Page 1
ORDER NO. MD9912156C2 MD Stereo System SA-PM30MD Colour (S)... Silver Type Area (EB)... Great Britain (EG)... Germany and Italy TAPE SECTION AR2 MECHANISM SERIES CD SECTION RAE0155Z TRAVERSE DECK SERIES MD SECTION MR3 MECHANISM SERIES Specification Amplifier Section Cassette Deck Section...
SA-PM30MD 1 Before Repair and Adjustment Disconnect AC power, discharge Power Supply Capacitors C905, C910 through a 10Ω, 5W resistor to ground. DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices. After repairs are completed, restore power gradually using a variac, to avoid overcurrent.
SA-PM30MD 4 Handling Precautions For Traverse Deck (CD/MD) The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static electricity of clothes or human body. So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup).
SA-PM30MD 5 Precaution of Laser Diode Caution : This product utilizes a laser diode with the unit turned "ON", invisible laser radiation is emitted from the pick up lens. Wavelength : 780 nm Maximum output radiation power from pick up : 100 mW/VDE Laser radiation from pick up unit is safety level, but be sure the followings: 1.
SA-PM30MD 8 Operation Check and Main Component Replacement Procedures “ATTENTION SERVICER” Some chassis components may have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components.
Page 10
SA-PM30MD 8.1.3. Checking for the Main P.C.B. • Check the Deck P.C.B. as shown. 8.1.2. Checking for the Transformer P.C.B. Step 2 Remove the panel in the direction of arrow. • Check the Main P.C.B. as shown. 8.1.4. Checking for the Tuner and FL P.C.B.
Page 11
SA-PM30MD Step 2 Desolder 6 points and remove the shield plate. • Check the CD Servo P.C.B. as shown. 8.1.6. Checking for the MD Servo P.C.B. • Check the Tuner and FL P.C.B. as shown. 8.1.5. Checking for the CD Servo P.C.B.
Page 12
SA-PM30MD 8.1.7. Checking for the Power P.C.B. Step 2 Lift up the Main P.C.B. together with the Power P.C.B. and rotate left then place the P.C.B. as shown in the following figure. • Check the Power P.C.B. as shown. 8.2.
Page 13
SA-PM30MD NOTE : 1. Follow the reverse procedure to replace the CD Traverse Unit and CD Tray. Step 2 Release the 2 claws and remove the clamp plate in the 2. Make sure that the 2 gear is in position shown above and direction of the arrow.
Page 14
SA-PM30MD 8.3. Main Component Replacement Procedure 8.3.1. Replacement of the CD Servo P.C.B. and Optical Pick-up Unit. Step 4 Push the lever in and turn the gear clock wise fully. Step 2 Desolder the 4 legs of 2 motors and flip over the CD Servo P.C.B.
Page 15
SA-PM30MD 8.3.2. Removal of the Deck P.C.B. and Mechanism P.C.B. for replacing parts. Step 7 Slide out the Optical Pick-up Unit from the indent opening. Step 2 Push the lever upward to open the cassette lid and remove the deck unit.
Page 16
SA-PM30MD Step 4 Set the holder ass’y and MD mechanism unit at a 60 degree angle and then pull out the holder ass’y. Step 7 Desolder the plunger terminals. Step 8 Release the 4 claws and remove the Mechanism P.C.B.
Page 17
SA-PM30MD Notice for installing the optical pickup Step 2 Align the guide portion (A) of optical pickup with the sub shaft. Note : Take care not to bend the FFC. Step 15 Remove the nut plate spring and nut plate.
Page 18
SA-PM30MD 8.3.4. Replacement for the Belt and Loading Motor Assembly Note : When installing the holder ass’y, align the lock lever pin with the main rack slot. Step 8 Set the holder ass’y and MD mechanism unit at a 60 degree angle, and then pull out the holder ass’y.
SA-PM30MD Notice for installing the traverse motor • Align the hole of traverse motor with the boss of mechanism chassis and then install the traverse motor. Step 3 Spread the lugs of head shifter and then release the lugs from boss.
Page 20
SA-PM30MD 8. Press "Stop" to indicate Error code.ve). 2. FL indicator shows “CLEAR” for 1 second and change to “TEST”. · If several problem exist, error code will change each time when "Stop" is pressed. 9.4. Cancelling the Self-Diagnostic (e.g. H01 → H03 → F01 ..etc.) mode 9.3.
SA-PM30MD 10 Measurement and Adjustment 10.1. Cassette Deck Section Measurement condition Test tape • Record timer : OFF • Headazimuth adjustment (8 kHz, -20 dB); QZZCFM • Make sure head, capstan and pressure roller are clean. • Tape speed adjustment (3 kHz, -10 dB); QZZCWAT •...
