Page 1
SKYLINE 10' x 10' SINGLE-TIER GAZEBO PRODUCT NO. 088-2258-8 ASSEMBLY INSTRUCTIONS HAVING TROUBLE? TOLL-FREE: Scan the QR 1-888-670-6684 code for online assembly instruction video. IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference.
Page 2
We would love to hear from you and welcome your thoughtful feedback. Visit our website at canadiantire.ca to tell us about your experience, and share your photos with us using #myCANVASstyle. Show us how you bring CANVAS TM/MC products to life. We can’t wait to see!
Page 3
IMPORTANT HOW TO USE OUR QR CODES Follow the steps below to scan our QR codes and access helpful assembly videos. Open the Wait for the camera on camera to your smart recognize device and and scan point it at the QR code.
TABLE OF CONTENTS Warnings Required and Recommended Tools Important Safety Information Parts List Hardware List General Preparations Step-by-Step Guide Caring for Your Item Warranty WARNING! TO REDUCE THE RISK OF SERIOUS INJURY, READ THE FOLLOWING SAFETY INFORMATION. Caution! Always keep children under close supervision while they are playing around this product.
Page 5
TOOLS REQUIRED 8' (2.4 m) ladder 15' (4.6 m) tape (Qty. 1 recommended) measure people RECOMMENDED TOOLS Socket wrench with Cordless drill or Driver bit extension driver with 4 mm 10 mm socket (4" recommended) hex head bit 4 mm hex bit SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 6
IMPORTANT SAFETY INSTRUCTIONS CAUTION! • Proper placement of the gazebo is essential. Do not place the product underneath electrical lines. • Keep children under close supervision while they are playing around this product. This product contains small parts which can be swallowed by children. •...
Page 7
PROTECTIVE CAGE Not part of assembly. Please discard after unpacking. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
PARTS LIST ITEM DESCRIPTION THUMBNAIL QUANTITY Post leg Left beam Right beam Corner rafter Rafter branch assembly Corbel Crossbeam support bracket Roof corner cap Left middle roof panel Right middle roof panel Left small roof panel Right small roof panel Centre roof panel SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 9
PARTS LIST ITEM DESCRIPTION THUMBNAIL QUANTITY Short side centre roof edge cap Edge roof cap Main roof rafter hu b Top cover Foot plate cover Foot plate Beam corner cover Beam centre cover Netting & wall curtain hook (installed) Netting Hook (weight capacity 25 lb/11.3 kg) Magnet Tieback bracket...
Page 10
EXPLODED PARTS VIEW SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
HARDWARE LIST ITEM DESCRIPTION THUMBNAIL QUANTITY M6x10 bolt M6x15 bolt M6x40 bolt M6x55 bolt 10 mm nut with M6 threads Washer Nut cover Stake Hex key Wrench HARDWARE PACK SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 12
BEFORE YOU BEGIN ASSEMBLY MAKE SURE ALL PARTS ARE PRESENT ASSEMBLE IN A CLEARED AREA on a clean, REMOVE PACKAGING MATERIALS READ EACH STEP CAREFULLY For any questions, SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
STEP-BY-STEP GUIDE GENERAL PREPARATIONS • When choosing the location for your gazebo build, plan to have at least 6' (approximately 1.8 m) of clearance beyond the footprint of the gazebo to allow for installing parts. This is in conjunction with the Important Safety Instructions. (1.8 m) (1.8 m) •...
STEP-BY-STEP GUIDE STEP-BY-STEP GUIDE STEP 1 NOTE: Install all bolts by hand loosely threaded BEFORE fully tightening any bolts. Once all bolts are installed loosely, then secure the bolts before moving on to the next step. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 15
STEP 2 NOTE: The beam ends have preinstalled plastic inserts for easier assembly. This part is important for the complete assembly of your gazebo. Do not install bolts in the two outer holes marked with X's. NOTE: Install all bolts by hand loosely threaded BEFORE fully tightening any bolts.
Page 16
STEP-BY-STEP GUIDE STEP-BY-STEP GUIDE STEP 3 NOTE: The beam ends have preinstalled plastic inserts for easier assembly. This part is important for the complete assembly of your gazebo. TIP: NOTE: Sometimes holes aren't completely aligned. You can use the hex keys provided to help you Install all bolts by hand loosely threaded BEFORE fully align bolt holes while threading in the bolts by tightening any bolts.
