Advertisement

Quick Links

Aruba AP-375ATEX Series Access Points
Installation Guide
The Aruba AP-375ATEX series access points support IEEE 802.11ac Wave 2 standard, delivering high
performance with the MU-MIMO (Multi-User Multiple-Input, Multiple-Output) technology, while also supporting
802.11a/b/g/n wireless services.
Package Contents
AP-375ATEX access point
Cable gland x1
USB console cable x1
Copper lug x1
M4x6 screw x1
The weatherproof caps for Ethernet and Console interfaces are connected to the access point, not loose in the
package.
Mounting kits for use with the access points are sold separately. Contact your Aruba sales representative for
details.
Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton,
including the original packing materials. Use these materials to repack and return the unit to the supplier if
needed.
Rev01 | November 2020
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AP-375ATEX Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Aruba AP-375ATEX Series

  • Page 1 The weatherproof caps for Ethernet and Console interfaces are connected to the access point, not loose in the package. Mounting kits for use with the access points are sold separately. Contact your Aruba sales representative for details. Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials.
  • Page 2: Hardware Overview

    Hardware Overview AP-375ATEX Front View Figure 1 System LED The access point is equipped with one LED that indicates the system status of the access point. Aruba AP-375ATEX Series Access Points | Installation Guide...
  • Page 3 The AP-375ATEX access point is equipped with one 10/100/1000 Base-T auto-sensing MDI/MDX Ethernet port. This port supports wired-network connectivity, in addition to Power over Ethernet (PoE) from IEEE 802.3at compliant power sources. | Installation Guide Aruba AP-375ATEX Series Access Points...
  • Page 4: Before You Begin

    FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80). Aruba AP-375ATEX Series Access Points | Installation Guide...
  • Page 5 After WLAN planning is complete and the appropriate products and their placement have been determined, the Aruba controller(s) must be installed and initial setup performed before the Aruba access points are deployed. For initial setup of the controller, refer to the ArubaOS Quick Start Guide for the software version installed on your controller.
  • Page 6: Installing The Access Point

    Identifying Specific Installation Locations You can mount the access point on a wall or pole. Use the AP placement map generated by Aruba’s RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference.
  • Page 7: Verifying Post-Installation Connectivity

    The integrated LEDs on the access point can be used to verify that the access point is receiving power and initializing successfully (see Table 1 Table 2). For instructions on initial setup and software configuration, refer to the AP Software Quick Start Guide. Electrical and Environmental Specifications | Installation Guide Aruba AP-375ATEX Series Access Points...
  • Page 8: Regulatory Model Number

    To view the FCC ID for controller-managed access points: 1. Log into the controller WebUI 2. Navigate to Maintenance > Controller > About To view the FCC ID for Instant access points: Aruba AP-375ATEX Series Access Points | Installation Guide...
  • Page 9 This device complies with Industry Canada's license-exempt RSS regulations. Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. | Installation Guide Aruba AP-375ATEX Series Access Points...
  • Page 10 If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally. Compliance is based on the use of Aruba approved accessories. Refer to the ordering guide for this access point at www.arubanetworks.com.
  • Page 11 +/- 0.5, 1.0, 2kV Conducted disturbances induced by RF fields: 0.15MHz-80MHz, 3Vrms Voltage Dips: 0%, 0.5 cycles, 0%, 1 cycle, 70% 25/30 cycles Voltage Interruptions: 0% 250/300 cycles Taiwan 第十二條   經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功 能。 第十四條 | Installation Guide Aruba AP-375ATEX Series Access Points...
  • Page 12 MINISTERS OF UKRAINE dated May 24, 2017, No. 355. The full text of the UA declaration of conformity is available at the following internet address: https://certificates.ext.hpe.com/public/certificates.html Х’ЮЛЕТТ ПАКАРД ЕНТЕРПРАЗ, 6280 АМЕРИКА ЦЕНТР Д-Р, САН-ХОСЕ, КАЛІФОРНІЯ 95002, США Aruba AP-375ATEX Series Access Points | Installation Guide...
  • Page 13 Oman OMAN - TRA D080320 R/5434/18 Philippines Type-Approval No. ESD-1816942C Singapore DB100427 | Installation Guide Aruba AP-375ATEX Series Access Points...
  • Page 14: Contact Aruba

    To obtain such source code, send a check or money order in the amount of US $10.00 to: Hewlett Packard Enterprise Company Attn: General Counsel 6280 America Center Drive San Jose, CA 94089 Warranty This hardware product is protected by an Aruba warranty. For more details, visit www.hpe.com/us/en/support.html Aruba AP-375ATEX Series Access Points | Installation Guide...

Table of Contents