Table of Contents
Advertisement
Quick Links
Diagram may show a different but similar model. Rafter spacing and overall length may vary.
©2008 ClearSpan™
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 06.11.08
ClearSpan
Portable Freestanding Building
CLEARSPAN
GARAGES & STORAGE SHEDS
™
™
STK#
DIMENSIONS
PB00562R3S
14' W x 14' H x 24' L
PB00564R3S
14' W x 14' H x 28' L
PB00566R3S
14' W x 14' H x 36' L
PB00562R4S
14' W x 14' H x 24' L
PB00564R4S
14' W x 14' H x 28' L
PB00566R4S
14' W x 14' H x 36' L
1
Advertisement
Table of Contents
Related Manuals for ClearSpan PB00562R3S
Summary of Contents for ClearSpan PB00562R3S
- Page 1 ™ Portable Freestanding Building Diagram may show a different but similar model. Rafter spacing and overall length may vary. STK# DIMENSIONS PB00562R3S 14' W x 14' H x 24' L PB00564R3S 14' W x 14' H x 28' L PB00566R3S 14' W x 14' H x 36' L ©2008 ClearSpan™...
-
Page 2: Safety Precautions
• Never erect the structure under power lines. • Identify whether underground cables and pipes are Thank you for purchasing this ClearSpan™ shelter. When present before preparing the site or anchoring the properly assembled and maintained, this product will structure. -
Page 3: Assembly Procedure
These words and phrases are common to most joints and to fasten brackets to rafters. ClearSpan™ shelters and identify the different parts of the shelter. (Some are used in this document. Others may not apply to this particular shelter.) These terms describe the shipped parts and can also be found on the materials list/spec sheets included with the shipment. -
Page 4: Required Tools
CLEARSPAN GARAGES & STORAGE SHEDS ™ SPECIAL NOTE: Wheel Jack Mounting Board REQUIRED TOOLS These instructions describe installing a mounting board The following list identifies the main tools needed to on the inside of the frame. The mounting board runs from assemble the shelter. - Page 5 CLEARSPAN GARAGES & STORAGE SHEDS ™ The following graphics and photos will help you identify the different parts and show you how they are used. (All parts are not shown.) FA4482B Tek Screw ATTENTION: Actual wheel jack assembly may differ slightly in design from what is shown.
- Page 6 CLEARSPAN GARAGES & STORAGE SHEDS ™ Round Style Portable Freestanding Building NOTE: Diagram shows a shelter with OVERVIEW 4' rafter spacing. Number of rafters and ratchet locations may vary for the shelter This section is an overview of the process for assembling with the 3' rafter spacing.
-
Page 7: Rafter Assembly
CLEARSPAN GARAGES & STORAGE SHEDS ™ ASSEMBLING THE ROUND STYLE PORTABLE FREESTANDING COMPONENTS NOTE: Assistance is required to assemble the shelter. RAFTER ASSEMBLY Gather the Parts: 1˝ • Round Raft Position #1 (Pipe #14R1601) Tek screw • Round Raft Position #2 (Pipe #14R1602) •... -
Page 8: Frame Assembly
Check that the rafter is standing up straight (plumb). Position the bolt side of end clamp to the inside of the frame. SKU # Rafter Spacing center-to-center PB00562R3S 36" PB00564R3S 37-5/16" ATTENTION: PB00566R3S 36"... - Page 9 CLEARSPAN GARAGES & STORAGE SHEDS ™ FRAME ASSEMBLY (CONTINUED) MOUNTING BOARD INSTALLATION 10. Continue adding rafters and purlins until the frame is The mounting board is supplied by the customer. For this assembled. (Remember to slide a band clamp onto...
-
Page 10: Strut Assembly
CLEARSPAN GARAGES & STORAGE SHEDS ™ MOUNTING BOARD INSTALLATION (continued) STRUT ASSEMBLY After the rafter assembly is complete and the mounting 2. Secure the mounting boards to the interior rafters using boards are attached, verify that the band clamps are in the two (2) U-bolts, four (4) nuts and washers. - Page 11 CLEARSPAN GARAGES & STORAGE SHEDS ™ FINISH ROUGH EDGES INSTALL PIVOT WHEEL ASSEMBLY Gather the parts: When the wheel pivot wheel assembly is properly installed and locked in the down position, the frame assembly will be • Duct tape (supplied by customer) off the ground.
- Page 12 CLEARSPAN GARAGES & STORAGE SHEDS ™ 2. Assemble two cover conduits. Start each conduit PREPARE MAIN COVER assembly with one plain pipe and add 75" swaged Gather the parts: pipes to arrive at the correct length. Secure each pipe joint with a Tek screw and wrap each joint using •...
- Page 13 CLEARSPAN GARAGES & STORAGE SHEDS ™ ATTACH MAIN COVER 4. Once the main cover is pulled into position, center the cover on the frame and remove the ropes. Loosely Gather the parts: secure the ends of the cover to the ratchets attached to the front and back end rafters.
- Page 14 NOTE: With the exception of Truss Arch buildings, 13. Continue by reading the care and maintenance ClearSpan™ shelters and greenhouses do not have any information that follows. tested loading criteria. Revision date: 06.11.08...
- Page 15 CLEARSPAN GARAGES & STORAGE SHEDS ™ QUICK START GUIDE 14' Wide Round Style Portable Freestanding Building Frame shown may differ in length and rafter spacing from actual frame. Revision date: 06.11.08...
- Page 16 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 17 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 18 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 19 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 20 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 21 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 22 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 23 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 24 CLEARSPAN GARAGES & STORAGE SHEDS ™ Revision date: 06.11.08...
- Page 25 CLEARSPAN GARAGES & STORAGE SHEDS ™ Space below reserved for customer notes. Revision date: 06.11.08...
Need help?
Do you have a question about the PB00562R3S and is the answer not in the manual?
Questions and answers