Page 17
STEP 4 4&5 Ground Ground TIP: NOTE: Re-use the cardboard packaging Install all bolts by hand loosely threaded BEFORE fully to prevent damage to parts tightening any bolts. Once all bolts are installed loosely, during this step. then secure the bolts before moving on to the next step. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 18
STEP-BY-STEP GUIDE STEP-BY-STEP GUIDE STEP 5 4&5 NOTE: Install all bolts by hand loosely threaded BEFORE fully tightening any bolts. Once all bolts are installed loosely, then secure the bolts before moving on to the next step. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 19
STEP 6 4&5 NOTE: Install all bolts by hand loosely threaded BEFORE fully tightening any bolts. Once all bolts are installed loosely, then secure the bolts before moving on to the next step. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 20
STEP-BY-STEP GUIDE STEP-BY-STEP GUIDE STEP 7 NOTE: Install all bolts by hand loosely threaded BEFORE fully tightening any bolts. Once all bolts are installed loosely, then secure the bolts before moving on to the next step. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 21
STEP 8 IMPORTANT: Squaring the gazebo frame is a very important step to ensure easier assembly and proper fitment of parts. To do this, measure the distance between the legs from the outside corners of each leg post in the following order: A to B C to D These measurements should be the same.
Page 22
STEP-BY-STEP GUIDE STEP-BY-STEP GUIDE 4&5 NOTE: NOTE: Part 9 has a pin on one end. This pin should Install all bolts by hand loosely threaded BEFORE fully face upward towards the beam during tightening any bolts. Once all bolts are installed loosely, installation and install in the hole provided.
Page 23
STEP 10 NOTE: Install all bolts by hand loosely threaded BEFORE fully tightening any bolts. Once all bolts are installed loosely, then secure the bolts before moving on to the next step. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 24
STEP-BY-STEP GUIDE STEP-BY-STEP GUIDE STEP 11 TIP: If you plan to move the gazebo after fully assembling it, you can skip this step and the next step (Steps 11 & 12) and perform them after the gazebo is located in its final position. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 25
STEP 12 NOTE: Install all bolts by hand loosely threaded BEFORE fully tightening any bolts. Once all bolts are installed loosely, then secure the bolts before moving on to the next step. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 26
STEP-BY-STEP GUIDE STEP-BY-STEP GUIDE STEP 13 NOTE: Install all bolts by hand loosely threaded BEFORE fully tightening any bolts. Once all bolts are installed loosely, then secure the bolts before moving on to the next step. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 27
STEP 14 CAUTION! Be careful when unfolding the rafter branches to avoid injury or pinching. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 28
STEP-BY-STEP GUIDE STEP-BY-STEP GUIDE STEP 15 NOTE: Install all bolts by hand loosely threaded BEFORE fully tightening any bolts. Once all bolts are installed loosely, then secure the bolts before moving on to the next step. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 29
STEP 16 NOTE: NOTE: Make sure holes at bottom of panels align Install all nuts by hand loosely threaded BEFORE fully before tightening nuts fully. For a video of tightening any nuts. Once all bolts are installed loosely, this method, scan the QR code provided. then secure the nuts before moving on to the next step.
Page 30
STEP-BY-STEP GUIDE STEP-BY-STEP GUIDE STEP 17 Inside NOTE: Install all bolts by hand loosely threaded BEFORE fully tightening any bolts. Once all bolts are installed loosely, then secure the bolts before moving on to the next step. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 31
STEP 18 TIP: NOTE: Make sure holes at bottom of Install all bolts by hand loosely threaded BEFORE fully panels align before tightening tightening any bolts. Once all bolts are installed loosely, bolts fully. then secure the bolts before moving on to the next step. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 32
STEP-BY-STEP GUIDE STEP-BY-STEP GUIDE STEP 19 TIP: NOTE: Make sure holes at bottom of Install all bolts by hand loosely threaded BEFORE fully panels align before tightening tightening any bolts. Once all bolts are installed loosely, bolts fully. then secure the bolts before moving on to the next step. SKYLINE 10' x 10' SINGLE-TIER GAZEBO...
