Maintenance - DeWalt DCF894 Original Instructions Manual

installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
Usage
Your impact tool generates the following maximum torque.
NOTE: Output torque is dependent on the speed selected, with
the highest provided in the Precision Wrench™ mode.
Cat # Ft.-Lbs.
Low/High/
Precision Wrench™
DCF894, DCF894H 0–150/0–330/0–330
CAUTION: Ensure fastener and/or system will withstand
the level of torque generated by the tool. Excessive torque
may cause breakage and possible personal injury.
1. Place the accessory on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press switch to start operation. Release the switch to stop
operation. Always check torque with a torque wrench, as the
fastening torque is affected by many factors including the
following:
- Voltage: Low voltage, due to a nearly discharged battery,
will reduce fastening torque.
- Accessory size: Failure to use the correct accessory size
will cause a reduction in fastening torque.
- Bolt Size: Larger bolt diameters generally require higher
fastening torque. Fastening torque will also vary according
to length, grade, and torque coefficient.
- Bolt: Ensure that all threads are free of rust and other
debris to allow proper fastening torque.
- Material: The type of material and surface finish of the
material will affect fastening torque.
- Fastening Time: Longer fasten ing time results in
increased fastening torque. Using a longer fastening
time than recom mended could cause the fasteners to be
overstressed, stripped or damaged.

MAINTENANCE

Your D WALT power tool has been designed to operate
E
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
.
4
Nm
Low/High/
Precision Wrench™
200/447/447
Optional Accessories
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails to
produce sufficient power on jobs which were easily done before.
At the end of its technical life, discard it with due care for our
environment:
•
•
Autogoods "130"
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
E
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
WARNING: To reduce the risk of injury, use only D
impact-ready accessories.
WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous condition.
Inspect accessories prior to use to ensure that they con tain
no cracks.
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
Run the battery pack down completely, then remove it from
the tool.
Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
ENGLISH
WALT recommended
E
WALT
E
13