Page 22
SA-PM30MD 10.1.3. Bias Vlotage Check 1. Connect the measuring instrument as shown in Fig. 6. 2. Set the unit to “AUX” position. 3. Insert the normal blank tape (QZZCRA) and set the unit to “REC” mode (use “ REC/STOP” key).
Page 23
SA-PM30MD 10.3. Alignment Points <Cassette Deck> <Tuner> Fig. 9 Fig. 8 Fig. 10 10.4. Laser Power Adjustment Adjust each laser power : read power for reading (play) and fragile. Do not deform it. write power for writing (record). • Laser diode in the optical pickup may be destroyed by the staticelectricity generated in your clothes or 10.4.1.
Page 24
SA-PM30MD careful not to touch them with the edge of the laser Cautions power meter. Proceeding on to the subsequent adjustment procedure • The sensor of the laser power meter is a very fine part. with the read power exceeding 650µW will result in Be careful not to touch it to the optical pickup lens.
SA-PM30MD 12 Terminal Function of IC´s 12.1. IC1 (AN8772FHQ) : RF AMP Mark Function Mark Function CENVD — D signal det. capacitor connection OFT O Off track detection signal output terminal terminal Laser amp output terminal — GND terminal APCPD Photo diode light quantity det.
Page 27
SA-PM30MD 12.3. IC3 (MN66616RA4) : ATRAC ENCORDER/DECORDER, SERVO SIGNAL PROCESSOR Mark Function Mark Function ADIP ADIP FM signal input terminal DVss1 — GND terminal Lens position signal input terminal FS384 384 Fs output terminal Focus error signal input terminal Bit clock output terminal...
Page 28
SA-PM30MD 12.4. IC10 (MNBDF03DAA1) : SYSTEM CONTROL Mark Function Mark Function DACRST DAC reset signal output terminal to EEPDATA EEPROM data in/output terminal IC4 (“L”:Reset) (Connected to GND through resistor) DE emphasis signal output terminal TEST04 Test signal output terminal (Not to IC4(“L”:DE emphases)
Page 29
SA-PM30MD Mark Function SPMWE SPM take in test signal output terminal 12.5. IC72 (MNV4400-T8T) : 4M DRAM Mark Function Mark Function DRAM data 1 in/output terminal DRAM address 4~8 input terminal DRAM data 2 in/output terminal DRAM output enable input terminal...
Page 30
SA-PM30MD Mark Function Mark Function Spindle Motor Drive Signal SUBC Sub-Code Serial Data Output Output (Forced Mode Output) (Not Used, Open) Spindle Motor Drive Signal SBCK Clock Input for Sub-Code Serial Output. Data) (Servo Error Signal Output) KICK Kick Pulse Output...
Page 31
SA-PM30MD Mark Function Mark Function Motor Driver (1) forward - action Motor Driver (4) forward - action output output Motor Driver (2) reverse - action PVCC2 Power Supply (2) for Driver output PGND2 — Ground Connection(2) for Driver Motor Driver (1) forward - action...
Page 32
SA-PM30MD Mark Function Mark Function PLL CLK PLL Clock Output DES1 Destination Setup 1 (N.C) (Open) DES2 Destination Setup 2 (N.C) (Open) OPEN_H CD Tray Open Control (active H) TMRLED Timer LED Control Out (Timer Setting: L) CLOSE_L CD Tray Close Control...
SA-PM30MD 13 Block Diagram AN8772FHQ RF AMP MD OPTICAL PICKUP VREF OFT IN SELECT SERIAL & PARALLEL COMP SIGNAL CONV./GATE OFT O DARK DET. CBD O RF BDO COMP 3T DET. BDO/ NRFDET TRCRS TRCRS AS BDO COMP AS GAIN...
Page 34
SA-PM30MD IC11 IC72 TC74HCT00AFL NAND GATE MNV4400-T8T Q10,Q11 4M DRAM L700 HEAD MAGNETIC DRIVE HEAD RN5RZ26BA-TR NEFMON REGULATOR 1,2, 14~48 24,25 9~12 43~46 33~43 DIGITAL 74~77 MONI0~3 CHIP CONTROL NREFM 50 MSPMDARST EXTERNAL RAM NRST CONTROL PEFMS APCD APCREF APC GEN.
Page 40
SA-PM30MD FROM CD SIGNAL CD UNIT IC402 AUX (1) BH3857AFV-E2 JK603 SOUND PROCESSOR (12) (13) (14) (15) (16) (17) (18) (19) (20) MATRIX (BASS) SURROUND 1 Q401 MATRIX (Q501) TONE VOLUME SURROUND 2 MUTING (TREBLE) CONTROL VOLUME (23) OUT L(R)
Page 41
SA-PM30MD MD_LCH RECIN_L(R) MD CLK MDREQ IC803 IC802 TC4050BF 5V TO 3V TC74HCT7007A 3V TO 5V JK 605 OPT IN FROM CD UNIT MD CS MD DATA_OUT MD SYSRST MD DATA_IN LOADSW TO MD UNIT MOTOR (RM901) Q903,Q904 REGULATOR IC903...