Page 33
STEP 20 20&21 NOTE: Place roof edge caps (part 20 4&5 and 21) over the ends of the roof panels as shown below. NOTE: NOTE: Do not over tighten these parts Install all bolts by hand loosely threaded BEFORE fully as they may lead to damage tightening any bolts.
Page 34
STEP-BY-STEP GUIDE STEP-BY-STEP GUIDE STEP 21 TIP: Make sure the slots on the corner caps are lined up with the roof ridges before fastening the nuts. You can slide the corner cap slightly to get the position correct before tightening. NOTE: Install all bolts by hand loosely threaded BEFORE fully tightening any bolts.
Page 35
STEP 22 TIP: There are five (5) grommets on the each side. Start hanging the netting by working your way from to right, starting at the corners. 4&5 Zipper Zipper Wall Curtain Netting Zipper Zipper Magnet Connection Here TIP: If you skipped steps 11 & 12 earlier, move your NOTE: gazebo into its finial position now.
CARING FOR YOUR ITEM Always keep children under close supervision while they are using or around this product. Never leave children unattended. This product is intended for domestic outdoor use only. Do not light any fires below or near the product. Check all nuts and bolts periodically for tightness.
WARRANTY 3 YEAR LIMITED WARRANTY* This CANVAS product carries a three (3) year warranty against defects in workmanship and materials on the frame and 1 year warranty for the remaining parts. Trileaf Distribution agrees to replace a defective product free of charge within the stated warranty period, when returned by the original purchaser with proof of purchase.
Page 39
ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 X 10 PI D’ARTICLE : 088-2258-8 INSTRUCTIONS D’ASSEMBLAGE DES DIFFICULTÉS? Balayez le code NUMÉRO SANS FRAIS : QR pour visionner 1 888 670-6684 la vidéo sur les instructions d’assemblage en IMPORTANT : Veuillez lire attentivement le ligne.
Page 40
Nous serions ravis de recevoir vos commentaires judicieux. Visitez notre site Web à canadiantire.ca pour nous communiquer de votre expérience et partagez vos photos avec nous en utilisant #MonStyleCANVAS. Montrez-nous comment vous donnez vie aux produits CANVAS . Nous avons hâte TM/MC de les voir!
Page 41
IMPORTANT COMMENT UTILISER NOS CODES QR Suivez les étapes ci-dessous pour balayer nos codes QR et accéder à des vidéos d’assemblage utiles. Ouvrez la Attendez que caméra de la caméra votre appareil reconnaisse intelligent et et balaie le pointez-le sur code QR.
Page 42
TABLE DES MATIÈRES Avertissement Outils recommandés Consignes de sécurité importantes Liste des pièces Liste du matériel Préparations générales Directives détaillées Entretien de votre article Garantie AVERTISSEMENT! POUR RÉDUIRE LE RISQUE DE BLESSURES GRAVES, LISEZ LES CONSIGNES DE SÉCURITÉ CI-APRÈS. Attention! Ayez toujours les enfants sous étroite surveillance pendant qu’ils jouent à...
Page 43
Escabeau de 8 pi ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 44
ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 X 10 PI...
Page 45
CAGE DE PROTECTION Ne fait pas partie de l'assemblage. Veuillez jeter après le déballage. ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 46
RÉFÉRENCE Patte de poteau Poutre de gauche Poutre de droite Chevron de coin Assemblage de branche à chevron Corbeau Support de traverse Capuchon de coin du toit Panneau de toit latéral gauche du milieu Panneau de toit latéral droit du milieu Petit panneau de toit latéral gauche Petit panneau de...
Page 47
RÉFÉRENCE Chapeau de rebord de toit latéral central Chapeau de rebord de toit latéral Moyeu de chevron de toit principal Couvercle supérieur Protège-plaque de pied Plaque de pied Protège-poutre de coin Protège-poutre central Crochet pour mousquetaire et rideau (installé) Mousquetaire Crochet (poids maximal : 25 lb/11,3 kg) Aimant...
