Advertisement
Quick Links
Advertisement
Related Manuals for Acetech iTarget
Summary of Contents for Acetech iTarget
-
Page 2: Table Of Contents
Introduction to Product --------------------------------P2 Introduction to Each Unit -------------------------------P3 iTarget Setup --------------------------------------------P5 1-1 Setup of Round Target 1-2 iTarget System Wiring Instructions 1-3 iTarget System Setup Instructions 2-1 Controller Operation Instructions 2-2 Set Target ID 2-3 Set Moving Target ID... -
Page 3: Itarget-12T Kit Accessories
Kit Accessories Name Instructions Quantity Each iTarget is comes with an 8 cm and 10 cm Target round target 8 cm round target FPR material, thickness of 1.6mm 10cm round target FPR material, thickness of 1.6mm M3*10mm self-tapping screw 24 screws for normal use. -
Page 4: Introduction To Product
: 3 power consumption units Power consumption of controller : 1 power consumption unit For example: iTarget-12T kit accessories: target *12+ controller *1+ scoreboard *1=1*12+1*1+3*1=16 power consumption units 11. A set of iTarget can support up to 32 target connections (including 1 moving target). - Page 5 Introduction of Each Unit 1.Target : This device is responsible for raising and knocking down the target, and when setting up the target, it will give out a warning sound to alert the shooter.Meanwhile, LED will illuminate red or green light to add the fun of shooting on the target surface. (Figure 1.) A.
- Page 6 4.Moving Target: It is composed of a moving platform and an iTarget, so that the iTarget can move left and right, and the moving speed can be set to increase the fun and difficulty of the iTarget (Figure 4). A.Use the RJ45 cable connection to set up the system.
-
Page 7: Itarget Setup
The basic elements of iTarget system are controller and electronic target. Therefore, as long as there are controllers and more than 3 targets, an iTarget system can be set up. Moving target, scoreboard and start button are designed to increase the fun and difficulty of iTarget. - Page 8 6 iTargets, controller and start button sequentially. When all devices are connected, plug the adaptor into the power din of the PDU to power it. (The orange line represents RJ45 cable. Please refer to Chapter 1-2. iTarget System Wiring Instructions.)
- Page 9 2-1.Controller Operation Instructions : When the iTarget system is set up, plug in the power and turn it on. At this time, the controller OLED displays iTarget. Press any button of the controller to enter the System Status screen, press the “Right”...
- Page 10 2-4.Call Target Upon completion of ID setting, ITarget ID confirmation can be confirmed through this function. In the iTarget Setup screen, press the “Down” button to select Call ID, and press the “Right” button to perform this function. The target with ID=n will be called.
-
Page 11: Controller Operation Instructions
This feature Game Setup Compete is only displayed Shot Timer Start on the screen when Whack a Mole Level : 1 iTarget completes Rescue Round : 1 Compete its connection to Count : 100 *Remarks Demo the iTracer Unit. - Page 12 Game Setup : Select the game and set the game number and difficulty (see Unit 1 for details) Target Setup : Set up the ID of the iTarget and auto calibration of the motor (see Unit 3 for details) iTracer Pairing : Connect with the iTracer to execute a game...
- Page 13 The number of hostages in the rescue game is set as 1~1/2 of the number of iTargets. When the iTarget is set up, red light is projected on the target surface to indicate that it is a hostage. Shooting the hostage is prohibited;...
- Page 14 LEVEL=5 : moving target speed = 3, move left and right irregularly. ※SHOT Number : This parameter can only be set when the pairing of iTarget and iTracer Unit is completed. There are a total of 5 stages that can be set.
- Page 15 1. This game has TIME OUT, TIME OUT is the end of the game. N targets multiplied by 5 seconds E.g.: TIME OUT for 12 targets is 60 seconds. 2. SHOT parameters will only be displayed in the scoring information when the iTarget is connected to iTracer 3.
- Page 16 When the ID setting is completed, iTarget ID can be confirmed through this function. The iTarget with ID=n will be called. The No. n target will be raised up and the green LED will be projected, along with a beep sound.
- Page 17 Display brightness adjustment, you can adjust the brightness of the controller and scoreboard display. Sound : Volume adjustment, the controller button tone and iTarget prompt tone volume can be adjusted respectively, you can also turn off the sound. Warranty 1. Warranty is for 14 months. Free repair service for natural damage during warranty period 2.