --15 Start...
4. System Func�on Guidance: Tap 3:09 3:09 AceTarget7 System Status Target Number: 24 Game--Shot Timer Moving Target Number: 1 Round--1 Duration of game--15 Coin Slot Machine: 1 Lighter BT Start Game Record Device Joule ACETECH Record Device Joule Record ACETECH...
Page 11
◎ Tap , and the contraposed AceTarget-D rise and light up. 3:09 3:09 Target System Status System Status Target Number: 24 Moving Target Number: 1 Coin Slot Machine: 1 Lighter BT Device Joule Device Record ACETECH Joule Record ACETECH...
Page 12
◎ Tap Target Moving Target Number to see the mileage of AceTarget-D. Then, Tap the icon the selected AceTarget-D to turn on grenn light, and there will be a message on the App asking if you need to clear the mileage of AceTarget-D.
Rescue 遊戲紀錄 Compete Demo Cancel 裝置 記錄 Joule ACETECH 1) Shot Timer : 3:09 The Shot Timer game starts AceTarget8 a�er the countdown to 3 2 1 and all target face rise up. When �me is over or all the...
Page 17
4) Compete : 3:09 Compete game. Only one AceTarget7 AceTarget rise up at a �me. The higher the LEVEL is, the shorter the rising �me will be. Game--Compete One AceTarget-S rise up a�er Level --3 the former target is automa�cally down or manual hit down by the Round --3 shooter.
Page 18
2) Whack a Mole : 3:09 Whack a mole game. When the AceTarget7 game starts, the AceTarget-S rise up randomly. Game - --Whack a Mole According to the difficulty level of the game, there are up to 3 Level--2 AceTarget-S rising at the same Round --3 �me.
7. Game Record . Record points of each game separately. Take Quick Shoo�ng for example as shown below: A�er the the game, enter the User Name and tap Yes to keep the record. Tap the Record on the game page, and all the shoo�ng records can be seen.
Page 20
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec�on against harmful interference in a residen�al installa�on. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc�ons, may cause harmful interference to radio communica�ons.