Page 48
VUE ÉCLATÉE ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
LISTE DU MATÉRIEL RÉFÉRENCE DESCRIPTION ILLUSTRATION QUANTITÉ Boulon M6x10 Boulon M6x15 Boulon M6x40 Boulon M6x55 Écrou de 10 mm avec filetages M6 Rondelle Cache-écrou Piquet Clé hexagonale Clé QUINCAILLERIE MATÉRIEL ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 50
LISEZ CHAQUE ÉTAPE AVEC SOIN Assurez-vous de comprendre chaque étape. Pour toute question, veuillez communiquer avec le service à la clientèle de CANVAS au 1 888 660-6684 (sans frais). ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
STEP-BY-STEP GUIDE PRÉPARATIONS GÉNÉRALES • Au moment de choisir l’emplacement de l’abri de jardin, prévoyez un dégagement d’au moins 6 pi (environ 1,8 m) au-delà de l’espace de labri de jardin pour permettre l’installation des pièces. Ceci est jumelé avec les consignes de sécurité importantes. 6 pi 6 pi (1,8 m)
Page 52
STEP-BY-STEP GUIDE DIRECTIVES DÉTAILLÉ ÉTAPE 1 REMARQUE : Installez tous les boulons à la main sans les serrer, AVANT de les serrer complètement. Une fois que tous les boulons sont installés, serrez-les avant de passer à l’étape suivante. ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 53
ÉTAPE 2 REMARQUE : Les extrémités de la poutre sont dotées d’un accessoire préinstallé en plastique pour faciliter l’assemblage de votre abri de jardin. REMARQUE : N’installez pas de boulons dans les deux trous extérieurs indiqués par un X. REMARQUE : Installez tous les boulons à...
DIRECTIVES DÉTAILLÉES ÉTAPE 3 REMARQUE : Les extrémités de la poutre sont dotées d’un accessoire préinstallé en plastique pour faciliter l’assemblage de votre abri de jardin. ASTUCE : REMARQUE : Parfois, les trous ne sont pas complètement Installez tous les boulons à la main sans les serrer, alignés.
Page 55
ÉTAPE 4 4 et 5 Ground ASTUCE : REMARQUE : Réutilisez l’emballage en carton pour éviter d’endommager les Installez tous les boulons à la main sans les serrer, pièces à cette étape. AVANT de les serrer complètement. Une fois que tous les boulons sont installés, serrez-les avant de passer à...
Page 56
DIRECTIVES DÉTAILLÉES ÉTAPE 5 4 et 5 REMARQUE : Installez tous les boulons à la main sans les serrer, AVANT de les serrer complètement. Une fois que tous les boulons sont installés, serrez-les avant de passer à l’étape suivante. ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 57
ÉTAPE 6 4 et 5 REMARQUE : Installez tous les boulons à la main sans les serrer, AVANT de les serrer complètement. Une fois que tous les boulons sont installés, serrez-les avant de passer à l’étape suivante. ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 58
DIRECTIVES DÉTAILLÉES ÉTAPE 7 REMARQUE : Installez tous les boulons à la main sans les serrer, AVANT de les serrer complètement. Une fois que tous les boulons sont installés, serrez-les avant de passer à l’étape suivante. ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 59
ÉTAPE 8 IMPORTANT: L’équerrage du cadre de l’abri de jardin est une étape très importante pour faciliter l’assemblage et assurer un bon ajustement des pièces. Pour ce faire, mesurez la distance entre les pieds et les coins extérieurs de chaque pied dans l’ordre suivant : A à...
Page 60
DIRECTIVES DÉTAILLÉES ÉTAPE 9 4&5 REMARQUE : REMARQUE : La pièce 9 comporte une goupille à une Installez tous les boulons à la main sans les serrer, AVANT extrémité. Cette goupille doit être orientée de les serrer complètement. Une fois que tous les boulons vers le haut vers la poutre pendant sont installés, serrez-les avant de passer à...
Page 61
ÉTAPE 10 REMARQUE : Installez tous les boulons à la main sans les serrer, AVANT de les serrer complètement. Une fois que tous les boulons sont installés, serrez-les avant de passer à l’étape suivante. ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 62
DIRECTIVES DÉTAILLÉES ÉTAPE 11 ASTUCE : Si vous prévoyez déplacer l’abri de jardin après l’avoir assemblé complètement, vous pouvez sauter cette étape et l’étape suivante (étapes 11 et 12) et les effectuer après que l’abri de jardin soit à son emplacement final. ABRI DE JARDIN SKYLINE À...