SA-PM30MD 14 Schematic Diagram (All schematic diagrams may be modified at any time with : Playback signal line the development of new technology) Note : : Record signal line PROTECT detect switch REFLECT detect switch : FM signal line LOAD OPEN detect switch...
Page 52
SA-PM30MD 14.3. (M)Tuner Circuit SCHEMATIC DIAGRAM-9 : FM Signal Line : +B Line : AM Signal Line : -B Line : FM OSC Signal Line : AM OSC Signal Line : FM/AM Signal Line TUNER CIRCUIT Z120 FM FRONT END(EVN17290GIY)
Page 56
SA-PM30MD TIN L TVO L OUT L C609 50V1 C610 50V1 C611 50V1 AGCLK AGDATA AGCLK AGDATA AGLATH GLATCH C612 10V100 VREF D_GND AUX1_L PORT 4 P-MD_L PORT 3 PORT 2 PORT 1 C617 16V470 PB_LCH OUT R PB_RCH TVO R...
Page 57
SA-PM30MD R891 2.7K {0V} {3.4V} {0V} {5V} {3.4V} {3.2V} {3.7V} {4.6V} {3.4V} {0V} {3.4V} {4.8V} {4.6V} {0V} CD_LCH CD Lch A GND CD Rch CD_RCH C672 3.3V 1000P LD SW C676 D GND 220P CD 7V C675 PWR GND R681...
Page 58
SA-PM30MD D961 RVD1SS133TA BVO L TIN L BIN L TVO L BVN L OUT L C609 50V1 SO L D923 C610 S133TA 50V1 SNF L C611 50V1 SIN L PWRCONT1 BUOUT L AGCLK NF L AGDATA RM_VCC IN L AGLATCH...
Page 59
SA-PM30MD 14.6. (D) FL Circuit (E) Control Circuit (I) Motor Circuit SCHEMATIC DIAGRAM-13 : +B Signal Line : -B Signal Line FL CIRCUIT Z801 RSL0289-F 60 59 30 29 8 7 6 C706 50V22 R704 R703 4.8V 4.8V L706 ((4.8V)) Q701 ((4.8V))
Page 60
SA-PM30MD SCHEMATIC DIAGRAM-14 : -B Signal Line : +B Signal Line Z751 RCDRPM6937V4 R786 IC903 1.3mA RM_VCC IC903 BA6283N MOTOR DRIVER RM_IN R785 C791 C792 8.8V 4.9V 0.01 6.3V47 ((0V)) ((0V)) ((0V)) ((8.8V)) ((0V)) ((4.9V)) ((0.1V)) ((0V)) ((0.1V)) {0V} {0V} {0V} {8.8V}...
Page 61
SA-PM30MD 14.7. (N) Power Circuit SCHEMATIC DIAGRAM-15 : +B Signal Line : Main Signal Line POWER CIRCUIT IC404 IC404 AN7194K-LD LOW AMP PWR OFF POP D636 RVD1SS133TA D637 RB441Q40T77 {18.6V} {8.6V} {0V} {0V} {7.4V} {0V} {4.7V} {9.4V} {8V} {0V} {0V} {0V} {8.6V} {0V}...
Page 73
SA-PM30MD TRANSFORMER P.C.B (REP2858D) CAUTION AC IN F1 250V T630mA RISK OF ELECTRIC SHOCK 220V-230V...EG AC VOLTAGE LINE. PLEASE DO NOT 230V-240V...EB TOUCH THIS PCB 50HZ T2 (SUB-TRANSFORMER) T1 (POWER TRANSFORMER) 5000...
SA-PM30MD 18 Parts Location and Replacement Parts List Notes: • Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardent (resistors), high-quality sound (capacitors), low noise (resistors), etc are used.
Page 85
SA-PM30MD 18.1.2. Deck Mechanism Parts List Ref. Part No. Part Name & Description Remarks RMQ0519 REEL HUB Ref. Part No. Part Name & Description Remarks RMS0398-1 MOVING CORE RSJ0003 PLUNGER CASSETTE DECK RMC0061 PACK SPRING RXF0049 FLYWHEEL ‘F’ ASS’Y RED0043...
Page 87
SA-PM30MD Ref. Part No. Part Name & Description Remarks 18.2.2. MD Mechanism Parts List 411-5 RMQ0752 PIN A (BLACK) Ref. Part No. Part Name & Description Remarks 411-6 RMQ0753 PIN B (NATURAL) 411-7 XQN17+C25FZ MOTOR SCREW TRAVERSE DECK 411-8 XYC2+FF105...
