Related Manuals for Pantum PT-B680 Series
Summary of Contents for Pantum PT-B680 Series
- Page 1 User Manual Pantum PT-B680 Series Barcode Printer It is recommended to read the Manual carefully before use...
-
Page 2: Table Of Contents
Contents About the Manual ..............................1 Safety Information ............................2 Legal Information ..............................5 Chapter 1 Product Description ........................6 1.1 Unpacking Checklist ..........................6 1.2 Appearance and Components .........................7 1.3 Product dimensions ..........................9 Chapter 2 Product specifications ....................... 10 Chapter 3 Installation and Use ........................12 3.1 Components installation ........................ -
Page 3: About The Manual
PT-B680 Series User Manual About the Manual The Manual contains basic information on product use, installation and other respects. The following provides more detailed information on various technical problems and areas. -
Page 4: Safety Information
PT-B680 Series User Manual Safety Information Before using the printer, please read the following precautions carefully to avoid personal injury or equipment damage. 1. Safety Warning Signs --------Warning: Must be observed to avoid personal injury or equipment damage. --------Note: Give important information and tips for operating the printer. - Page 5 PT-B680 Series User Manual Install the printer on a stable, flat surface. • If the printer falls, it can be broken and cause personal injury. Use only approved accessories and do not try to disassemble, repair or remodel it for yourself.
- Page 6 PT-B680 Series User Manual 4. WEEE (Waste Electric and Electronic Equipment) This marking or its literature indicates that it should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
-
Page 7: Legal Information
Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits. The manufacturer of this product is: Zhuhai Pantum Electronics Co.,Ltd., No.3883, Zhuhai Avenue, Zhuhai, Guangdong, China 519060. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative. -
Page 8: Chapter 1 Product Description
PT-B680 Series User Manual Chapter 1 Product Description 1.1 Unpacking Checklist Note: 1) Open the printer package and keep the packing materials for future packing and shipping. 2) If any items are damaged or missing, please contact the dealer who sells the product. -
Page 9: Appearance And Components
PT-B680 Series User Manual 1.2 Appearance and Components... - Page 10 PT-B680 Series User Manual Note: During use, keep your fingers as far away as possible from the paper cutter to avoid injury to your hands. We are not responsible for any injuries caused by the paper cutter during use.
-
Page 11: Product Dimensions
PT-B680 Series User Manual 1.3 Product dimensions... -
Page 12: Chapter 2 Product Specifications
PT-B680 Series User Manual Chapter 2 Product specifications Model PT-B680 Series Print method Thermal direct/thermal transfer Resolution 300dpi(11.8dots/mm) Printing Maximum print speed 203mm/s(Max) Maximum print width 106.7mm Label print length 710mm(27.9") Continuous Paper, Gap Paper, Folding Paper, Black Mark Paper type... - Page 13 PT-B680 Series User Manual Model PT-B680 Series Programming language Printhead life 30km Working 5°C ~45°C，25%-85%RH Environmental parameters Storage -10°C ~50°C，10%~90%RH Product dimensions 425mm×255mm×265mm (L×W×H) Product weight 9.65 KG Physical parameters Packing dimension 525mm×365mm×375mm (L×W×H) Packing weight 11.95 KG GRF, PNG format (other formats need to be converted to GRF...
-
Page 14: Chapter 3 Installation And Use
PT-B680 Series User Manual Chapter 3 Installation and Use 3.1 Components installation 3.1.1 Installing the paper roll 1. Fix the paper loading block horizontally, move it to the extreme extent and wrench it flat. 2. Install the paper roll on its mounting shaft, hold the loading block upright and adjust it to the proper... - Page 15 PT-B680 Series User Manual 3. Push the printhead cover hook in the direction of the arrow as shown in the figure to open the printhead. 4. Pass the front end of the paper through the flexible paper guiding channel and extend the paper through the gap black-mark sensor toward the printhead exit to the first sheet sensor.
- Page 16 PT-B680 Series User Manual 5. Adjust the paper clamping block to fit the paper width. To adjust the gap black-mark sensor, make sure that the paper gap (or black mark) passes through the triangular position of this sensor. 6. Press both ends of the printhead as shown, close the printhead and make sure that the cover hook...
-
Page 17: Installing The Ribbon
PT-B680 Series User Manual 3.1.2 Installing the ribbon 1. Lift the right cover of the printer and install the ribbon and the empty paper roll on the ribbon supply spindle and the ribbon recovery spindle respectively. 2. Push the printhead cover hook in the direction of the arrow as shown in the figure to open the ribbon... - Page 18 PT-B680 Series User Manual 3. Pass the front end of the ribbon under the ribbon guiding bar and through the ribbon sensor, then pull it forward and out. (Refer to the “Ribbon Installation Path” as illustrated below). 4. Attach the front end of the ribbon to the empty paper roll on a flat and wrinkle-free basis.
