(SEE WARRANTY SECTION FOR MORE INFORMATION) You can register your warranty online by visiting www.info@ardisam. com, or by mailing it to: Ardisam, 1160 8Th Avenue, Cumberland, WI 54829. You may also call our Customer Service department at (800) 345-6007 Mondays through Fridays from 8 a.m. to 5 p.m.
TRIANGLE IN THE TEXT SIGNIFIES IMPORTANT combustion engine to power the tines. It shall not be used for CAUTIONS OR WARNINGS WHICH MUST BE any other purpose. FOLLOWED. DANGER For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
Page 4
• Disengage all clutches and leave control lever in the can cause drowsiness or affect your ability to operate neutral position before starting the engine. this machine safely. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
Page 5
Stop engine and allow to cool before filling. • Do not smoke. • Never drain fuel from engine in an enclosed area. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
Page 6
WHEN WORKING ON OR REPLACING PARTS FOR important details if the tiller is to be stored for an THE ENGINE OR PRODUCT, YOU MUST ALWAYS extended period. FLIP THE ON/OFF SWITCH TO THE OFF POSITION. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
Correct Tine Installation Tail Mount Decal Part No. 17052 MOVING PARTS WARNING Frame Near Belt Decal Part No. 17049 Part No. 17050 MULTI INJURY WARNING TINES DANGER/OPERATION Hood Decal Hood Decal For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
N. Team Lift--For your safety, always have at least two people when lifting this machine. O. Do Not Till Above Underground Utility Lines And Pipes. P. Do Not Operate When Children Or Others Are Around. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
3-POSITION KOHLER HANDLE ENGINE BAR HEIGHT ADJUSTMENT BUMPER LARGE 2-POSITION WHEELS FRONT BELT COVER ADJUSTABLE DEPTH REGULATOR TINE SHIELD 3-WAY ADJUSTABLE TINE WIDTHS TRANSPORT POSITION OPERATING POSITION FIGURE 1 For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
5. Insert depth regulator/drag stake through opening in lower LOWER BOLT tail mount from the bottom up and secure with lock pin. SEE FIGURE 6 LOWER LOOP MOUNT 6. Add and check engine oil. FIGURE 5 For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
If no more adjustment can be made, belt may have to be replaced. SEE FIGURE 9 operate your unit, learn and understand the purpose for each symbol. On/O Choke Fuel Shuto FIGURE 7 For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
Page 12
• FAILURE TO FOLLOW INSTRUCTIONS CAN CAUSE 3. Align hole in depth regulator lever with hole in depth INJURY. regulator bracket and replace lock pin. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
2. Place the tiller in motion by pushing down on the drive safety control lever; this will engage the tines. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
ENGINE MUST BE TURNED OFF AND COOL, AND SPARK PLUG WIRE MUST BE REMOVED AND SECURED FROM SPARK PLUG BEFORE CHECKING AND ADJUSTING ENGINE OR EQUIPMENT. ACCIDENTAL ENGINE START CAN CAUSE SERIOUS INJURY. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
Page 15
2. Change oil after first three to five hours of operation. 6. Attach spark plug wire. 3. Change oil while engine is warm. Refill with new oil of recommended grade. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
PLUG WIRE MUST BE DISCONNECTED AND SECURED BEFORE ATTEMPTING ANY MAINTENANCE OR REPAIR. FAILURE TO COMPLY WITH THIS SAFETY REQUIREMENT CAN RESULT IN SERIOUS PERSONAL INJURY TO YOU OR BYSTANDERS. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
• Adjust engage cable. • Replace spark plug wire. Excessive heat build up in transmission/tine area during tilling • Remove vegetation. • Check transmission fluid and fill if needed. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
Operator’s Manual 20970 Front Tine Tiller For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
Page 19
SPRING, COMPRESSION (FORWARD ARM) 20819 BOLT (M10 X 1.5 X 30 HHSF GR8.8 ZN) 4620 NUT (M8 X 1.25 HJAM GR8.8 13508 NUT (M8 -1.25 BAR) 53629 BRACKET, CABLE MOUNT For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
Page 20
Operator’s Manual 20970 Front Tine Tiller ILLUSTRATED PARTS BREAKDOWN 20970 TINES AND TRANSMISSION ASSEMBLY For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
Page 21
* ITEM NOT ILLUSTRATED; INCLUDES: (2) 13903 INSIDE TINE SET, (1) 13904 LEFT TINE SET, (1) 13905 RIGHT TINE SET, (1) 3157 DRAG STAKE, AND (1) 3331 WHEEL SHAFT IN A BOX. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
Page 22
Operator’s Manual 20970 Front Tine Tiller ILLUSTRATED PARTS BREAKDOWN - MOTOR MOUNT AND HOOD PARTS 35 36 For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
SPACER FORWARD ARM 10.5 X 22 X 14.5 MM 3157 DRAG STAKE FRONT TINE 20834 BELT GUIDE AND MOUNT 17623 TAIL MOUNT, LOWER ORANGE METRIC 3365 SERIES 20886 TAIL MOUNT, UPPER ORANGE For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5 CST...
Page 24
All weights, specifications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Items used for props not included. Some assembly may be required. For additional information email info@ardisam.com or call 800-345-6007 M-F 8-5...