Bass - LG MU-42PM11, MU-42PM12X, MU-42PM20, MU-50PM10, MU-50PM11, MU-50PM20 Owner's Manual

18. Bass (Command2:s)
G To adjust bass.
You can also adjust bass in the Sound menu.
Transmission
[k][s][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
•
Refer to 'Real data mapping 1'. See page 31.
Acknowledgement
[s][ ][Set ID][ ][OK][Data][x]
19. Balance (Command2:t)
G To adjust balance.
You can also adjust balance in the Sound menu.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
•
Refer to 'Real data mapping 1'. See page 31.
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
20. Color Temperature (Command2:u)
G To adjust color temperature.
You can also adjust ACC in the Picture menu.
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Data 0: Cool 1: Normal 2: Warm
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
21. Red Adjustment (Command2:v)
G To adjust red in color temperature.
Transmission
[k][v][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 3C
•
Refer to 'Real data mapping 3' as shown right.
Acknowledgement
[v][ ][Set ID][ ][OK][Data][x]
22. Green Adjustment (Command2:w)
G To adjust green in color temperature.
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 3C
•
Refer to 'Real data mapping 3' as shown right.
Acknowledgement
[w][ ][Set ID][ ][OK][Data][x]
23. Blue Adjustment (Command2:$)
G To adjust blue in color temperature.
Transmission
[k][$][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 3C
Acknowledgement
[$][ ][Set ID][ ][OK][Data][x]
24. SUB INPUT Select (Command2:y)
G To select input source for sub picture in PIP mode.
Transmission
[k][y][ ][Set ID][ ][Data][Cr]
Data 0: RGB
3: Off
Acknowledgement
[y][ ][Set ID][ ][OK][Data][x]
25. Abnormal State (Command2:z)
G To recognize an abnormal state.
Transmission
Data FF:Read
Acknowledgement
[z][ ][Set ID][ ][OK][Data][x]
Data 0: Normal (Power on and signal exist)
•
Refer to 'Real data mapping 3' as shown below.
* Real data mapping 3
0 : -30
1 : -29
2 : -28
1E : 0
3A : +28
3B : +29
3C : +30
1: DVI
2: Component 3: Video
[k][z][ ][Set ID][ ][FF][Cr]
1: No signal (Power on).
2: Turn the monitor off with remote control.
3: Turn the monitor off with Sleep Time function.
4: Turn the monitor off with RS-232C function.
5: 5V down.
6: AC down.
7: Turn the monitor off with Fan Alarm function.
8: Turn the monitor off with Off Time function.
9: Turn the monitor off with Auto Off function.
a: Turn the monitor off with On Time function.
* This function is "read only".
External Control Device Setup
4: S-video
Owner's Manual 33