- Page 19 PT-B680 Series User Manual 6. Press both ends of the ribbon holder as shown, close the ribbon holder and make sure that the cover hook snaps into the groove for a fully closed state.
-
Page 20: Power Connection
PT-B680 Series User Manual 3.2 Power connection 1. Make sure that the power switch is off (O). 2. Connect the power cord to the printer. 3. Connect the other end of the power cord to a nearby outlet. Power cord Note: •... -
Page 21: Interface Connection
PT-B680 Series User Manual 3.3 Interface connection Connect the interface cable as shown in the figure below. The printer supports the following communication interface standards: --USB B-Type cable 1) Turn off the printer (O). 2) Plug the communication cable to be used into the corresponding communication connection plug. -
Page 22: Operating Interface Description
PT-B680 Series User Manual 3.4 Operating Interface Description ◼ Power on When the printer is powered off, turn on the power switch on the back of the printer, and then the printer turns on and the indicator lights. ◼ Power off When the printer is powered on, turn off the power switch on the back of the printer, and both printer and indicator turns off. -
Page 23: Basic Functions
PT-B680 Series User Manual 3.5 Basic functions 3.5.1 Power on/off Turn on the power switch to the I state. Turn off the power switch to the O state. 3.5.2 Print test When the printer is initially installed or there is any problem with the printer, self-test procedure can be executed to confirm the following status, firmware version, printer parameter setting, print quality, external settings and other related setting information. -
Page 24: Chapter 4 Ports
PT-B680 Series User Manual Chapter 4 Ports 4.1 USB Pin No. Signal name VBUS 4.2 Serial port Pin No. Signal name... -
Page 25: Network Port
PT-B680 Series User Manual 4.3 Network port Pin No. Signal name... -
Page 26: Chapter 5 Printer Cleaning
PT-B680 Series User Manual Chapter 5 Printer Cleaning Dust, foreign objects, viscous material, or other contaminants stuck in the printhead or printer may reduce print quality. Please clean the dirty printhead as follows: Note: 1) Be sure to turn off the printer before cleaning. -
Page 27: Chapter 6 Driver Installation
PT-B680 Series User Manual Chapter 6 Driver Installation 6.1 Driver installation for Windows system 1) Run the Pantum_2021.2_M-0 (subject to change with version updates) file 2) Accept the terms and conditions and select Next 3) Select the installation directory and click Next, or you can default the directory and go directly to the... - Page 28 PT-B680 Series User Manual 4) Complete the installation ============================================================================= The following is an example of installing the printer driver USB Preparations for installation 1. Connect the printer to the computer using the USB cable 2. Power on the printer 3. Select Install Driver and click Next...
- Page 29 PT-B680 Series User Manual 1) The model number is automatically recognized 2) Follow the instructions and click Next to complete the installation Note: If you use other ports, please select Other...
-
Page 30: Driver Installation For Linux System
PT-B680 Series User Manual 6.2 Driver installation for Linux system 1) Open the driver package folder, open the terminal, type sudo dpkg -i and drag in the driver package, click “Enter”. 2) Enter your computer password and click “Enter”. - Page 31 PT-B680 Series User Manual 3) After installing the driver, close the terminal. 4) Open the computer settings, then open Devices, select Printers, and click Add Printer.
- Page 32 PT-B680 Series User Manual 5) Click Add in the upper left corner. 6) Select the printer you want to add and click Forward.
- Page 33 PT-B680 Series User Manual 7) Click Apply. 8) Select Print Test Page. If the test page prints out normally, the printer has been successfully installed.
-
Page 34: Bartender Registration Guidelines
PT-B680 Series User Manual 6.3 Bartender registration guidelines 1) Access the software installation and activation guidelines; ====================================================== ======================================================... - Page 35 PT-B680 Series User Manual Enter the product key code; Z2WV-893L-B2SJ-5SDW...
- Page 36 PT-B680 Series User Manual Select the server;...
- Page 37 PT-B680 Series User Manual Complete the Bartender software activation.
-
Page 38: Appendix 1: Statement For Pollution Control Of Electronic Information Products
PT-B680 Series User Manual Appendix 1: Statement for Pollution Control of Electronic Information Products 1. The name and content of hazardous substances in the product: Toxic and hazardous substances or elements Chromium Polybrominated Polybrominated Component Lead Mercury Cadmium biphenyls diphenyl ether... - Page 39 Pantum International Limited Manufacturer: Zhuhai Pantum Electronics Co., Ltd. Website: www.pantum.com Address/Adresse: Building02,06 and 08, No.888 Shengping Avenue, Pingsha Town,Zhuhai City, Guangdong Province, 519000 PR China...