Page 63
ÉTAPE 12 REMARQUE : Installez tous les boulons à la main sans les serrer, AVANT de les serrer complètement. Une fois que tous les boulons sont installés, serrez-les avant de passer à l’étape suivante. ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 64
DIRECTIVES DÉTAILLÉES ÉTAPE 13 REMARQUE : Installez tous les boulons à la main sans les serrer, AVANT de les serrer complètement. Une fois que tous les boulons sont installés, serrez-les avant de passer à l’étape suivante. ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 65
ÉTAPE 14 ATTENTION! Soyez prudent lorsque vous dépliez les branches à chevron pour éviter les blessures ou les pincements. ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 66
DIRECTIVES DÉTAILLÉES ÉTAPE 15 REMARQUE : Installez tous les boulons à la main sans les serrer, AVANT de les serrer complètement. Une fois que tous les boulons sont installés, serrez-les avant de passer à l’étape suivante. ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 67
ÉTAPE 16 REMARQUE : REMARQUE : Assurez-vous que les trous au bas des Installez tous les écrous à la main sans les serrer, panneaux s’alignent avant de serrer AVANT de les serrer complètement. Une fois que tous complètement les écrous. Pour une vidéo les boulons sont installés, puis serrez les écrous avant de cette méthode, balayez le code QR de passer à...
Page 68
DIRECTIVES DÉTAILLÉES ÉTAPE 17 Inside REMARQUE : Installez tous les boulons à la main sans les serrer, AVANT de les serrer complètement. Une fois que tous les boulons sont installés, serrez-les avant de passer à l’étape suivante. ABRI DE JARDIN SKYLINE À TOIT À UN NIVEAU, 10 x 10 PI...
Page 69
ÉTAPE 18 ASTUCE : REMARQUE : Assurez-vous que les trous au Installez tous les boulons à la main sans les serrer, AVANT bas des panneaux s’alignent de les serrer complètement. Une fois que tous les boulons avant de serrer complètement sont installés, serrez-les avant de passer à...
Page 70
DIRECTIVES DÉTAILLÉES ÉTAPE 19 ASTUCE : REMARQUE : Assurez-vous que les trous au Installez tous les boulons à la main sans les serrer, AVANT bas des panneaux s’alignent de les serrer complètement. Une fois que tous les boulons avant de serrer complètement sont installés, serrez-les avant de passer à...
Page 71
ÉTAPE 20 20 et 21 REMARQUE : Placez les capuchons de bord de toit (parties 20 et 21) sur les 4 et 5 extrémités des panneaux de toit, comme indiqué ci-dessous. REMARQUE : REMARQUE : Aucun boulon ne doit être installé...
Page 72
DIRECTIVES DÉTAILLÉES ÉTAPE 21 ASTUCE : Assurez-vous que les fentes des capuchons de coin sont alignées avec les arêtes du toit avant de serrer les écrous. Vous pouvez faire glisser légèrement le capuchon de coin pour corriger la position avant de serrer les écrous. REMARQUE : Installez tous les boulons à...
Page 73
ÉTAPE 22 ASTUCE : Il y a cinq (5) œillets sur les côtés. Commencez à suspendre le moustiquaire en allant de gauche à droite, en commençant par les coins. 4&5 Fermeture à glissière Fermeture à glissière Rideau mural Mousquetaire Fermeture à glissière Fermeture à...
ENTRETIEN DE VOTRE ARTICLE Surveillez toujours les enfants étroitement lorsqu’ils utilisent cet article ou qu’ils se trouvent à proximité de celui-ci. Ne laissez jamais les enfants sans surveillance. Cet article est uniquement destiné à un usage domestique et doit être utilisé à l’extérieur.
GARANTIE GARANTIE LIMITÉE DE 3 ANS* TM/MC Cet article CANVAS comprend une garantie de trois (3) ans contre les défauts de fabrication et de matériaux du cadre et un (1) an de garantie pour toutes les autres pièces. Distribution Trifeuil consent à remplacer l’article défectueux sans frais lorsqu’il est retourné, accompagné...
Need help?
Do you have a question about the SKYLINE 088-2258-8 and is the answer not in the manual?
Questions and answers
M6 x15mm bolt and washer replacements; can you send drawing of size configuration.Also, where can I find replacements, no luck finding.
Replacements for the M6 x 15 mm bolts and washers for Canvas part number SKYLINE 088-2258-8 can be obtained by calling 1-888-670-6684.
This answer is automatically generated