Page 88
SA-PM30MD 18.3. CD Loading Mechanism 18.3.1. CD Loading Mechanism Parts Location...
Page 89
SA-PM30MD 18.3.2. CD Mechanism Parts List Ref. Part No. Part Name & Description Remarks TRAVERSE DECK RAE0155Z CT100 TRAVERSE RDG0455 TRAVERSE GEAR (A) RDG0456 TRAVERSE GEAR (B) RFKNCT100 TRAVERSE BASE ASS’Y 304-1 RDG0457 LOAD GEAR (A) 304-2 RDG0458 LOAD GEAR (B)
Page 90
SA-PM30MD 18.4. Cabinet 18.4.1. Cabinet Parts Location...
Page 92
SA-PM30MD Ref. Part No. Part Name & Description Remarks 18.5. Electrical Parts List Q613 RVTDTA114EST TRANSISTOR Ref. Part No. Part Name & Description Remarks Q621 2SC1740SRTA TRANSISTOR Q671 RVTDTC143EST TRANSISTOR P.C.B. Q672 RVTDTC143EST TRANSISTOR Q673 2SC1740SRTA TRANSISTOR REP2575A SWITCH PCB UNIT...
Page 93
SA-PM30MD Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks RVD1SS133TA DIODE RSH1A045-1A TRIGGER SWITCH SC80209TE12R DIODE RSP1A023-A TRV-IN SWITCH RL1N4003N02 DIODE S701 RSH1A048-A SW RESET RL1N4003N02 DIODE S971 RSH1A018-3U MODE SWITCH MA728TX...
Page 94
SA-PM30MD Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks RLQU100KT-W CHIP COIL FUSE RLQZ371 CHOKE COIL RLQU101KT-W CHIP COIL XBA2C06TB0L FUSE RLQU101KT-W CHIP COIL RLQU2R2MT-W CHIP COIL FUSE HOLDER RLQU2R2MT-W CHIP COIL...
Page 95
SA-PM30MD Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks ERJ3GEYJ223V 22K 1/16W R109 ERJ3GEYJ102V 1K 1/16W ERJ3GEY0R00V 0 1/16W R110 ERDS2TJ562T 5.6K 1/4W ERJ3GEYJ272V 2.7K 1/16W R110 ERJ3GEYJ102V 1K 1/16W ERJ3GEYJ473V 47K 1/16W...
Page 96
SA-PM30MD Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R417 ERDS2TJ473T 47K 1/4W R621 ERDS2TJ272T 2.7K 1/4W R421 ERDS2TJ223T 22K 1/4W R624 ERDS2TJ333T 33K 1/4W R423 ERDS2TJ104T 100K 1/4W R625 ERDS2TJ333T 33K 1/4W...
Page 97
SA-PM30MD Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R751 ERDS2TJ102T 1K 1/4W R837 ERDS2TJ561T 560 1/4W R752 ERDS2TJ102T 1K 1/4W R838 ERDS2TJ104T 100K 1/4W R753 ERDS2TJ122T 1.2K 1/4W R839 ERDS2TJ104T 100K 1/4W...
Page 98
SA-PM30MD Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R977 ERDS2TJ102T 1K 1/4W R1355 ERDS2TJ222T 2.2K 1/4W R978 ERDS2TJ102T 1K 1/4W R1391 ERDS2TJ223T 22K 1/4W R984 ERDS2TJ101T 100 1/4W R1395 ERDS2TJ103T 10K 1/4W...
Page 99
SA-PM30MD Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks ECUVNC104ZFV 0.1 16V C129 ECUV1H101JCV 100P 50V ECUVNC104ZFV 0.1 16V C130 ECEA0JKA101B 100 6.3V ECUVNC104ZFV 0.1 16V C131 ECBT1H101KB5 100P 50V ECUVNC104ZFV 0.1 16V...
Page 100
SA-PM30MD Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C464 ECQV1H224JZ3 0.22 50V C707 ECUV1E273KBN 0.027 25V C465 ECBT1H102KB5 1000P 50V C708 ECBT1C103MS5 0.01 16V C501 ECA1EAK100XB 10 25V C709 ECEA0JKS101B 100 6.3V...
Page 101
SA-PM30MD Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C815 ECBT1H102KB5 1000P 50V C1114 ECBT1H102KB5 1000P 50V C816 ECBT1H102KB5 1000P 50V C1115 ECBT1H101KB5 100P 50V C817 ECBT1H150JC5 15P 50V C1202 ECBT1C152MR5 1500P 16V...
Page 102
SA-PM30MD Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks EUR647201 REMOTE CONTROL RQT5149-H O/I BOOK [M]EG A1-1 UR64EC1822R R/C BATTERY COVER RQT5151-B O/I BOOK [M]EB RJA0019-2K AC CORD (SF) [M]EG RSA0007 FM ANTENNA...